510.2 Multiple Appliance Vent Table 510.2(1) through

Table 510.2(9). Venting Table 510.2(1) through Table 510.2(9) shall not be used where obstructions are installed in the venting system. The installation of vents serving listed appliances with vent dampers shall be in accordance with the appliance manufacturer’s instructions, or in accordance with the following: (1) The maximum capacity of the vent connector shall be

determined using the NAT Max column. (2) The maximum capacity of the vertical vent or chimney

shall be determined using the FAN + NAT column when the second appliance is a fan-assisted appliance, or the NAT + NAT column when the second appliance is equipped with a draft hood.

2022 CALIFORNIA PLUMBING CODE 105

WATER HEATERS

(3) The minimum capacity shall be determined as if the

appliance were a fan-assisted appliance, as follows: (a) The minimum capacity of the vent connector shall

be determined using the FAN Min column. (b) The FAN + FAN column shall be used when the

second appliance is a fan-assisted appliance, and the FAN + NAT column shall be used when the second appliance is equipped with a draft hood, to determine whether the vertical vent or chimney configuration is not permitted (NA). Where the vent configuration is NA, the vent configuration shall not be permitted and an alternative venting configuration shall be utilized. [NFPA 54:13.2.1] 510.2.1 Vent Connector Maximum Length. The maximum vent connector horizontal length shall be 18 inches per inch (18 mm/mm) of connector diameter as shown in Table 510.2.1, or as permitted by Section 510.2.2. [NFPA 54:13.2.2]

TABLE 510.2.1 VENT CONNECTOR MAXIMUM LENGTH

[NFPA 54: TABLE 13.2.2]

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm

510.2.2 Vent Connector Exceeding Maximum Length. The vent connector shall be routed to the vent utilizing the shortest possible route. Connectors with longer horizontal lengths than those listed in Table 510.2.1 are permitted under the following conditions: (1) The maximum capacity (FAN Max or NAT Max) of

the vent connector shall be reduced 10 percent for each additional multiple of the length listed in Table 510.2.1. For example, the maximum length listed for a 4 inch (100 mm) connector is 6 feet (1829 mm). With a connector length greater than 6 feet (1829 mm) but not exceeding 12 feet (3658 mm), the maximum capacity must be reduced by 10 percent (0.90 x maximum vent connector capacity). With a connector length greater than 12 feet (3658 mm) but not

exceeding 18 feet (5486 mm), the maximum capacity shall be reduced by 20 percent (0.80 x maximum vent capacity). (2) For a connector serving a fan-assisted appliance, the

minimum capacity (FAN Min) of the connector shall be determined by referring to the corresponding single appliance table. For Type B double-wall connectors, Table 510.1.2(1) shall be used. For single-wall connectors, Table 510.1.2(2) shall be used. The height ( H ) and lateral ( L ) shall be measured according to the procedures for a single appliance vent, as if the other appliances were not present. [NFPA 54:13.2.3] 510.2.3 Vent Connector Manifolds. Where the vent connectors are combined prior to entering the vertical portion of the common vent to form a common vent manifold, the size of the common vent manifold and the common vent shall be determined by applying a 10 percent reduction (0.90 x maximum common vent capacity) to the common vent capacity part of the common vent tables. The length of the common vent manifold ( LM ) shall not exceed 18 inches per inch (18 mm/mm) of common vent diameter ( D ). [NFPA 54:13.2.4] 510.2.4 Vent Offsets. Where the common vertical vent is offset, the maximum capacity of the common vent shall be reduced in accordance with Section 510.2.5, and the horizontal length of the common vent offset shall not exceed 18 inches per inch (18 mm/mm) of common vent diameter ( D ). Where multiple offsets occur in a common vent, the total horizontal length of all offsets combined shall not exceed 18 inches per inch (18 mm/mm) of the common vent diameter. [NFPA 54:13.2.5] 510.2.5 Elbows in Vents. For each elbow up to and including 45 degrees (0.79 rad) in the common vent, the maximum common vent capacity listed in the venting tables shall be reduced by 5 percent. For each elbow greater than 45 degrees (0.79 rad) up to and including 90 degrees (1.57 rad), the maximum common vent capacity listed in the venting tables shall be reduced by 10 percent. [NFPA 54:13.2.6] 510.2.6 Elbows in Connectors. The vent connector capacities listed in the common vent sizing tables include allowance for two 90 degree (1.57 rad) elbows. For each additional elbow up to and including 45 degrees (0.79 rad), the maximum vent connector capacity listed in the venting tables shall be reduced by 5 percent. For each elbow greater than 45 degrees (0.79 rad) up to and including 90 degrees (1.57 rad), the maximum vent connector capacity listed in the venting tables shall be reduced by 10 percent. [NFPA 54:13.2.7] 510.2.7 Common Vent Minimum Size. The crosssectional area of the common vent shall be equal to or greater than the cross-sectional area of the largest connector. [NFPA 54:13.2.8] 510.2.8 Tee and Wye Fittings. Tee and wye fittings connected to a common gas vent shall be considered as part of the common gas vent and constructed of materials consistent with that of the common gas vent. [NFPA 54:13.2.9]

