Chapter 44 — REFERENCED STANDARDS

(Matrix Adoption Tables are nonregulatory, intended only as an aid to the code user.

See Chapter 1 for state agency authority and building applications.)

Adopting agency	BSC	BSC- CG	SFM	HCD			DSA			OSHPD						BSCC	DPH	AGR	DWR	CEC	CA	SL	SLC
Adopting agency	BSC	BSC- CG	SFM	1	2	1/AC	AC	SS	SS/ CC	1	1R	2	3	4	5	5	5	5	5	5	5	5	5
Adopt entire chapter
Adopt entire chapter as amended (amended sections listed below)			X	X
Adopt only those sections that are listed below			X
Chapter / Section
ANSI			X
ASTM			X	X
ICC			X
IFC-18				X
NFPA			X
SFM			X
UBC			X

Copyright © 2019 ICC. ALL RIGHTS RESERVED. Accessed by Kevin Day (kevin.day@dgs.ca.gov), (California Building Standards Commission) Order Number #100735044 on Jul 24, 2019 03:54 PM (PDT) pursuant to License Agreement with ICC. No further reproduction or distribution authorized. Single user only, copying and networking prohibited. ANY UNAUTHORIZED REPRODUCTION OR DISTRIBUTION IS A VIOLATION OF THE FEDERAL COPYRIGHT ACT AND THE LICENSE AGREEMENT, AND SUBJECT TO CIVIL AND CRIMINAL PENALTIES THEREUNDER.

100735044

534 2019 CALIFORNIA RESIDENTIAL CODE Copyright © 2019 ICC. ALL RIGHTS RESERVED. Accessed by Kevin Day (kevin.day@dgs.ca.gov), (California Building Standards Commission) Order Number #100735044 on Jul 24, 2019 03:54 PM (PDT) pursuant to License Agreement with ICC. No further reproduction or distribution authorized. Single user only, copying and networking prohibited. ANY UNAUTHORIZED REPRODUCTION OR DISTRIBUTION IS A VIOLATION OF THE FEDERAL COPYRIGHT ACT AND THE LICENSE AGREEMENT, AND SUBJECT TO CIVIL AND CRIMINAL PENALTIES THEREUNDER.

100735044

Part IX—Referenced Standards

CHAPTER 44

REFERENCED STANDARDS

Notwithstanding California laws and regulations, these referenced standards shall be applicable only to those California Residential Code sections that are adopted.

User note:

About this chapter: The one- and two-family dwelling code contains numerous references to standards promulgated by other organizations that are used to provide requirements for materials, products and methods of construction. Chapter 44 contains a comprehensive list of all standards that are referenced in this code. These standards, in essence, are part of this code to the extent of the reference to the standard.

he one- and two-family dwelling code contains numerous references to standards promulgated by other organizations_ that are used to provide requirements for materials, products and methods of construction. Chapter 44 contains a comprehensive list of all standards that are referenced in this code. These standards, in essence, are part of this code to the extent of the reference to the standard.

This chapter lists the standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title, and the section or sections of this document that reference the standard. The application of the referenced standards shall be as specified in Section R102.4.

AAMA American Architectural Manufacturers Association

1827 Walden Office Square, Suite 550 Schaumburg, IL 60173

AAMA/WDMA/CSA 101/I.S.2/A440—17: North American Fenestration Standards/Specifications for Windows, Doors and Skylights

R308.6.9, R609.3

450—10: Voluntary Performance Rating Method for Mulled Fenestration Assemblies R609.8

506—16: Voluntary Specifications for Hurricane Impact and Cycle Testing of Fenestration Products R609.6.1

711—16: Voluntary Specification for Self-adhering Flashing Used for Installation of Exterior Wall Fenestration Products R703.4

712—14: Voluntary Specification for Mechanically Attached Flexible Flashing R703.4

714—15: Voluntary Specification for Liquid Applied Flashing Used to Create a Water-resistive Seal around Exterior Wall Openings in Buildings

R703.4

AAMA/NPEA/NSA 2100—12: Specifications for Sunrooms

R301.2.1.1.1

ACCA Air Conditioning Contractors of America

2800 Shirlington Road, Suite 300 Arlington, VA 22206

Manual D—2016: Residential Duct Systems

Table R301.2(1)

ACI American Concrete Institute

38800 Country Club Drive Farmington Hills, MI 48331

318—14: Building Code Requirements for Structural Concrete R301.2.2.2.5, R402.2, Table R404.1.2(2), Table R404.1.2(5), Table R404.1.2(6), Table R404.1.2(7), Table R404.1.2(8), R404.1.3, R404.1.3.1, R404.1.3.3, R404.1.3.4, R404.1.4.2, R404.5.1, R608.1, R608.1.1, R608.1.2, R608.2, R608.5.1, R608.6.1, R608.8.2, R608.9.2, R608.9.3

332—14: Residential Code Requirements for Structural Concrete R402.2, R403.1, R404.1.3, R404.1.3.4, R404.1.4.2, R506.1

100735044

REFERENCED STANDARDS

AISI American Iron and Steel Institute 25 Massachusetts Avenue, NW Suite 800 Washington, DC 20001

AISI S100—16: North American Specification for the Design of Cold-formed Steel Structural Members, 2016

R608.9.2, R608.9.3

AISI S220—15: North American Standard for Cold-formed Steel Framing—Nonstructural Members, 2015

R702.3.3

AISI S230—15: Standard for Cold-formed Steel Framing—Prescriptive Method for One- and Two-family Dwellings, 2015

R301.1.1, R301.2.1.1, R301.2.2.7, R301.2.2.8, R603.6, R603.9.4.1, R603.9.4.2, R608.9.2, R608.9.3, Figure 608.9(11), R608.10

AISI S240—15: North American Standard for Cold-Formed Steel Structural Framing

R505.1.3, R603.6, R702.3.3, R804.3.6

ANSI American National Standards Institute

25 West 43rd Street, 4th Floor New York, NY 10036

A108.1A—16: Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar

R702.4.1

A108.1B—99: Installation of Ceramic Tile, Quarry Tile on a Cured Portland Cement Mortar Setting Bed with Dry-set or Latex Portland Mortar

R702.4.1

A108.4—99: Installation of Ceramic Tile with Organic Adhesives or Water-Cleanable Tile-setting Epoxy Adhesive

R702.4.1

A108.5—99: Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex Portland Cement Mortar

R702.4.1

A108.6—99: Installation of Ceramic Tile with Chemical-resistant, Water-cleanable Tile-setting and -grouting Epoxy

R702.4.1

A108.11—99: Interior Installation of Cementitious Backer Units

R702.4.1

ANSI 117—2015: Standard Specifications for Structural Glued Laminated Timber of Softwood Species

R502.1.3, R602.1.3, R802.1.3

A118.1—16: American National Standard Specifications for Dry-set Portland Cement Mortar

R702.4.1

A118.3—13: American National Standard Specifications for Chemical-resistant, Water-cleanable Tile-setting and -grouting Epoxy, and Water-cleanable Tile-setting Epoxy Adhesive

R702.4.1

A118.4—16: American National Standard Specifications for Modified Dry-Set Cement Mortar

R606.2.11

A136.1—08: American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile

R702.4.1

A137.1—17: American National Standard Specifications for Ceramic Tile

R702.4.1

S3.41: American National Standard Audible Evacuation Signal

R325.5.2.1

Z97.1—2014: Safety Glazing Materials Used in Buildings—Safety Performance Specifications and Methods of Test

R308.1.1, R308.3.1, Table R303.3.1(2)

APA APA—The Engineered Wood Association

7011 South 19th Tacoma, WA 98466

ANSI/A190.1—2017: Structural Glued-laminated Timber

R502.1.3, R602.1.3, R802.1.2

ANSI/APA PRP 210—2014: Standard for Performance-rated Engineered Wood Siding

R604.1, Table R703.3(1), R703.3.4

ANSI/APA PRG 320—2017: Standard for Performance-rated Cross Laminated Timber

R502.1.6, R602.1.6, R802.1.6

536 2019 CALIFORNIA RESIDENTIAL CODE

100735044

REFERENCED STANDARDS

APA—continued ANSI/APA PRR 410—2016: Standard for Performance-rated Engineered Wood Rim Boards

R502.1.7, R602.1.7, R802.1.7

ANSI/APA PRS 610.1—2013: Standard for Performance-Rated Structural Insulated Panels in Wall Applications

