§ 8106-8

(a)

Prior to the construction of any of the following, a Zoning Clearance is required:

(1)

Fences that are over seven (7) feet in height measured from grade to the top of fence.

(2)

Any fence that requires electricity for light fixtures and/or to power an entry gate.

(3)

Any retaining wall that is over three (3) feet in height measured from grade on the lower side, to the top of the wall, and/or supporting a surcharge.

(b)

A separate tree permit may be required for the construction of a fence or gate that alters any protected tree pursuant to Section 8107-25 of this Chapter.

(c)

All fencing within the HCWC Overlay Zone must be installed in compliance with the standards of Section 81094.8 of this Chapter.

(d)

All fencing within the CWPA Overlay Zone must be installed in compliance with the standards of Section 81094.9 of this Chapter.

(Ord. No. 4606, § 3, 11-1-2022)

No barbed wire, razor-edge wire, electric wire or similar type of fencing (see photographic examples below) is permitted in urban residential zones or commercial zones (see Article 4), or on properties in industrial zones which abut or are across the street from urban residential zoned properties, if such fencing would be visible from the urban residential zoned property or properties.

==> picture [361 x 85] intentionally omitted <==

Examples of Prohibited Fencing

(Ord. No. 4606, § 3, 11-1-2022)

The height of fences and retaining walls shall be measured in accordance with the following subsections and as illustrated in Figure 1 below.

(a)

For purposes of this section, "grade" shall be the lowest level parallel to and five (5) feet from the fence or retaining wall.

(b)

Height of a fence or retaining wall shall be measured from grade to the highest point of the fence or retaining wall.

(c)

Where there is a difference in grade levels on the two (2) sides of a fence, the height of such fence shall be measured from the higher grade, provided that the distance from the lower grade to the top of the fence shall not exceed ten (10) feet, and further provided that in a required setback adjacent to a street, the fence height shall be measured from adjacent grade of the street side of the fence. See Section 8106-8.1.7 below for additional regulations pertaining to structural retaining walls.

Figure 1

==> picture [326 x 315] intentionally omitted <==

• (Am. Ord. 3730—5-7-1985; Ord. 4216—10-24-2000; Ord. No. 4606, § 3, 11-1-2022)

8106-8.1.5 - Fences required by law.

The provisions of Section 8106-8.1 et seq. shall not apply to a fence required by any law or regulation of a federal, state or local governmental entity.

(Ord. 3810—5-5-1987; Ord. 4092—6-27-1995; Ord. No. 4606, § 3, 11-1-2022)

For purposes of this Section 8106-8.1 et seq., protected trees (listed in Table 1 of Section 8107-25) do not constitute a fence. Any alterations to a protected tree shall be in compliance with the tree protection regulations of Section 8107-25 et seq. of this Chapter.

(Ord. 3993—2-25-1992; Ord. No. 4606, § 3, 11-1-2022)

8106-8.1.7 - Retaining walls.

Structural retaining walls to stabilize a bank or protect a cut below grade do not have a height limit, unless the walls are located within a ten-foot by ten-foot right triangle on each side of a driveway adjacent to a street, in

which case the retaining wall cannot exceed three (3) feet tall as measured in accordance with Section 81068.1.4 of this Chapter. Notwithstanding the foregoing, structural retaining walls are not subject to the setback regulations of Sections 8106-1.1 and 8106-1.2 of this Chapter. Where a fence is installed on top of a retaining wall, the total combined height of the retaining wall and the fence shall not exceed ten (10) feet tall as measured from the side of the fence with the lower grade to the top of the fence. Fences installed on top of retaining walls shall meet the setback regulations of Sections 8106-1.1 and 8106-1.2 and the fence regulations of Section 8106-8.1 of this Article. See photographic examples and Figure 2 below.

Figure 2

==> picture [350 x 298] intentionally omitted <==

(Ord. No. 4606, § 3, 11-1-2022)

8106-8.2.1 - Applicability.

(a)

Section 8106-8.2 applies to all discretionary development projects that include or are required to include landscaping in the following zones:

(1)

CO Zone

(2)

C1 Zone

(3)

CPD Zone

(4)

M Zones

(5)

RPD Zone

(6)

RHD Zone

Sections 8109-0.6, 8109-1.2 and 8109-1.3 contain additional landscape requirements by zone.

