Skip to content

Chapter 8 — CHIMNEYS AND VENTS

802.12 Draft Hoods and Draft Controls.

California Mechanical Code (Title 24, Part 4) · 2019 edition · updated 2026-09-10 · California

Italicized text is a California amendment to the model code, as printed in the official publication.

Vented appliances shall be installed with draft hoods. Exception: Dual oven-type combination ranges; incinerators; direct-vent appliances; fan-assisted combustion system appliances; appliances requiring chimney draft for operation; single firebox boilers equipped with conversion burners with

146 2019 CALIFORNIA MECHANICAL CODE

CHIMNEYS AND VENTS

inputs exceeding 400 000 Btu/h (117 kW); appliances equipped with blast, power, or pressure burners that are not listed for use with draft hoods; and appliances designed for forced venting.

802.12.1 Installation. A draft hood supplied with or forming a part of listed vented appliances shall be installed without alteration, exactly as furnished and specified by the appliance manufacturer. [NFPA 54:12.13.2]

Get a plain-English answer with a citation back to this text.

Ask AI about this code
Export this section
▸Contents — California Mechanical Code (Title 24, Part 4)
California Mechanical Code (Title 24, Part 4)
  1. Chapter 1 — GENERAL CODE PROVISIONS
  2. Chapter 2 — DEFINITIONS
  3. Chapter 3 — GENERAL REGULATIONS
  4. Chapter 4 — VENTILATION AIR
  5. Chapter 5 — EXHAUST SYSTEMS
  6. Chapter 6 — DUCT SYSTEMS
  7. Chapter 7 — COMBUSTION AIR
  8. ▸Chapter 8 — CHIMNEYS AND VENTS
    Overview
    1. 801.1 Applicability.801.0 General. The requirements of this ch…
    2. 801.2 Venting of Gas Appliances. Low-heat and
    3. 801.3 Appliances Fueled by Other Fuels. Appliances
    4. 802.1 Listing.802.0 Venting of Appliances. Type B and Type B-W…
    5. 802.2 Connection to Venting Systems. Except as permitted in Se…
    6. 802.3 Design and Construction. Venting systems shall
    7. 802.4 Type of Venting System to be Used. The type of
    8. 802.5 Masonry, Metal, and Factory-Built Chimneys. Chimneys sha…
    9. 802.6 Gas Vents. The installation of gas vents shall meet
    10. 802.7 Single-Wall Metal Pipe. Single-wall metal pipe
    11. 802.8 Through-the-Wall Vent Termination. A mechanical draft ve…
    12. 802.9 Condensation Drain. Provision shall be made to
    13. 802.10 Vent Connectors for Category I Appliances.
    14. 802.11 Vent Connectors for Category II, Category III,and Categ…
    15. 802.12 Draft Hoods and Draft Controls. Vented appliances shall…
    16. 802.14 Obstructions. Devices that retard the flow of vent
    17. 802.13 Manually Operated Dampers. A manually operated damper s…
    18. 802.15 Automatically Operated Vent Dampers. An
    19. 803.1 Single Appliance Vent Table 803.1.2(1) through
    20. 803.2 Multiple Appliance Vent Table 803.2(1) through
  9. Chapter 9 — INSTALLATION OF SPECIFIC APPLIANCES
  10. Chapter 10 — BOILERS AND PRESSURE VESSELS
  11. Chapter 11 — REFRIGERATION
  12. Chapter 12 — HYDRONICS
  13. Chapter 13 — FUEL GAS PIPING
  14. Chapter 14 — PROCESS PIPING
  15. Chapter 15 — SOLAR ENERGY SYSTEMS
  16. Chapter 16 — STATIONARY POWER PLANTS
  17. Chapter 17 — REFERENCED STANDARDS
  18. Appendix A — RESIDENTIAL PLAN EXAMINER REVIEW FORM FOR HVAC SY…
  19. Appendix B — PROCEDURES TO BE FOLLOWED TO PLACE GAS EQUIPMENT …
  20. Appendix C — INSTALLATION AND TESTING OF OIL (LIQUID) FUEL-FIR…
  21. Appendix D — FUEL SUPPLY: MANUFACTURED/MOBILE HOME PARKS AND R…
  22. Appendix E — SUSTAINABLE PRACTICES
  23. Appendix F — SIZING OF VENTING SYSTEMS AND OUTDOOR COMBUSTION …
  24. Appendix G — EXAMPLE CALCULATION OF OUTDOOR AIR RATE

GoCodebook provides public access, search, citation, multilingual explanation, and practical interpretation of legally adopted building regulations. It is not a substitute for the official ICC or California code publications.