R602.1.11, R610.3, R610.4

APA E30—15: Engineered Wood Construction Guide

Table R503.2.1.1(1), R503.2.2, R803.2.2, R803.2.3

ASCE/SEI American Society of Civil Engineers

Structural Engineering Institute

1801 Alexander Bell Drive Reston, VA 20191-4400

7—16: Minimum Design Loads and Associated Criteria for Buildings and Other Structures R301.2.1.1, R301.2.1.2, R301.2.1.2.1, R301.2.1.5, R301.2.1.5.1, Table R608.6(1), Table R608.6(2), Table R608.6(3), Table R608.6(4), Table R608.7(1A), Table R608.7(1B), Table R608.7(1C), R608.9.2, R608.9.3, R609.2, R609.6.2

24—14: Flood-resistant Design and Construction R301.2.4, R301.2.4.1, R322.1, R322.1.1, R322.1.6, R322.1.9, R322.2.2, R322.3.3

32—17: Design and Construction of Frost-protected Shallow Foundations R403.1.4.1

ASSE ASSE International 18927 Hickory Creek Drive, Suite 220 Mokena, IL 60448

1051—2009: Performance Requirements for Individual and Branch-type Air Admittance Valves for Plumbing Drainage Systems P3114.1

ASTM ASTM International 100 Barr Harbor Drive, P.O. Box C700 West Conshohocken, PA 19428 A36/A36M—14: Specification for Carbon Structural Steel

R606.15, R608.5.2.2

A53/A53M—12: Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

R407.3

A123/A123M—15: Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products

Table 507.2.3

A153/A153M—09: Specification for Zinc Coating (Hot Dip) on Iron and Steel Hardware

R317.3, Table 507.2.3, Table R606.3.4.1, R703.6.3, R905.7.5, R905.8.6

A167—99(2009): Specification for Stainless and Heat-resisting Chromium-nickel Steel Plate, Sheet and Strip

Table R606.3.4.1

A240/A240M—15A: Standard Specification for Chromium and Chromium-nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications

Table R905.10.3(1)

A307—14: Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength

R608.5.2.2, Table R507.2.3

A463/A463M—15: Standard Specification for Steel Sheet, Aluminum-coated by the Hot-dip Process

Table R905.10.3(2)

A563—15: Standard Specification for Carbon and Alloy Steel Nuts

Table R507.2.3

A615/A615M—2015aE1: Specification for Deformed and Plain Carbon-steel Bars for Concrete Reinforcement

R402.3.1, R403.1.3.5.1, R404.1.3.3.7.1, R608.5.2.1

A641/A641M—09a(2014): Specification for Zinc-coated (Galvanized) Carbon Steel Wire

Table R606.3.4.1

100735044

REFERENCED STANDARDS

ASTM—continued A653/A653M—15: Specification for Steel Sheet, Zinc-coated (Galvanized) or Zinc-iron Alloy-coated (Galvannealed) by the Hot-dip Process

R317.3.1, R505.2.2, Table R507.2.3, R603.2.2, Table R606.3.4.1, R608.5.2.3, R804.2.2, R804.2.3, Table R905.10.3(1), Table R905.10.3(2)

A706/A706M—15: Specification for Low-alloy Steel Deformed and Plain Bars for Concrete Reinforcement

R402.3.1, R403.1.3.5.1, R404.1.3.3.7.1, R608.5.2.1

A755/A755M—2015: Specification for Steel Sheet, Metallic Coated by the Hot-dip Process and Prepainted by the Coil-coating Process for Exterior Exposed Building Products

Table R905.10.3(2)

A792/A792M—10(2015): Specification for Steel Sheet, 55% Aluminum-zinc Alloy-coated by the Hot-dip Process

R505.2.2, R603.2.2, R608.5.2.3, R804.2.2, Table 905.10.3(2)

A875/A875M—13: Specification for Steel Sheet, Zinc-5%, Aluminum Alloy-coated by the Hot-dip Process

R608.5.2.3, Table R905.10.3(2)

A924/A924M—14: Standard Specification for General Requirements for Steel Sheet, Metallic-coated by the Hot-dip Process

Table R905.10.3(1)

A996/A996M—15: Specifications for Rail-steel and Axle-steel Deformed Bars for Concrete Reinforcement

R403.1.3.5.1, R403.2.1, Table R404.1.2(9), R404.1.3.3.7.1, R608.5.2.1, Table R608.5.4(2)

A1003/A1003M—15: Standard Specification for Steel Sheet, Carbon, Metallic and Nonmetallic-coated for Cold-formed Framing Members

R505.2.1, R505.2.2, R603.2.1, R603.2.2, R804.2.1, R804.2.2

B101—12: Specification for Lead-coated Copper Sheet and Strip for Building Construction

Table R905.2.8.2, Table R905.10.3(1)

B209—14: Specification for Aluminum and Aluminum-alloy Sheet and Plate

Table 905.10.3(1)

B370—12: Specification for Copper Sheet and Strip for Building Construction

Table R905.2.8.2, Table R905.10.3(1)

B695—04(2009): Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

R317.3.1, R317.3.3, Table R905.10.(3).2.3

C5—10: Specification for Quicklime for Structural Purposes

R702.2.1

C22/C22M—2015: Specification for Gypsum

R702.2.1, R702.3.1

C27—98(2013): Specification for Standard Classification of Fireclay and High-alumina Refractory Brick

R1001.5

C28/C28M—10(2015): Specification for Gypsum Plasters

R702.2.1

C33/C33M—13: Specification for Concrete Aggregates

R403.4.1

C34—13; Specification for Structural Clay Load-bearing Wall Tile

Table R301.2(1), R606.2.2

C35/C35M—(2014): Specification for Inorganic Aggregates for Use in Gypsum Plaster

R702.2.1

C55—2014A: Specification for Concrete Building Brick

R202, Table R301.2(1), R606.2.1

C56—13: Standard Specification for Structural Clay Nonloadbearing Tile

R606.2.2

C59/C59M—00(2015): Specification for Gypsum Casting Plaster and Molding Plaster

R702.2.1

C61/C61M—00(2015): Specification for Gypsum Keene’s Cement

R702.2.1

C62—13A: Standard Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)

R202, Table R301.2(1), R606.2.2

C73—14: Specification for Calcium Silicate Face Brick (Sand Lime Brick)

R202, Table R301.2(1), R606.2.1

C90—14: Specification for Load-bearing Concrete Masonry Units

Table R301.2(1), 606.2.1

538 2019 CALIFORNIA RESIDENTIAL CODE

100735044

REFERENCED STANDARDS

ASTM—continued C91/C91M—12: Specification for Masonry Cement

R702.2.2, R703.7.2

C94/C94M—15A: Standard Specification for Ready-mixed Concrete

R404.1.3.3.2, R608.5.1.2

C126—15: Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

R606.2.2

C129—14A: Specification for Nonload-bearing Concrete Masonry Units

Table R301.2(1)

C143/C143M—15: Test Method for Slump of Hydraulic Cement Concrete

R404.1.3.3.4, R608.5.1.4

C145—85: Specification for Solid Load-bearing Concrete Masonry Units

R202, Table R301.2(1)

C150/C150M—15: Specification for Portland Cement

R608.5.1.1, R702.7.2

C199—84(2011): Test Method for Pier Test for Refractory Mortar

R1001.5, R1001.8, R1003.12

C203—05a(2012): Standard Test Methods for Breaking Load and Flexural Properties of Block-type Thermal Insulation

Table R610.3.1

C207—06(2011): Specification for Hydrated Lime for Masonry Purposes

Table R606.2.8

C208—12: Specification for Cellulosic Fiber Insulating Board

R602.1.10, Table R602.3(1), Table R906.2

C212—14: Standard Specification for Structural Clay Facing Tile

R602.2.2

C216—15: Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

R202, Table R301.2(1), R606.2.2

C270—14A: Specification for Mortar for Unit Masonry

R606.2.8, Table R606.2.8, R606.2.11

C315—07(2011): Specification for Clay Flue Liners and Chimney Pots

R1001.8, R1003.11.1, Table 1003.14(1)

C406/C406M—2015: Specifications for Roofing Slate

R905.6.4

C475/C475M—15: Specification for Joint Compound and Joint Tape for Finishing Gypsum Wallboard