(b)

Any ministerial or discretionary development project that meets one (1) or more of the criteria listed below is subject to the State Model Water Efficient Landscape Ordinance (MWELO):

(1)

New construction projects with an aggregate landscape area equal to or greater than five hundred (500) square feet requiring a building permit, building plan check, or landscape plan.

(2)

Retrofitted landscape projects with an aggregate landscape area equal to or greater than two thousand five hundred (2,500) square feet requiring a building permit, building plan check, or landscape plan.

(3)

Existing landscapes are limited to complying with Sections 493, 493.1 and 493.2 of the MWELO.

(4)

Cemeteries: New and retrofitted cemetery development is subject to Sections 492.4, 492.22 and 492.12 of the MWELO and existing cemetery development is subject to Sections 493, 493.1 and 493.2 of the MWELO.

(5)

Any project with an aggregate landscape area of two thousand five hundred (2,500) square feet or less is required to comply either with the performance requirements of the MWELO or conform to the prescriptive compliance provisions contained in Appendix D of the MWELO.

(6)

Graywater/Rainwater Capture: Any lot that with less than two thousand five hundred (2,500) square feet of landscape area that meets the lot's landscape water requirement using entirely graywater or stored rainwater captured on site is subject only to the prescriptive compliance provisions contained in Appendix D of the MWELO.

(7)

Notwithstanding the foregoing, the MWELO does not apply to:

a.

Registered local, state or federal historical sites;

b.

Ecological restoration projects that do not require a permanent irrigation system;

c.

Mined-land reclamation projects that do not require a permanent irrigation system; and

d.

Existing plant collections, as part of botanical gardens and arboretums open to the public.

(c)

Discretionary development projects subject to the MWELO pursuant to subsection (b) above shall also be subject to Section 8106-8.2.

(d)

All discretionary development projects subject to landscaping requirements that require permanent irrigation, including those not otherwise subject to the MWELO, shall be subject to MWELO, Appendix D, subsections (b) (5) and (6), as may be amended.

(e)

All development projects subject to landscaping requirements for parking areas pursuant to Section 8108-5.14 shall comply with Sections 8106-8.2.2, 8106-8.2.3, and 8106-8.2.8. Section 8106-8.2.7 shall apply to any parking areas containing manufactured slopes.

(f)

Where conformance to the standards and requirements of this Section 8106-8.2 would create practical difficulties or undue hardship for the project applicant, the Planning Director or designee may grant modifications to the requirements of this Section, provided the proposed modifications are the minimum necessary to alleviate the practical difficulties or undue hardship. This provision does not apply to standards and requirements imposed by the MWELO.

(g)

Where the landscaping standards conflict with one another, the more restrictive landscaping standard shall apply. The applied standard shall meet or exceed minimum standards required by the MWELO.

(Ord. No. 4577 § 2, 3-9-2021)

(a)

Applications for development projects with proposed landscaping not subject to the MWELO shall submit a landscape plan that meets the following standards:

(1)

The landscape plan shall clearly illustrate compliance with all landscape requirements set forth or referenced in the NCZO applicable to the project.

(2)

All landscape plans shall be drawn to scale and be consistent with the project's site plan.

(3)

Landscape plans containing greater than five hundred (500) square feet of landscape area shall be designed by and bear the signature of a licensed landscape architect.

(4)

When an applicant chooses to retain native vegetation to reduce the amount of required landscaping in accordance with Section 8106-8.2.4 or to incorporate insect nesting habitat into the landscape area, these areas shall be shown within the landscape plan.

(b)

Development projects subject to the requirements of the MWELO (see Section 8106-8.2.1(b)) shall submit a Landscape Documentation Package that includes a water efficient landscape worksheet, soil management report, landscape design plan, irrigation design plan and grading design plan pursuant to, and as described in, Sections 492.3 through 492.8 of the MWELO, as may be amended.

(Ord. No. 4577 § 2, 3-9-2021)

(a)

No land use may be inaugurated, or structure occupied, until a final inspection has been completed verifying that the landscape area has been installed as required by the approved entitlement.

(b)

All existing invasive and watch list species as inventoried by the California Invasive Plant Council shall be properly disposed of and removed from the landscape area before the installation of the approved landscaping.

(c)

Landscaping installed within a Hazardous Fire Area, Wildland Urban Interface Zone, or Fire Hazard Severity Zone shall be subject to all applicable Ventura County Fire Protection District landscaping requirements.