106 2022 CALIFORNIA PLUMBING CODE

510.2.9 Size of Fittings. At the point where tee or wye fittings connect to a common gas vent, the opening size of the fitting shall be equal to the size of the common vent. Such fittings shall not be prohibited from having reduced size openings at the point of connection of appliance gas vent connectors. [NFPA 54:13.2.10] 510.2.10 High-Altitude Installations. Sea level input ratings shall be used when determining maximum capacity for high-altitude installation. Actual input (derated for altitude) shall be used for determining minimum capacity for high-altitude installation. [NFPA 54:13.2.11] 510.2.11 Connector Rise. The connector rise ( R ) for each appliance connector shall be measured from the draft hood outlet or flue collar to the centerline where the vent gas streams come together. [NFPA 54:13.2.12] 510.2.12 Vent Height. For multiple appliances all located on one floor, available total height ( H ) shall be measured from the highest draft hood outlet or flue collar up to the level of the outlet of the common vent.

[NFPA 54:13.2.13] 510.2.13 Multistory Installations. For multistory installations, available total height ( H ) for each segment of the system shall be the vertical distance between the highest draft hood outlet or flue collar entering that segment and the centerline of the next higher interconnection tee. [NFPA 54:13.2.14]

510.2.14 Size of Vents for Multistory Installa- tions. The size of the lowest connector and of the vertical vent leading to the lowest interconnection of a multistory system shall be in accordance with Table 510.1.2(1) or Table 510.1.2(2) for available total height ( H ) up to the lowest interconnection. [NFPA 54:13.2.15] 510.2.15 Vent Type Multistory Installations. Where used in multistory systems, vertical common vents shall be Type B double wall and shall be installed with a listed vent cap. [NFPA 54:13.2.16] 510.2.16 Offsets in Multistory Installations. Offsets in multistory common vent systems shall be limited to a single offset in each system, and systems with an offset shall comply with all of the following: (1) The offset angle shall not exceed 45 degrees (0.79

rad) from vertical. (2) The horizontal length of the offset shall not exceed

18 inches per inch (18 mm/mm) of common vent diameter of the segment in which the offset is located. (3) For the segment of the common vertical vent con taining the offset, the common vent capacity listed in the common venting tables shall be reduced by 20 percent (0.80 x maximum common vent capacity). (4) A multistory common vent shall not be reduced in

size above the offset. [NFPA 54:13.2.17] 510.2.17 Vertical Vent Size Limitation. Where two or more appliances are connected to a vertical vent or chimney, the flow area of the largest section of vertical vent or chimney shall not exceed seven times the small

WATER HEATERS

est listed appliance categorized vent areas, flue collar area, or draft hood outlet area unless designed in accordance with approved engineering methods. [NFPA 54:13.2.18] 510.2.18 Multiple Input Ratings. For appliances with more than one input rate, the minimum vent connector capacity (FAN Min) determined from the tables shall be less than the lowest appliance input rating, and the maximum vent connector capacity (FAN Max or NAT Max) determined from the tables shall be greater than the highest appliance input rating. [NFPA 54:13.2.19]

510.2.19 Corrugated Metallic Chimney Liner Reduction. Listed corrugated metallic chimney liner systems in masonry chimneys shall be sized by using Table 510.2(1) or Table 510.2(2) for Type B vents, with the maximum capacity reduced by 20 percent (0.80 x maximum capacity) and the minimum capacity as shown in Table 510.2(1) or Table 510.2(2). Corrugated metallic liner systems installed with bends or offsets shall have their maximum capacity further reduced in accordance with Section 510.2.4 and Section 510.2.5. The 20 percent reduction for corrugated metallic chimney liner systems includes an allowance for one long radius 90 degree (1.57 rad) turn at the bottom of the liner. [NFPA 54:13.2.20] 510.2.20 Chimneys and Vents. Table 510.2(1) through Table 510.2(5) shall be used only for chimneys and vents not exposed to the outdoors below the roof line. A Type B vent or listed chimney lining system passing through an unused masonry chimney flue shall not be considered to be exposed to the outdoors. A Type B vent passing through an unventilated enclosure or chase insulated to a value of not less than R8 shall not be considered to be exposed to the outdoors. Where vents extend outdoors above the roof more than 5 feet (1524 mm) higher than required by Table 509.6.1, and where vents terminate in accordance with Section 509.6.1(1)(b), the outdoor portion of the vent shall be enclosed as required by this section for vents not considered to be exposed to the outdoors, or such venting system shall be engineered. Table 510.2(6) through Table 510.2(9) shall be used for clay tile lined exterior masonry chimneys, provided all the following conditions are met: (1) The vent connector is Type B double wall. (2) At least one appliance is draft hood equipped. (3) The combined appliance input rating is less than the