R702.3.1

C476—10: Specification for Grout for Masonry

R606.2.12

C503/C503M—2010: Standard Specification for Marble Dimension Stone

R606.2.4

C514—04(2014): Specification for Nails for the Application of Gypsum Wallboard

R702.3.1

C552—15: Standard Specification for Cellular Glass Thermal Insulation

Table R906.2

C557—03(2009)e01: Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing

R702.3.1.1

C568/C568M—2010: Standard Specification for Limestone Dimension Stone

R606.2.4

C578—15: Specification for Rigid, Cellular Polystyrene Thermal Insulation

R316.8, R403.3, Table 703.8.4(2), Table R703.15.1, Table R703.15.2, Table R703.16.1, Table R703.16.2, Table R906.2

C587—04(2014): Specification for Gypsum Veneer Plaster

R702.2.1

C595/C595M—14E1: Specification for Blended Hydraulic Cements

R608.5.1.1, R702.2.2, R703.7.2

C615/C615M—11: Standard Specification for Granite Dimension Stone

R606.2.4

100735044

REFERENCED STANDARDS

ASTM—continued C616/C616M—10: Standard Specification for Quartz-based Dimension Stone

R606.2.4

C629/C629M—10: Standard Specification for Slate Dimension Stone

R606.2.4

C631—09(2014): Specification for Bonding Compounds for Interior Gypsum Plastering

R702.2.1

C645—14: Specification for Nonstructural Steel Framing Members

R702.3.3

C652—15: Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)

R202, Table R301.2(1), R606.2.2

C685/C685M—14: Specification for Concrete Made by Volumetric Batching and Continuous Mixing

R404.1.3.3.2, R608.5.1.2

C726—12: Standard Specification for Mineral Wool Roof Insulation Board

Table R906.2

C728—15: Standard Specification for Perlite Thermal Insulation Board

Table R906.2

C744—14: Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units

R606.2.1

C836/C836M—15: Specification for High Solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

R905.15.2

C841—03(2013): Standard Specification for Installation of Interior Lathing and Furring

R702.2.1

C842—05(2015): Standard Specification for Application of Interior Gypsum Plaster

R702.2.1

C843—99(2012): Specification for Application of Gypsum Veneer Plaster

R702.2.1

C844—2015: Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster

R702.2.1

C847—14A: Specification for Metal Lath

R702.2.1, R702.2.2

C887—13: Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar

R406.1, R606.2.9

C897—15: Specification for Aggregate for Job-mixed Portland Cement-based Plasters

R702.2.2

C920—14A: Standard Specification for Elastomeric Joint Sealants

R406.4.1

C926—15B: Specification for Application of Portland Cement-based Plaster

R702.2.2, R702.2.2.1, R703.7, R703.7.2, R703.7.2.1, R703.7.4

C933—14: Specification for Welded Wire Lath

R702.2.1, R702.2.2

C946—10: Standard Practice for Construction of Dry-Stacked, Surface-Bonded Walls

R606.2.9

C954—15: Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in (0.84 mm) or to 0.112 in. (2.84 mm) in Thickness

R505.2.5, R603.2.5, R702.3.5.1, R804.2.5

C957/C957M—15: Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Integral Wearing Surface

R905.15.2

C1002—14: Specification for Steel Self-piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs

R702.3.1, R702.3.5.1

C1029—15: Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation

R905.14.2

540 2019 CALIFORNIA RESIDENTIAL CODE

100735044

REFERENCED STANDARDS

ASTM—continued C1032—14: Specification for Woven Wire Plaster Base

R702.2.1, R702.2.2

C1047—14a: Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base

R702.2.1, R702.2.2, R702.3.1

C1063—15A: Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster

R702.2.2, R703.7, R703.7.1

C1088—14: Standard Specification for Thin Veneer Brick Units Made from Clay or Shale

R606.2.2

C1107/C1107M—14A: Standard Specification for Packaged Dry, Hydraulic-cement Grout (Nonshrink)

R402.3.1

C1116/C116M—10(2015): Standard Specification for Fiber-reinforced Concrete and Shotcrete

R402.3.1

C1157—11/C1157M—11: Standard Performance Specification for Hydraulic Cement

R608.5.1.1, R703.7.2

C1167—11: Specification for Clay Roof Tiles

R905.3.4

C1177/C1177M—13: Specification for Glass Mat Gypsum Substrate for Use as Sheathing

R702.3.1, Table 906.2

C1178/C1178M—13: Specification for Glass Mat Water-resistant Gypsum Backing Panel

R702.3.1, R702.3.7, Table R702.4.2

C1186—08(2012): Specification for Flat Fiber Cement Sheets

R703.10.1, R703.10.2

C1261—13: Specification for Firebox Brick for Residential Fireplaces

R1001.5, R1001.8

C1278/C1278M—07a(2011): Specification for Fiber-reinforced Gypsum Panels

R702.3.1, R702.3.7, Table R702.4.2, Table R906.2

C1283—11: Practice for Installing Clay Flue Lining

R1003.9.1, R1003.12

C1288—14: Standard Specification for Discrete Nonasbestos Fiber-cement Interior Substrate Sheets

Table R503.2.1.1(1), Table R503.2.1.1(2), Table 602.3(2), Table R702.4.2

C1289—15: Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board

R316.8, Table R703.15.1, Table R703.15.2, Table R703.16.1, Table R703.16.2, R708.8.4(2), Table R906.2

C1325—14: Standard Specification for Nonasbestos Fiber-mat Reinforced Cement Interior Substrate Sheets Backer Units

Table R702.4.2

C1328/C1328M—12: Specification for Plastic (Stucco) Cement

R702.2.2, R703.7.2

C1364—10B: Standard Specification for Architectural Cast Stone

R606.2.5

C1396/C1396M—2014A: Specification for Gypsum Board

Table R602.3(1), R702.2.1, R702.2.2, R702.3.1, R702.3.7

C1405—15: Standard Specification for Glazed Brick (Single Fired, Brick Units)

R606.2.2

C1492—03(2009): Specification for Concrete Roof Tile

R905.3.5

C1513—201: Standard Specification for Steel Tapping Screws for Cold-formed Steel Framing Connections

R505.2.5, R603.2.5, R702.3.5.1, Table R703.3(2), Table R703.16.1, Table R703.16.2, R804.2.5

C1634—15: Standard Specification for Concrete Facing Brick

R606.2.1

C1658/C1658M—13: Standard Specification for Glass Mat Gypsum Panels

R702.3.1

C1670/1670M—16: Standard Specification for Adhered Manufactured Stone Masonry Veneer Units

R606.2.6

C1691—11: Standard Specification for Unreinforced Autoclaved Aerated Concrete (AAC) Masonry Units

R606.2.3

100735044

REFERENCED STANDARDS

ASTM—continued C1693—11: Standard Specification for Autoclaved Aerated Concrete (AAC)

R606.2.3

C1766—13: Standard Specification for Factory-Laminated Gypsum Panel Products

R702.3.1

D41/D41M—2011: Specification for Asphalt Primer Used in Roofing, Dampproofing and Waterproofing

Table R905.9.2, Table R905.11.2

D43/D43M—2000(2012)E1: Specification for Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing

Table R905.9.2

D226/D226M—09: Specification for Asphalt-saturated (Organic Felt) Used in Roofing and Waterproofing

R703.2, R905.1.1, Table R905.1.1(1), R905.8.4, Table R905.9.2

D227/D227M—03(2011)e1: Specification for Coal Tar Saturated (Organic Felt) Used in Roofing and Waterproofing

Table R905.9.2

D312/D321M—15: Specification for Asphalt Used in Roofing

Table R905.9.2

D422—63(2007)E2: Test Method for Particle-size Analysis of Soils

R403.1.8.1

D449/D449M—03(2014)E1: Specification for Asphalt Used in Dampproofing and Waterproofing

R406.2

D450/D450M—07(2013)E1: Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing

Table R905.9.2

D1227—13: Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

Table R905.9.2, Table R905.11.2, R905.15.2

D1863/D1863M—05(2011)e1: Specification for Mineral Aggregate Used in Built-up Roofs

Table R905.9.2

D1970/D1970M—2015A: Specification for Self-adhering Polymer Modified Bitumen Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection

R905.1.1, R905.2.8.2, R905.11.2.1

D2178/D2178M—15: Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

Table R905.9.2

D2626/D2626M—04 (2012)e1: Specification for Asphalt-saturated and Coated Organic Felt Base Sheet Used in Roofing

Table R905.1.1(1), Table R905.9.2

D2822/D2822M—05(2011)e1: Specification for Asphalt Roof Cement, Asbestos Containing

Table R905.9.2

D2823/D2823M—05(2011)e1: Specification for Asphalt Roof Coatings, Asbestos Containing