(d)

Landscape Design Elements.

(1)

Vines, shrubs, and other trees shall be used to visually soften and deter graffiti on walls and fences. Vines shall not be used where they will cause structural damage to walls or obstruct traffic safety sight area when adjacent to a roadway or driveway.

(2)

Plants shall be grouped according to hydrozones and other environmental conditions (soil, slope, sun exposure) that are appropriate for their survival.

(3)

Trees shall be planted in all parkway areas between curbs and sidewalks or in sidewalk tree wells as follows:

(4)

Sizes for mature trees as used in this Section 8106-8.2 are defined as follows: "small trees" will reach thirty (30) feet or less in height; "medium trees" will reach between thirty (30) to seventy (70) feet in height; and "large trees" will reach seventy (70) feet or more in height.

(5)

Trees should not be planted under existing tree canopies unless required for habitat restoration purposes. New trees shall be installed using the following setback distances from an existing tree at mature tree size: small trees require a 20-foot setback; medium trees require a 30-foot setback; and, large trees require a 40-foot setback.

(6)

Trees and shrubs shall be planted so that at maturity they do not interfere with service lines, sewer lines or onsite wastewater treatment system areas, traffic safety sight areas, public works facilities and rights-of-way, or safety lighting.

(7)

Trees that typically grow taller than twenty (20) feet in height at maturity are not permitted under utility wires and shall not be planted under utility pole guy wires anchored to the ground.

(8)

Landscape areas shall include permanent irrigation systems and may contain water features and pedestrian walkways. Notwithstanding the foregoing, permanent irrigation systems shall not be required for native vegetation retained through the native vegetation credit program pursuant to Section 8106-8.2.4, provided that the overall hydrologic regime that supports the vegetation remains unaltered or permanent irrigation is unnecessary for the type of vegetation community retained. Temporary irrigation systems may still be required to establish native plantings.

(9)

Landscape projects not otherwise subject to the MWELO, shall design and install any permanent irrigation system pursuant to MWELO, Appendix D(b)(5) and (6).

(e)

Plant and Landscaping Materials.

(1)

Mulch should support plantings within the landscape area but should not substitute for plant material. Waterefficient landscape designs that contain large areas of mulch shall be reviewed on a case-by-case basis to ensure adequate plant material is present for the purpose of reducing heat island effects, erosion control, or other factors. To the maximum extent feasible, mulch shall be free of weed seeds and deleterious materials such as plastic, trash, and toxic leachates.

(2)

The use of native host plants for butterfly and moth caterpillars, and native plants and landscape features which create habitat for other beneficial invertebrates and vertebrates (including birds) is strongly encouraged. The Ventura County Pollinator-Friendly Guidelines and other organizations provide lists of native host plants for pollinators and recommendations for other pollinator-friendly, beneficial invertebrate-friendly, and vertebratefriendly landscape design practices.

(3)

Native vegetation must comprise at least fifty (50) percent of the plant types in new or retrofitted landscape areas. Where feasible, existing native vegetation should be retained within the landscape area.

(4)

To provide year-round food resources for pollinator diversity, the landscape area shall contain at least eight (8) different plant species with bloom times that are sequential or overlap throughout the year (e.g., two (2) to three (3) plant species for each spring, summer/fall, and winter). To the extent feasible, selected plant species should differ in color, structure, size, and scent.

(5)

Native vegetation retained pursuant to Section 8106-8.2.4 may be included in native and plant diversity calculations in Section 8106-8.2.3(e).

(6)

When the required size, number and types of plant specimens cannot be met due to factors such as a small landscape area, unusual site conditions or Area Plan design standards, the Planning Director or designee may waive or modify such requirements. However, a written explanation by the landscape architect shall be required to describe how the proposed size, number and types of proposed plants meet the standards above to the maximum extent feasible.

(7)

The following plant types are prohibited from use in landscape plantings:

a.

Tropical milkweed (Asclepias curassavica), due to its transmission of a debilitating parasite (Ophryocystis elektroscirrha) to Western monarch butterflies; and

b.

Invasive and watch list species as inventoried by the California Invasive Plant Council.

(8)

The largest mature tree size shall be planted wherever feasible with respect to the current uses of the site, pedestrian circulation, vehicle circulation, safety, and standard setbacks. To the maximum extent feasible, native trees should be selected.