maximum capacity given by Table 510.2(6) (for NAT + NAT) or Table 510.2(8) (for FAN + NAT). (4) The input rating of each space-heating appliance is

greater than the minimum input rating given by Table 510.2(7) (for NAT + NAT) or Table 510.2(9) (for FAN + NAT). (5) The vent connector sizing is in accordance with

Table 510.2(3). [NFPA 54:13.2.22] 510.2.21 Vent Connector Sizing. Vent connectors shall not be increased more than two sizes greater than the listed appliance categorized vent diameter, flue col

2022 CALIFORNIA PLUMBING CODE 107

WATER HEATERS

lar diameter, or draft hood outlet diameter. Vent connectors for draft hood-equipped appliances shall not be smaller than the draft hood outlet diameter. Where a vent connector size(s) determined from the tables for a fanassisted appliance(s) is smaller than the flue collar diameter, the use of the smaller size(s) shall be permitted, provided that the installation complies with all of the following conditions: (1) Vent connectors for fan-assisted appliance flue col lars 12 inches (300 mm) in diameter or smaller are not reduced by more than one table size [e.g., 12 inches to 10 inches (300 mm to 250 mm) is a onesize reduction], and those larger than 12 inches (300 mm) in diameter are not reduced more than two table sizes [e.g., 24 inches to 20 inches (600 mm to 500 mm) is a two-size reduction]. (2) The fan-assisted appliance(s) is common vented

with a draft hood-equipped appliance(s). (3) The vent connector has a smooth interior wall.

[NFPA 54:13.2.24] 510.2.22 Combination of Pipe Types and Sizes. All combinations of pipe sizes, single-wall metal pipe, and double-wall metal pipe shall be allowed within any connector run(s) or within the common vent, provided ALL of the appropriate tables permit ALL of the desired sizes and types of pipe, as if they were used for the entire length of the subject connector or vent. Where singlewall and Type B double-wall metal pipes are used for vent connectors within the same venting system, the common vent shall be sized using Table 510.2(2) or Table 510.2(4) as appropriate. [NFPA 54:13.2.25] 510.2.23 Multiple Connector and Vent Sizes. Where Table 510.2(1) through Table 510.2(9) permits more than one diameter of pipe to be used for a connector or vent, all the permitted sizes shall be permitted to be used. [NFPA 54:13.2.26] 510.2.24 Interpolation. Interpolation shall be permitted in calculating capacities for vent dimensions that fall between table entries. [NFPA 54:13.2.27] 510.2.25 Extrapolation. Extrapolation beyond the table entries shall not be permitted. [NFPA 54:13.2.28] 510.2.26 Engineering Methods. For vent heights lower than 6 feet (1829 mm) and higher than shown in the tables, engineering methods shall be used to calculate vent capacities. [NFPA 54:13.2.29] 510.2.27 Height Entries. Where the actual height of a vent falls between entries in the height column of the applicable table in Table 510.2(1) through Table 510.2(9), either of the following shall be used: (1) Interpolation.

(2) The lower appliance input rating shown in the table

entries, for FAN Max and NAT Max column values; and the higher appliance input rating for the FAN Min column values. [NFPA 54:13.2.30]

108 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

99% Winter Design Temperatures for the Contiguous United States This map is a necessarily generalized guide to temperatures in the contiguous United States. Temperatures shown for areas such as mountainous regions and large urban centers are not necessarily accurate. The climate data used to develop this map are from the ASHRAE Handbook — Fundamentals (Climate Conditions for the United States).

99% Winter Design Temperatures for the Contiguous United States* This map is a necessarily generalized guide to temperatures in the contiguous United States. Temperatures shown for areas such as mountainous regions and large urban centers are not necessarily accurate. The climate data used to develop this map are from the ASHRAE Handbook — Fundamentals (Climate Conditions for the United States).