Table R905.9.2

D2824/D2824M—2013: Specification for Aluminum-pigmented Asphalt Roof Coatings, Nonfibered, Asbestos Fibered and Fibered without Asbestos

Table R905.9.2, Table R905.11.2

D2898—10: Test Methods for Accelerated Weathering of Fire-retardant-treated Wood for Fire Testing

R802.1.5.4, R802.1.5.8

D3019—08: Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and Nonasbestos Fibered

Table R905.9.2, Table R905.11.2

D3161/D3161M—15: Test Method for Wind-Resistance of Steep Slope Roofing Products (Fan Induced Method)

R905.2.4.1, Table R905.2.4.1, R905.16.6

D3201/D3201M—2013: Test Method for Hygroscopic Properties of Fire-retardant Wood and Wood-base Products

R802.1.5.9

D3462/D3462M—10A: Specification for Asphalt Shingles Made From Glass Felt and Surfaced with Mineral Granules

R905.2.4

D3468/D3468M—99(2013)E1: Specification for Liquid-applied Neoprene and Chlorosulfanated Polyethylene Used in Roofing and Waterproofing

R905.15.2

D3679—13: Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding

R703.11

542 2019 CALIFORNIA RESIDENTIAL CODE

100735044

REFERENCED STANDARDS

ASTM—continued D3737—2012: Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)

R502.1.3, R602.1.3, R802.1.2

D3747—79(2007): Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation

Table R905.9.2, Table R905.11.2

D3909/D3909M—14: Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules

R905.2.8.2, R905.5.4, Table R905.9.2

D4022/D4022M—2007(2012)e1: Specification for Coal Tar Roof Cement, Asbestos Containing

Table R905.9.2

D4318—10E1: Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils

R403.1.8.1

D4434/D4434M—12: Specification for Poly (Vinyl Chloride) Sheet Roofing

R905.13.2

D4479/D4479M—07(2012)e1: Specification for Asphalt Roof Coatings—asbestos-free

Table R905.9.2

D4586/D4586M—07(2012)e1: Specification for Asphalt Roof Cemen—asbestos-free

Table R905.9.2

D4601/D4601M—04(2012)e1: Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing

Table R905.9.2, R905.11.2.1

D4637/D4637M—14E1: Specification for EPDM Sheet Used in Single-ply Roof Membrane

R905.12.2

D4829—11: Test Method for Expansion Index of Soils

R403.1.8.1

D4869/D4869M—15: Specification for Asphalt-saturated (Organic Felt) Underlayment Used in Steep Slope Roofing

R905.1.1, Table R905.1.1(1)

D4897/D4897M—01(2009): Specification for Asphalt Coated Glass-fiber Venting Base Sheet Used in Roofing

Table R905.9.2

D4990—1997a(2013): Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing

Table R905.9.2

D5019—07a: Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane

R905.12.2

D5055—13E1: Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists

R502.1.2, R802.1.8

D5456—14B: Standard Specification for Evaluation of Structural Composite Lumber Products

R502.1.5, R602.1.5, R802.1.4

D5516—09: Test Method for Evaluating the Flexural Properties of Fire-retardant-treated Softwood Plywood Exposed to the Elevated Temperatures

R802.1.5.6

D5643/D5643M—06(2012)e1: Specification for Coal Tar Roof Cement Asbestos-free

Table R905.9.2

D5664—10: Test Methods For Evaluating the Effects of Fire-retardant Treatments and Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber

R802.1.5.7

D5665/D5665M—99a(2014)E1: Specification for Thermoplastic Fabrics Used in Cold-applied Roofing and Waterproofing

Table R905.9.2

D5726—98(2013): Specification for Thermoplastic Fabrics Used in Hot-applied Roofing and Waterproofing

Table R905.9.2

D6083—05e01: Specification for Liquid-applied Acrylic Coating Used in Roofing

Table R905.9.2, Table R905.11.2, Table R905.14.3, R905.15.2

D6162/D6162M—2000a(2015)E1: Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

Table R905.11.2

D6163/D6163M—2000(2015)E1: Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

Table R905.11.2

100735044

REFERENCED STANDARDS

ASTM—continued D6164/D6164M—11: Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements

Table R905.11.2

D6222/D6222M—11: Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements

Table R905.11.2

D6223/D6223M—02(2009)E1: Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcement

Table R905.11.2

D6298—13: Specification for Fiberglass-reinforced Styrene Butadiene Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface

Table R905.11.2

D6305—08(2015)E1: Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing

R802.1.5.6

D6380/D6380—03(2013)E1: Standard Specification for Asphalt Roll Roofing (Organic Felt)

Table R905.1.1(1), R905.2.8.2, R905.5.4

D6464—03a(2009)e1: Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing

R702.3.1.1

D6694/D6694M—08(2013)E1: Standard Specification for Liquid-applied Silicone Coating Used in Spray Polyurethane Foam Roofing Systems

Table R905.14.3, R905.15.2

D6754/D6754M—10: Standard Specification for Ketone-ethylene-ester-based Sheet Roofing

R905.13.2

D6757—2013: Specification for Underlayment Felt Containing Inorganic Fibers Used with Steep Slope Roofing

Table R905.1.1(1), R905.1.1

D6841—08: Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant-treated Lumber

R802.1.5.7

D6878/D6878M—13: Standard Specification for Thermoplastic-polyolefin-based Sheet Roofing

R905.13.2

D6947/D6947M—07(2013)E1: Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System

Table R905.14.3, R905.15.2

D7032—14: Standard Specification for Establishing Performance Ratings for Wood-plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)

R507.2.2, R507.2.2.1, 507.2.2.3, 507.2.2.4

D7158—D7158M—2016: Standard Test Method for Wind Resistance of Asphalt Shingles (Uplift Force/Uplift Resistance Method)

R905.2.4.1, Table R905.2.4.1

D7254—15: Standard Specification for Polypropylene (PP) siding

Table R703.3(1), R703.14

D7425/D7425M—13: Standard Specification for Spray Polyurethane Foam Used for Roofing Application

R905.14.2

D7672—14: Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies

R502.1.7, R602.1.7, R802.1.7

D7793—13: Standard Specification for Insulated Vinyl Siding

R703.13, Table R703.3(1)

E84—2016: Standard Test Method for Surface Burning Characteristics of Building Materials

R202, R302.9.3, R302.9.4, R302.10.1, R302.10.2, R316.3, R316.5.9, R316.5.11, R507.2.2.2, R703.14.3, R802.1.5

E96/E96M—2015: Test Method for Water Vapor Transmission of Materials

R202, Table R806.5

E108—2016: Test Methods for Fire Tests of Roof Coverings

R302.2.4, R902.1

E119—2016: Test Methods for Fire Tests of Building Construction and Materials

Table R302.1(1), Table R302.1(2), R302.2.1, R302.2.2, R302.3, R302.4.1, R302.11.1, R606.2.2

544 2019 CALIFORNIA RESIDENTIAL CODE

100735044

REFERENCED STANDARDS

ASTM—continued E136—2016: Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C

R202, R302.11

E283—04(2012): Test Method for Determining the Rate of Air Leakage through Exterior Windows, Curtain Walls and Doors under Specified Pressure Differences Across the Specimen

R202

E330/E330M—14: Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference

R609.4, R609.5, R609.6.2, R703.1.2

E331—00(2009): Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference

R703.1.1

E814—2013A: Standard Test Method for Fire Tests of Penetration Firestop Systems

R302.4.1.2

E970—14: Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source

R302.10.5

E1602—03(2010)e1: Guide for Construction of Solid Fuel Burning Masonry Heaters

R1002.2

E1886—13A: Test Method for Performance Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials

R301.2.1.2, R609.6.1, R609.6.2, Table R703.11.2

E1996—2014a: Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

R301.2.1.2, R301.2.1.2.1, R609.6.1, R609.6.2

E2178—2013: Standard Test Method for Air Permeance of Building Materials

R202

E2273—03(2011): Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies

R703.9.2

E2568—09e1: Standard Specification for PB Exterior Insulation and Finish Systems

R703.9.1, R703.9.2

E2570/E2570M—07(2014)E1: Standard Test Methods for Evaluating Water-resistive Barrier (WRB) Coatings Used Under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage

R703.9.2

E2632/E2632M—2013e1: Standard Test Method for Evaluating the Under-Deck Fire Test Response of Deck Materials:

R337.9.3, R337.9.4, R337.9.4.1, R337.9.5

E2634—11(2015): Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems

R404.1.3.3.6.1, R608.4.4

E2707—2015: Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure

R337.7.3, R337.7.3.1, R337.8.3

E2726/E2726M—2012a: Standard Test Method for Evaluating the Fire-Test-Response of Deck Structures to Burning Brands

R337.9.3, R337.9.4, R337.9.4.2

E2886/E2886M—2014: Standard Test Method for Evaluating the Ability of Exterior Vents to Resist the Entry of Embers and Direct Flame Impingent

R337.6.2, R337.6.3

**_ASTM E2886, Amended Sections as follows:_* Revise Sections 10.1.8.3, 10.1.8.4, and 10.1.8.5 as follows: 10.1.8.3 Report the temperatures of the unexposed temperatures on the unexposed side of the vent during the entire optional Insulation Test of the Flame Intrusion. 10.1.8.4 The maximum temperature reached during the test by any one of the unexposed surface thermocouples during the entire optional Insulation Test of the Flame Intrusion Test. 10.1.8.5 The maximum average temperature reached during the test by all of the unexposed surface thermocouples during the entire optional Insulation Test of the Flame Intrusion Test.