(9)

Irrigation equipment or incompatible landscaping material (e.g., weed fabric) shall not be sited or installed within any oak tree (Quercus spp.) dripline unless approved by the Planning Division. All permanent irrigation systems shall be kept a minimum of ten (10) feet from the drip line of any existing oak species, except when recommended by a certified arborist under extreme drought conditions. In such circumstances, a targeted irrigation schedule and maintenance plan for these areas shall be included with the landscape plan (see Section 8106-8.2.8).

(10)

Any landscaping within the dripline of oak trees shall consist of plant species compatible with the water and soil requirements of the oak. Plants installed within the dripline should serve as accents rather than as a groundcover. Where possible, natural leaf mulch should not be removed. To protect the long-term health of established oak trees, landscaping or earth disturbance shall not occur within ten (10) feet of the tree trunk.

(Ord. No. 4577 § 2, 3-9-2021)

8106-8.2.4 - Voluntary native plant preservation incentive.

(a)

Purpose. The purpose of this voluntary incentive is to preserve and integrate existing mature, healthy, unprotected native vegetation into required landscape areas within the project site. This approach will promote pollinator-friendly landscapes, reduce water use, reduce landscape installation costs for the applicant, and

reduce long-term landscape maintenance costs for the landowner. Native vegetation retained pursuant to this Section 8106-8.2.4 shall help to meet the purpose of the landscaping requirements (e.g., screening).

(b)

Applicability. This native vegetation preservation incentive is only available to discretionary projects that require an Initial Study Biological Assessment (ISBA). This incentive is not applicable to parking lot landscaping (Section 8108-5.14) or stormwater landscaping requirements required by the Ventura County Watershed Protection District.

(c)

Incentive Calculations.

(1)

Landscape credit for preserved native vegetation community alliances and native plant specimen(s) shall be granted at a 1:1 ratio (one (1) square foot of retained native vegetation, including root zone, will count for one (1) square foot of landscape area required in Sections 8109-0.6, 8109-1.2 or in landscape screening requirements).

(2)

The above-stated 1:1 ratio may be increased to 1:2 (one (1) square foot of retained native vegetation, including root zone, will count for two (2) square feet of landscape area required in Sections 8109-0.6, 8109-1.2 or in landscape screening requirements) when the preservation area is located:

a.

Within two hundred (200) feet of a verified mapped hydrological feature (USFWS National Wetlands Inventory or USGS National Hydrographic Data Sets) or an identified sensitive biological resource area;

b.

Within the Habitat Connectivity and Wildlife Corridor Overlay Zone; or

c.

Immediately adjacent to a legally protected native vegetation community that is both greater than two thousand (2,000) square feet and meets the requirements of Section 8106-8.2.4(e)(3) and (4) below). To receive preservation credit under these criteria, the edge of the vegetation canopies between preserved area and the adjacent native vegetation community must be within thirty (30) feet of one another with no obstructions or barriers for wildlife movement.

(3)

If the preservation area is greater than thirty (30) percent of the landscape area using this preservation credit, the Planning Director or designee may require additional landscaping to meet screening or other visual quality requirements as set forth in the NCZO.

(d)

Documentation. Applicants seeking a preservation credit shall provide a Planning Division-approved Initial Study Biological Assessment (ISBA) for the site that includes a map and table showing the location, native plant specimen(s) species or native vegetation community alliance (if a plant community is retained), size (area and height), easements/right(s)-of-way/utility lines, fuel modification zones, invasive or watch list species, and the health of each native plant specimen(s) or native vegetation community alliance retained for credit. Photos of each unprotected native plant specimen(s) proposed for retention must also be provided. County staff may request a site visit to determine the suitability of the area for preservation credit.

(e)

Native Plant Characteristics. The native vegetation used for preservation credit must meet the following standards when surveyed for the ISBA and before the final Certificate of Occupancy is issued:

(1)

The native vegetation is not required to be preserved by local, state, or federal law.

(2)

The root system, and surrounding microclimate area that is outside the native plant dripline, shall be retained intact and unaltered (includes natural or man-made means), unless such alterations are compatible and support the long-term health of the native vegetation (e.g., companion planting, mulching, etc.) depicted in the approved final landscape plan.

(3)

The native vegetation community alliance or native plant specimen(s) and their buffer area(s) are not dominated by invasive or watch list species, as inventoried by the California Invasive Plant Council, or otherwise deemed not ecologically suitable as recommended by a qualified biologist, and are approved by the Planning Director or designee.