For 99% winter design temperatures in Alaska, consult the ASHRAE Handbook — Fundamentals. 99% winter design temperatures for Hawaii are greater than 37°F For SI units: °C = (°F-32)/1.8

FIGURE 510.1.10 RANGE OF WINTER DESIGN TEMPERATURES USED IN ANALYZING EXTERIOR MASONRY CHIMNEYS IN THE UNITED STATES

[NFPA 54: FIGURE F.2.4]

2022 CALIFORNIA PLUMBING CODE 109

WATER HEATERS

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

110 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

2022 CALIFORNIA PLUMBING CODE 111

WATER HEATERS

TABLE 510.1.2(1) TYPE B DOUBLE-WALL GAS VENT [NFPA 54: TABLE 13.1(a)] (continued)

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

112 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 113

WATER HEATERS

TABLE 510.1.2(2) TYPE B DOUBLE-WALL GAS VENT [NFPA 54: TABLE 13.1(b)] (continued)*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

114 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.1.2(3) MASONRY CHIMNEY [NFPA 54: TABLE 13.1(c)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 115

WATER HEATERS

TABLE 510.1.2(3) MASONRY CHIMNEY [NFPA 54: TABLE 13.1(c)] (continued)*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

116 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.1.2(4) MASONRY CHIMNEY [NFPA 54: TABLE 13.1(d)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 117

WATER HEATERS

TABLE 510.1.2(4) MASONRY CHIMNEY [NFPA 54: TABLE 13.1(d)] (continued)*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

118 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.1.2(5) SINGLE-WALL METAL PIPE OR TYPE B ASBESTOS-CEMENT VENT [NFPA 54: TABLE 13.1(e)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 119

WATER HEATERS

TABLE 510.1.2(6) EXTERIOR MASONRY CHIMNEY [NFPA 54: TABLE 13.1(f)] ^{1, 2}

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ², °C = (°F-32)/1.8 Notes: 1 See Figure 510.1.10 for a map showing local 99 percent winter design temperatures in the United States. 2 NA: Not applicable.

120 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.2(1) TYPE B DOUBLE-WALL VENT [NFPA 54: TABLE 13.2(a)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 121

WATER HEATERS

TABLE 510.2(1) TYPE B DOUBLE-WALL VENT [NFPA 54: TABLE 13.2(a)] (continued)

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

122 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.2(1) TYPE B DOUBLE-WALL VENT [NFPA 54: TABLE 13.2(a)] (continued)*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 123

WATER HEATERS

TABLE 510.2(1) TYPE B DOUBLE-WALL VENT [NFPA 54: TABLE 13.2(a)] (continued)*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

124 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.2(2) TYPE B DOUBLE-WALL VENT [NFPA 54: TABLE 13.2(b)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 125

WATER HEATERS

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

126 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.2(3) MASONRY CHIMNEY [NFPA 54: TABLE 13.2(c)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 127

WATER HEATERS

TABLE 510.2(3) MASONRY CHIMNEY [NFPA 54: TABLE 13.2(c)] (continued)*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

128 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.2(4) MASONRY CHIMNEY [NFPA 54: TABLE 13.2(d)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 129

WATER HEATERS

TABLE 510.2(4) MASONRY CHIMNEY [NFPA 54: TABLE 13.2(d)] (continued)*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

130 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.2(5) SINGLE-WALL METAL PIPE OR TYPE B ASBESTOS-CEMENT VENT [NFPA 54: TABLE 13.2(e)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

TABLE 510.2(6) EXTERIOR MASONRY CHIMNEY [NFPA 54: TABLE 13.2(f)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 131

WATER HEATERS

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ², °C = (°F-32)/1.8 Notes: 1 See Figure 510.1.10 for a map showing local 99 percent winter design temperatures in the United States. 2 NA: Not applicable.

132 2022 CALIFORNIA PLUMBING CODE

WATER HEATERS

TABLE 510.2(8) EXTERIOR MASONRY CHIMNEY [NFPA 54: TABLE 13.2(h)]*

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ²

• NA: Not applicable.

2022 CALIFORNIA PLUMBING CODE 133

WATER HEATERS

For SI units: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1000 British thermal units per hour = 0.293 kW, 1 square inch = 0.000645 m ², °C = (°F-32)/1.8 Notes: 1 See Figure 510.1.10 for a map showing local 99 percent winter design temperatures in the United States. 2 NA: Not applicable.

134 2022 CALIFORNIA PLUMBING CODE

CALIFORNIA PLUMBING CODE – MATRIX ADOPTION TABLE