100735044

REFERENCED STANDARDS

ASTM—continued E2957—2015: Standard Test Method for Resistance to Wildfire Penetration of Eaves, Soffits and Other Projections

R337.7.5, R337.7.6, R337.7.8, R337.7.10

**_ASTM E2957, Amended Sections as follows:_* Add new Section 12.5 as follows:

12.5 Conditions of Acceptance:¶

Should one of the three replicates fail to meet the Conditions of Acceptance, three additional tests may be run. All of the additional tests must meet the Conditions of Acceptance.

1. Absence of flame penetration of the eaves or horizontal projection assembly at any time. 2. Absence of structural failure of the eaves or horizontal projection subassembly at any time. 3. Absence of sustained combustion of any kind at the conclusion of the 40-minute test. F844—07a(2013): Standard Specification for Washers, Steel, Plain (Flat), Unhardened for General Use

Table R507.2.3

F1554—15: Specification for Anchor Bolts, Steel, 36, 55 and 105-ksi Yield Strength

R608.5.2.2

F1667—15: Specification for Driven Fasteners, Nails, Spikes and Staples

R317.3, Table R507.2.3, Table R602.3(1), R703.3.3, R703.6.3, Table R703.15.1, Table R703.15.2, R905.2.5

F2090—17: Specification for Window Fall Prevention Devices with Emergency Escape (Egress) Release Mechanisms

R310.1.1, R312.2.1, R312.2.2

AWC American Wood Council 222 Catocin Circle, Suite 201 Leesburg, VA 20175

AWC STJR—2015: Span Tables for Joists and Rafters

R502.3, R802.4, R802.5

AWC WFCM—2015: Wood Frame Construction Manual for One- and Two-family Dwellings

R301.1.1, R301.2.1.1, R602.10.8.2, R608.9.2, Figure R608.9(9), R608.10

ANSI AWC NDS—2015: National Design Specification (NDS) for Wood Construction—with 2015 NDS Supplement

R404.2.2, R502.2, Table R503.1, R602.3, R608.9.2, Table R703.15.1, Table R703.15.2, R802.2

ANSI AWC PWF—2015: Permanent Wood Foundation Design Specification

R317.3.2, R401.1, R404.2.3

AWPA American Wood Protection Association

P.O. Box 361784 Birmingham, AL 35236-1784

C1—03: All Timber Products—Preservative Treatment by Pressure Processes

R902.2

M4—11: Standard for the Care of Preservative-treated Wood Products

R317.1.1, R318.1.2

U1—14: USE CATEGORY SYSTEM: User Specification for Treated Wood Except Section 6 Commodity Specification H

R317.1, R402.1.2, R504.3, R703.6.3, R905.7.5, Table R905.8.5, R905.8.6

CEN European Committee for Standardization (EN)

Central Secretariat Rue de Stassart 36 B-10 50 Brussels EN 15250-2007: Slow Heat Release Appliances Fired by Solid Fuel Requirements and Test Methods

R1002.2

546 2019 CALIFORNIA RESIDENTIAL CODE

100735044

REFERENCED STANDARDS

CPA Composite Panel Association 19465 Deerfield Avenue, Suite 306 Leesburg, VA 20176

ANSI A135.4—2012: Basic Hardboard

Table R602.3(2)

ANSI A135.5—2012: Prefinished Hardboard Paneling

R702.5

ANSI A135.6—2012: Engineered Wood Siding

R703.5

ANSI A135.7—2012: Engineered Wood Trim

R703.5

A208.1—2016: Particleboard

R503.3.1, R602.1.9, R605.1

CPSC Consumer Product Safety Commission

4330 East-West Highway Bethesda, MD 20814

16 CFR, Part 1201—(2002): Safety Standard for Architectural Glazing R308.1.1, R308.3.1, Table R308.3.1(1)

16 CFR, Part 1209—(2002): Interim Safety Standard for Cellulose Insulation R302.10.3

16 CFR, Part 1404—(2002): Cellulose Insulation R302.10.3

CSA CSA Group 8501 East Pleasant Valley Road Cleveland, OH 44131-5516

AAMA/WDMA/CSA 101/I.S.2/A440—17: North American Fenestration Standard/Specification for Windows, Doors and Unit Skylights

R308.6.9, R609.3

ASME A17.1/CSA B44—2016: Safety Code for Elevators and Escalators

R321.1

B44—2013: Safety Code for Elevators and Escalators

R321.1

CSA O325—07: Construction Sheathing

R503.2.1, R602.1.8, R604.1, R803.2.1

O437-Series—93: Standards on OSB and Waferboard (Reaffirmed 2006)

R503.2.1, R602.1.8, R604.1, R803.2.1

CSSB Cedar Shake & Shingle Bureau

P.O. Box 1178 Sumas, WA 98295-1178

CSSB—97: Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau

R702.6, R703.6

DASMA Door and Access Systems Manufacturers Association International

1300 Summer Avenue Cleveland, OH 44115-2851

108—2017: Standard Method for Testing Garage Doors, Rolling Doors and Flexible Doors; Determination of Structural Performance Under Uniform Static/Air Pressure Difference

R609.4

115—2016: Standard Method for Testing Sectional Garage Doors, Rolling Doors and Flexible Doors: Determination of Structural Performance Under Missile Impact and Cyclic Wind Pressure

R301.2.1.2

100735044

REFERENCED STANDARDS

DOC United States Department of Commerce

1401 Constitution Avenue, NW Washington, DC 20230

PS 1—09: Structural Plywood

R404.2.1, Table R404.2.3, R503.2.1, R602.1.8, R604.1, R803.2.1

PS 2—10: Performance Standard for Wood-based Structural-use Panels

R404.2.1, Table R404.2.3, R503.2.1, R602.1.8, R604.1, R803.2.1

PS 20—05: American Softwood Lumber Standard

R404.2.1, R502.1.1, R602.1.1, R802.1.1

FEMA Federal Emergency Management Agency

500 C Street SW Washington, DC 20472

FEMA TB-2—08: Flood Damage-resistant Materials Requirements

R322.1.8

FEMA TB-11—01: Crawlspace Construction for Buildings Located in Special Flood Hazard Area

R408.7

FM FM Approvals Headquarters Office 1151 Boston-Providence Turnpike P.O. Box 9102 Norwood, MA 02062

4450—(1989): Approval Standard for Class 1 Insulated Steel Deck Roofs—with Supplements through July 1992 R906.1

4880—(2015): Approval Standard for Class 1 Rating of Building Panels or Interior Finish Materials R316.6

GA Gypsum Association 6525 Belcrest Road, Suite 480 Hyattsville, MD 20782

GA-253—2016: Application of Gypsum Sheathing

Table R602.3(1)

HPVA Hardwood Plywood & Veneer Association

1825 Michael Faraday Drive Reston, Virginia 20190

ANSI/HPVA HP-1—2016: American National Standard for Hardwood and Decorative Plywood

R702.5

ICC International Code Council, Inc.

500 New Jersey Avenue NW 6th Floor Washington, DC 20001

ICC/ANSI A117.1—09: Accessible and Usable Buildings and Facilities

R321.3 ICC—ES EG107: Evaluation guideline for determination of Volatile Organic Compound (voc) content

R902

ICC 400—17: Standard on the Design and Construction of Log Structures

R301.1.1, R502.1.4, R602.1.4, R703.1, R802.1.3

ICC 500—14: ICC/NSSA Standard on the Design and Construction of Storm Shelters

R323.1

ICC 600—14: Standard for Residential Construction in High-wind Regions

R301.2.1.1

548 2019 CALIFORNIA RESIDENTIAL CODE

100735044

REFERENCED STANDARDS

ICC—continued IEBC—18: International Existing Building Code®

R110.2

IFC—18: International Fire Code

R102.7

ISO International Organization for Standardization

Chemin de Blandonnet 8

CP 401 1214 Vernier Geneva, Switzerland

8336—2009: Fibre-cement Flat Sheets-product Specification and Test Methods Table R503.2.1.1(1), Table R503.2.1.1(2), Table R602.3(2), Table R702.4.2, R703.10.1, R703.10.2

NFPA National Fire Protection Association

1 Batterymarch Park Quincy, MA 02169-7471

13—16: Standard for Installation of Sprinkler Systems _as amended_* R302.3 See CCR, Title 24 Part 2 California Building Code, Chapter 35 or CCR, Title 24, Part 9 California Fire Code, Chapter 80 for amendments to NFPA 13.

13D—16: Standard for the Installation of Sprinkler Systems in One- and Two-family Dwellings and Manufactured Homes _as amended_* R313.1.1, R313.2.1, R324.6.2.1

**_NFPA 13D, Amended Sections as follows:_* Revise Section 6.2.2 to read as follows: 6.2.2 Where a well, pump, tank or combination thereof is the source of supply for a fire sprinkler system , the configuration for the system shall be one of the following:

(1) The water supply shall serve both domestic and fire sprinkler systems,

( a ) A test connection shall be provided downstream of the pump that creates a flow of water equal to the smallest sprinkler on the system. The connection shall return water to the tank. (b) Any disconnecting means for the pump shall be approved. (c) A method for refilling the tank shall be piped to the tank. (d) A method of seeing the water level in the tank shall be provided without having to open the tank. (e) The pump shall not be permitted to sit directly on the floor. (2) A stand-alone tank is permitted if the following conditions are met:

(a) The pump shall be connected to a 220-volt circuit breaker shared with a common household appliance (e.g., range, oven, dryer), (b) The pump shall be a stainless steel 240-volt pump, (c) A valve shall be provided to exercise the pump. The discharge of the exercise valve shall drain to the tank, and (d) A sign shall be provided stating “Valve must be opened monthly for 5 minutes.” (e) A means for automatically refilling the tank level, so that the tank capacity will meet the required water supply duration in minutes, shall be provided. (f) A test connection shall be provided downstream of the pump that creates a flow of water equal to the smallest sprinkler on the system. The connection may return water to the tank. (g) Any disconnecting means for the pump shall be approved. (h) A method for refilling the tank shall be piped to the tank. (i) A method of seeing the water level in the tank shall be provided without having to open the tank. (j) The pump shall not be permitted to sit directly on the floor. Add new Section 6.2.2.1 to read as follows: 6.2.2.1 Where a fire sprinkler system is supplied by a stored water source with an automatically operated means of pressurizing the system other than an electric pump, the water supply may serve the sprinkler system only. Add new Section 6.2.4 to read as follows: 6.2.4 Where a water supply serves both domestic and fire sprinkler systems, 5 gpm (19 L/min) shall be added to the sprinkler sys- tem demand at the point where the systems are connected, to determine the size of common piping and the size of the total water supply requirements where no provision is made to prevent flow into the domestic water system upon operation of a sprinkler. For multipurpose piping systems, the 5 gpm (19 L/min) demand shall be added at the domestic connection nearest the design area. This demand may be split between two domestic connections at 2.5 gpm (10 L/min) each.

100735044

REFERENCED STANDARDS

NFPA—continued Revise Section 8.3.4 to read as follows: _8.3.4_* Sprinklers shall not be required in detached garages, open attached porches, carports with no habitable space above, and similar structures. Revise Section 8.3.4 to read as follows: _8.3.4_* Sprinklers shall not be required in detached garages, open attached porches, carports with no habitable space above, and similar structures. Add new Section 8.3.10 and 8.3.10.1 as follows: 8.3.10 Solar photovoltaic panel structures 8.3.10.1 Sprinklers shall be permitted to be omitted from the following structures: (1) Solar photovoltaic panel structures with no use underneath. Signs may be provided, as determined by the enforcing agency prohibiting any use underneath including storage. (2) Solar photovoltaic (PV) panels supported by framing that have sufficient uniformly distributed and unobstructed openings throughout the top of the array (horizontal plane) to allow heat and gases to escape, as determined by the enforcing agency. 13R—16: Standard for the Installation of Sprinkler Systems in Low-Rise Residential Occupancies R325.5

72—16: National Fire Alarm and Signaling Code _as amended_* R314.1, R314.7.1

**_NFPA 72, Amended Sections as follows:_* Revise Section 10.3.1 to read as follows: 10.3.1 Equipment constructed and installed in conformity with this code shall be listed for the purpose for which it is used. Fire alarm systems and components shall be California State Fire Marshal approved and listed in accordance with California Code of Regulations, Title 19, Division 1. Revise Section 10.3.3 to read as follows: 10.3.3 All devices and appliances that receive their power from the initiating device circuit or signaling line circuit of a control unit shall be California State Fire Marshal listed for use with the control unit. Revise Section 10.7.1 to read as follows: 10.7.1 Where approved by the authority having jurisdiction, ECS priority signals when evaluated by stakeholders through risk analysis in accordance with 24.3.11 shall be permitted to take precedence over all other signals. Revise Section 12.3.8.1 to read as follows: 12.3.8.1 The outgoing and return (redundant) circuit conductors shall be permitted in the same cable assembly (i.e., multiconduc- tor cable), enclosure, or raceway only under the following conditions:

(1) For a distance not to exceed 10 ft (3.0 m) where the outgoing and return conductors enter or exit the initiating device, noti- fication appliance, or control unit enclosures (2) Single drops installed in the raceway to individual devices or appliances (3)*In a single room not exceeding 1000 ft2 (93 m2) in area, a drop installed in the raceway to multiple devices or appliances

that does not include any emergency control function devices (4) Where the vertically run conductors are contained in a 2-hour rated cable assembly, or enclosed (installed) in a 2-hour rated enclosure or a listed circuit integrity (C.I.) cable, which meets or exceeds a 2-hour fire resistive rating. Revise Section 14.4.6.1 to read as follows: 14.4.6.1 Testing. Household fire alarm systems shall be tested in accordance with the manufacturer’s published instructions according to the methods of Table 14.4.3.2. Revise Section 17.15 to read as follows:

17.15 Fire Extinguisher Electronic Monitoring Device.¶

A fire extinguisher electronic monitoring device shall indicate those con- ditions for a specific fire extinguisher required by California Code of Regulations, Title 19, Division 1, Chapter 1, Section 574.2 (c) and California Fire Code to a fire alarm control unit. Revise Section 21.3.6 to read as follows: 21.3.6 Smoke detectors shall not be installed in unsprinklered elevator hoistways unless they are installed to activate the elevator hoistway smoke relief equipment or where required by Chapter 30 of the California Building Code. Revise Section 23.8.5.1.2 to read as follows: 23.8.5.1.2 Where connected to a supervising station, fire alarm systems employing automatic fire detectors or waterflow detection devices shall include a manual fire alarm box to initiate a signal to the supervising station.

Exception: Fire alarm systems dedicated to elevator recall control, and supervisory service and fire sprinkler monitoring as permitted in Section 21.3 of NFPA 72. Revise Section 23.8.5.4.1 to read as follows: 23.8.5.4.1 Systems equipped with alarm verification features shall be permitted under the following conditions: (1) The alarm verification feature is not initially enabled unless conditions or occupant activities that are expected to cause nuisance alarms are anticipated in the area that is protected by the smoke detectors. Enabling of the alarm verification feature shall be protected by password or limited access.

550 2019 CALIFORNIA RESIDENTIAL CODE

100735044

REFERENCED STANDARDS

NFPA—continued (2) A smoke detector that is continuously subjected to a smoke concentration above alarm threshold does not delay the system functions of Sections 10.7 through 10.16, 23.8.1.1, or 21.2.1 by more than 30 seconds. (3) Actuation of an alarm-initiating device other than a smoke detector causes the system functions of Sections 10.7 through 10.16, 23.8.1.1, or 21.2.1 without additional delay. (4) The current status of the alarm verification feature is shown on the record of completion (see Figure 7.8.2(a), item 4.3). (5) Operation of a patient room smoke detector in I-2 and R-2.1 Occupancies shall not include an alarm verification feature. Revise Section 29.3.1 to read as follows: 29.3.1 All devices, combinations of devices, and equipment to be installed in conformity with this chapter shall be approved and listed by the California State Fire Marshal for the purposes for which they are intended. Revise Section 29.5.2.1.1 to read as follows: _29.5.2.1.1 Smoke and Heat Alarms._* Unless exempted by applicable laws, codes, or standards, smoke or heat alarms used to pro- vide a fire-warning function, and when two or more alarms are installed within a dwelling unit, suite of rooms, or similar area, shall be arranged so that the operation of any smoke or heat alarm causes all alarms within these locations to sound.

Note: Exception to 29.5.2.1.1 not adopted by the SFM Add Section 29.7.2.1 to read as follows: 29.7.2.1 The alarm verification feature shall not be used for household fire warning equipment. Add Section 29.7.6.7.1 to read as follows: 29.7.6.7.1 The alarm verification feature shall not be used for household fire warning equipment. Revise Section 23.8.3.4 to read as follows: 29.8.3.4 Specific location requirements. The installation of smoke alarms and smoke detectors shall comply with the following requirements:

e used for household fire warning equipment._** Add Section 29.7.6.7.1 to read as follows: 29.7.6.7.1 The alarm verification feature shall not be used for household fire warning equipment. Revise Section 23.8.3.4 to read as follows: 29.8.3.4 Specific location requirements. The installation of smoke alarms and smoke detectors shall comply with the following requirements:

(1) Smoke alarms and smoke detectors shall not be located where ambient conditions, including humidity and temperature, are outside the limits specified by the manufacturer's published instructions. (2) Smoke alarms and smoke detectors shall not be located within unfinished attics or garages or in other spaces where tem- peratures can fall below 40ºF (4ºC) or exceed 100ºF (38ºC). (3) Where the mounting surface could become considerably warmer or cooler than the room, such as a poorly insulated ceil- ing below an unfinished attic or an exterior wall, smoke alarms and smoke detectors shall be mounted on an inside wall. (4) Smoke alarms or smoke detectors shall be installed a minimum of 20 feet horizontal distance from a permanently installed cooking appliance. Exceptions: Ionization smoke alarms with an alarm silencing switch or photoelectric smoke alarms shall be permitted to be installed 10 feet (3 m) or greater from a permanently installed cooking appliance. Photoelectric smoke alarms shall be permitted to be installed greater than 6 feet (1.8 m) from a permanently installed cook- ing appliance where the kitchen or cooking area and adjacent spaces have no clear interior partitions and the 10 ft distances would prohibit the placement of a smoke alarm or smoke detector required by other sections of the code. Smoke alarms listed for use in close proximity to a permanently installed cooking appliance. (5) Effective January 1, 2016, smoke alarms and smoke detectors used in household fire alarm systems installed between 6 ft (1.8 m) and 20 ft (6.1 m) along a horizontal flow path from a stationary or fixed cooking appliance shall be listed for resis- tance to common nuisance sources from cooking. (6) Installation near bathrooms. Smoke alarms shall be installed not less than a 3-foot (0.91 m) horizontal distance from the door or opening of a bathroom that contains a bathtub or shower unless this would prevent placement of a smoke alarm required by other sections of the code. (7) Smoke alarms and smoke detectors shall not be installed within a 36 in. (910 mm) horizontal path from the supply registers of a forced air heating or cooling system and shall be installed outside of the direct airflow from those registers. (8) Smoke alarms and smoke detectors shall not be installed within a 36 in. (910 mm) horizontal path from the tip of the blade of a ceiling-suspended (paddle) fan. (9) Where stairs lead to other occupied levels, a smoke alarm or smoke detector shall be located so that smoke rising in the stairway cannot be prevented from reaching the smoke alarm or smoke detector by an intervening door or obstruction. (10) For stairways leading up from a basement, smoke alarms or smoke detectors shall be located on the basement ceiling near the entry to the stairs. (11) For tray-shaped ceilings (coffered ceilings), smoke alarms and smoke detectors shall be installed on the highest portion of the ceiling or on the sloped portion of the ceiling within 12 in. (300 mm) vertically down from the highest point. (12) Smoke alarms and detectors installed in rooms with joists or beams shall comply with the requirements of 17.7.3.2.4 of NFPA 72. (13) Heat alarms and detectors installed in rooms with joists or beams shall comply with the requirements of 17.6.3 of NFPA 72. 211—16: Standard for Chimneys, Fireplaces, Vents and Solid Fuel Burning Appliances R1002.5

ically down from the highest point._ (12) Smoke alarms and detectors installed in rooms with joists or beams shall comply with the requirements of 17.7.3.2.4 of NFPA 72. (13) Heat alarms and detectors installed in rooms with joists or beams shall comply with the requirements of 17.6.3 of NFPA 72. 211—16: Standard for Chimneys, Fireplaces, Vents and Solid Fuel Burning Appliances R1002.5

259—18: Standard for Test Method for Potential Heat of Building Materials R316.5.7, R316.5.8

100735044

REFERENCED STANDARDS

NFPA—continued 275—17: Standard Method of Fire Tests for the Evaluation of Thermal Barriers R316.4

286—15: Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth R302.9.4, R316.6

720—15: Standard for the Installation of Carbon Monoxide (CO) Detectors and Warning Equipment R315.7.1, R315.7.2

PCA Portland Cement Association

5420 Old Orchard Road Skokie, IL 60077

100—12: Prescriptive Design of Exterior Concrete Walls for One- and Two-family Dwellings (Pub. No. EB241) R301.2.2.5, R301.2.2.3.4, R404.1.3, R404.1.3.2.1, R404.1.3.2.2, R404.1.3.4, R404.1.4.2, R608.1, R608.2, R608.5.1, R608.9.2, R608.9.3

SBCA Structural Building Components Association

6300 Enterprise Lane Madison, WI 53719

BCSI—2013 (Updated March 2015): Building Component Safety Information Guide to Good Practice for Handling, Installing, Restraining & Bracing of Metal Plate Connected Wood Trusses

R502.11.2, R802.10.3

CFS-BCSI—2008: Cold-formed Steel Building Component Safety Information (CFSBCSI) Guide to Good Practice for Handling, Installing & Bracing of Cold-formed Steel Trusses

R505.1.3, R804.3.6

FS100—12: Standard Requirements for Wind Pressure Resistance of Foam Plastic Insulating Sheathing Used in Exterior Wall Covering Assemblies

R316.8

SFM State of California Department of Forestry and Fire Protection

Office of the State Fire Marshal

P.O. Box 944246 Sacramento, CA 944246-2460

SFM 12-3: Releasing Systems for Security Bars in Dwellings

R310

SFM 12-7A-1: Exterior Wall Siding and Sheathing

R327.5.3, R327.6.3.1, R327.6.3.2.3

SFM 12-7A-2: Exterior Window

R327.5.3, R327.6.3.2.2

SFM 12-7A-3: Horizontal Protection Underside

R327.5.3, R327.6.2.3

SFM 12-7A-4: Decking

R327.5.3, R327.6.4.1.1

SFM 12-7A-4A: Decking Alternate Method A

R327.3.7, R327.9.3.4

SFM 12-7A-5: Ignition Resistant Building Material

R327.2, R327.3.7, R327.4.2, R327.6.3.2, R327.9.3.1

(The Office of the State Fire Marshal standards referred to above are found in the California Code of Regulations, Title 24, Part 12.)

TMS The Masonry Society 105 South Sunset Street, Suite Q Longmont, CO 80501

402—2016: Building Code Requirements for Masonry Structures R404.1.2, R606.1, R606.1.1, R606.12.1, R606.12.2.3.1, R606.12.3.1, R703.12

403—2017: Direct Design Handbook for Masonry Structures R606.1, R606.1.1, R606.12.1, R606.12.3.1

552 2019 CALIFORNIA RESIDENTIAL CODE

100735044

REFERENCED STANDARDS

TMS—continued 404—2016: Standard for the Design of Architectural Cast Stone R606.1

602—2016: Specification for Masonry Structures 606.2.10, R606.2.13, R703.12

TPI Truss Plate Institute 218 N. Lee Street, Suite 312 Alexandria, VA 22314

TPI 1—2014: National Design Standard for Metal-plate-connected Wood Truss Construction

R502.11.1, R802.10.2

UBC International Code Council, Inc. 500 New Jersey Avenue, NW 6th Floor Washington, DC 20001

UBC Standard 15-2: Test Standard for Determining the Fire Retardancy of Roof-covering Materials

R902

UBC Standard 15-3: Wood Shakes

R902

UBC Standard 15-4: Wood Shingles

R902

UL UL LLC 333 Pfingsten Road Northbrook, IL 60062

55A—04: Materials for Built-up Roof Coverings R905.9.2

103—2010: Factory-built Chimneys for Residential Type and Building Heating Appliances—with revisions through July 2012 R202, R1005.3

127—2011: Factory-built Fireplaces—with revisions through May 2015 R1001.11, R1004.1, R1004.4, R1004.5, R1005.4

217—06: Single- and Multiple-station Smoke Alarms—with revisions through October 2015 R314.1.1, R315.1.1

263—2011: Standards for Fire Test of Building Construction and Materials—with revisions through June 2015 Table 302.1(1), Table R302.1(2), R302.2, R302.2.1, R302.2.2, R302.4.1, R302.11.1, Table R312.1(1), R606.2.2

268—2009: Smoke Detectors for Fire Alarm Systems R314.7.1, R314.7.4, R315.7.4

325—02: Door, Drapery, Gate, Louver and Window Operations and Systems—with revisions through May 2015 R309.4

641—2010: Type L, Low-temperature Venting Systems—with revisions through June 2013 R202, R1003.11.5

723—08: Standard for Test for Surface Burning Characteristics of Building Materials—with revisions through August 2013 R202, R302.9.3, R302.9.4, R302.10.1, R302.10.2, R316.3, R316.5.9, R316.5.11, R507.2.2.2, R703.14.3, R802.1.5

790—04: Standard Test Methods for Fire Tests of Roof Coverings—with revisions through July 2014 R302.2.4, R902.1

959—2010: Medium Heat Appliance Factory-built Chimneys—with revisions through June 2014 R1005.6

1040—96: Fire Test of Insulated Wall Construction—with revisions through October 2012 R316.6

1256—02: Fire Test of Roof Deck Construction—with revisions through July 2013 R906.1

1479—03: Fire Tests of Through-Penetration Firestops—with revisions through June 2015 R302.4.1.2

100735044

REFERENCED STANDARDS

UL—continued

1482—2011: Solid-fuel-type Room Heaters—with revisions through August 2015

R1002.2, R1002.5

1618—09: Wall Protectors, Floor Protectors, and Hearth Extensions—with revisions through October 2015

R1004.2

1703—02: Flat-plate Photovoltaic Modules and Panels—with revisions through October 2015

R324.3.1, R902.4, R905.16.4, R907.17.5

1715—97: Fire Test of Interior Finish Material—with revisions through January 2013

R316.6

1741—2010: Inverters, Converters, Controllers and Interconnection System Equipment with Distributed Energy Resources—with revisions through January 2015

R324.3.1, R327.4

1777—07: Chimney Liners—with revisions through October 2015

R1003.11.1, R1003.18

1897—12: Uplift Tests for Roof Covering Systems—with revisions through September 2015

R905.17.7

2034—08: Standard for Single- and Multiple-station Carbon Monoxide Alarms—with revisions through March 2015

R314.1.1, R315.1.1

2075—2013: Standard for Gas and Vapor Detectors and Sensors

R314.7.4, R315.7.1, R315.7.4

2703—14: Mounting Systems, Mounting Devices, Clamping/Retention Devices and Ground Lugs for Use with Flat-Plate Photovoltaic Modules and Panels

R902.4

9540—14: Outline of Investigation for Energy Storage Systems and Equipment

R327.2, R327.4

ULC ULC

13775 Commerce Parkway

Richmond, BC V6V 2V4

CAN/ULC S 102.2—2010: Standard Methods for Test for Surface Burning Characteristics of Building Materials and Assemblies

R302.10.1, R302.10.2

WDMA Window and Door Manufacturers Association

2025 M Street NW, Suite 800

Washington, DC 20036-3309

AAMA/WDMA/CSA 101/I.S2/A440—17: North American Fenestration Standard/Specifications for Windows, Doors and Skylights

R308.6.9, R609.3

I.S. 11—13: Industry Standard Analytical Method for Design Pressure (DP) Ratings of Fenestration Products

R308.6.9.1, R609.3.1

WMA World Millwork Alliance (formerly Association of Millwork Distributors Standards AMD)

10047 Robert Trent Parkway

New Port Richey, FL 34655-4649

ANSI WMA 100—2016: Standard Method of Determining Structural Performance Ratings of Side Hinged Exterior Door Systems and Procedures for Component Substitution

R609.3

554 2019 CALIFORNIA RESIDENTIAL CODE

100735044

APPENDIX A

RESERVED

100735044

556 2019 CALIFORNIA RESIDENTIAL CODE Copyright © 2019 ICC. ALL RIGHTS RESERVED. Accessed by Kevin Day (kevin.day@dgs.ca.gov), (California Building Standards Commission) Order Number #100735044 on Jul 24, 2019 03:54 PM (PDT) pursuant to License Agreement with ICC. No further reproduction or distribution authorized. Single user only, copying and networking prohibited. ANY UNAUTHORIZED REPRODUCTION OR DISTRIBUTION IS A VIOLATION OF THE FEDERAL COPYRIGHT ACT AND THE LICENSE AGREEMENT, AND SUBJECT TO CIVIL AND CRIMINAL PENALTIES THEREUNDER.

100735044

APPENDIX B

RESERVED

100735044

558 2019 CALIFORNIA RESIDENTIAL CODE Copyright © 2019 ICC. ALL RIGHTS RESERVED. Accessed by Kevin Day (kevin.day@dgs.ca.gov), (California Building Standards Commission) Order Number #100735044 on Jul 24, 2019 03:54 PM (PDT) pursuant to License Agreement with ICC. No further reproduction or distribution authorized. Single user only, copying and networking prohibited. ANY UNAUTHORIZED REPRODUCTION OR DISTRIBUTION IS A VIOLATION OF THE FEDERAL COPYRIGHT ACT AND THE LICENSE AGREEMENT, AND SUBJECT TO CIVIL AND CRIMINAL PENALTIES THEREUNDER.

100735044

APPENDIX C

RESERVED

100735044

560 2019 CALIFORNIA RESIDENTIAL CODE Copyright © 2019 ICC. ALL RIGHTS RESERVED. Accessed by Kevin Day (kevin.day@dgs.ca.gov), (California Building Standards Commission) Order Number #100735044 on Jul 24, 2019 03:54 PM (PDT) pursuant to License Agreement with ICC. No further reproduction or distribution authorized. Single user only, copying and networking prohibited. ANY UNAUTHORIZED REPRODUCTION OR DISTRIBUTION IS A VIOLATION OF THE FEDERAL COPYRIGHT ACT AND THE LICENSE AGREEMENT, AND SUBJECT TO CIVIL AND CRIMINAL PENALTIES THEREUNDER.

100735044

APPENDIX D

RESERVED

100735044

562 2019 CALIFORNIA RESIDENTIAL CODE Copyright © 2019 ICC. ALL RIGHTS RESERVED. Accessed by Kevin Day (kevin.day@dgs.ca.gov), (California Building Standards Commission) Order Number #100735044 on Jul 24, 2019 03:54 PM (PDT) pursuant to License Agreement with ICC. No further reproduction or distribution authorized. Single user only, copying and networking prohibited. ANY UNAUTHORIZED REPRODUCTION OR DISTRIBUTION IS A VIOLATION OF THE FEDERAL COPYRIGHT ACT AND THE LICENSE AGREEMENT, AND SUBJECT TO CIVIL AND CRIMINAL PENALTIES THEREUNDER.

100735044

APPENDIX E

RESERVED

100735044

564 2019 CALIFORNIA RESIDENTIAL CODE Copyright © 2019 ICC. ALL RIGHTS RESERVED. Accessed by Kevin Day (kevin.day@dgs.ca.gov), (California Building Standards Commission) Order Number #100735044 on Jul 24, 2019 03:54 PM (PDT) pursuant to License Agreement with ICC. No further reproduction or distribution authorized. Single user only, copying and networking prohibited. ANY UNAUTHORIZED REPRODUCTION OR DISTRIBUTION IS A VIOLATION OF THE FEDERAL COPYRIGHT ACT AND THE LICENSE AGREEMENT, AND SUBJECT TO CIVIL AND CRIMINAL PENALTIES THEREUNDER.

100735044

CALIFORNIA RESIDENTIAL CODE – MATRIX ADOPTION TABLE