(4)

There are no areas proposed for preservation where the soil was previously compacted, graded, or cultivated where it is no longer suitable for the original native vegetation community.

(f)

Standards for Landscaping with Existing Native Plants.

(1)

Any existing invasive or watch list species must be removed and properly disposed of as part of the site preparation process prior to the issuance of the Zoning Clearance for Construction or Use Inauguration (as applicable to the project);

(2)

The preservation area (existing native vegetation including root zone(s)) must be clearly marked and identified for protection on all project site plans, grading plans, outdoor lighting plans, and conceptual and final

landscape/restoration plans. The preservation area must be physically identified on-site prior to any site disturbance.

(3)

The native vegetation is not damaged, dead, dying, diseased, or infested with harmful insects. Any damaged vegetation within the preservation areas shall be replaced with vegetation equivalent to the vegetation that was destroyed. Site alterations that may cause the decline or death of the native vegetation in the preservation area (e.g., alterations to drainage or runoff, damage to plant root systems, exposure to sun and wind due to loss of vegetation cover in buffer area) shall be corrected to ensure the long-term health of the preserved native vegetation.

(4)

The preservation area shall be maintained or enhanced pursuant to the landscape maintenance standards of Section 8106-8.2.8.

(Ord. No. 4577 § 2, 3-9-2021)

(a)

Plant Material Spacing for Visual Screening.

(1)

Trees shall be planted at a minimum rate of one (1) for each thirty (30) linear feet of the landscape area. Shrubs shall be installed as needed to adequately screen the development, but no less than one (1) for every five (5) linear feet of landscape area.

(2)

Plants may be used as the main screening element only if a minimum of fifty (50) percent of the plants are of 15-gallon container size when planted, the remaining plants are of 5-gallon container size, and the plants will form a dense hedge that adequately screens the development year-round.

(b)

Visual Screening Using Berms, Walls, Fencing and Art.

(1)

Landscaping is the preferred method to soften the screening of storage areas, trash enclosures, parking areas and public utilities. Visual screens composed of a berm, fence, or solid wall shall include plant material that softens the look and breaks up the expanse of the screen. When the berm, fence, or wall is installed along the street side of a property line, the fence or wall is to be placed along the interior side of the landscaped area relative to the street.

(2)

Where earth berms are used, the berm slope shall be a maximum of one (1) foot of rise for every three (3) feet of linear distance (3:1 horizontal to vertical).

(3)

Public art may be incorporated into screening materials that are viewable by the public, in lieu of two (2) required trees. Such art shall meet the provisions of Section 8108-5.14.2(b)(2)(ii).

(Ord. No. 4577 § 2, 3-9-2021)

8106-8.2.6 - General stormwater landscape design.

(a)

Stormwater management landscaping shall meet the following standards:

(1)

The minimum coverage of plant species meets water quality improvement plans.

(2)

Plant types shall be selected to withstand periodic inundation of water, survive seasonal drought, and be capable of pollutant uptake. Irrigation shall be used to allow for the establishment of the selected plants and cuttings.

(3)

When mulch is used within stormwater management landscaping, it shall be non-floatable and well-aged to prevent clogging of storm drain infrastructure.

(4)

Required trees shall be planted above the flow line of basins or channels;

(5)

The landscaping does not reduce or negatively affect the number, type, size, location, or health of required and protected trees.

(Ord. No. 4577 § 2, 3-9-2021)

Manufactured (i.e., human-made) slopes shall be planted pursuant to the following standards:

(a)

Slopes steeper than 3:1 shall include erosion control blankets, soil stabilizers or other means approved by the Public Works Agency to prevent erosion.

(b)

Groundcover. Manufactured slopes shall be planted with groundcover to minimize erosion and blend with the adjacent natural slopes. The type of groundcover selected shall be compatible with soils and climatic conditions, adjacent native vegetation or landscaping, irrigation requirements, and fire-retardant requirements.

(c)

Trees and Shrubs. Manufactured slopes shall have a mixture of trees and shrubs incorporated with groundcover to assure soil stabilization, blend with adjacent native vegetation or landscaping, and promote varying height and mass of landscaping. Shrubs are not required for sloped areas less than three (3) feet high created by the deposition of material (e.g., artificial berm). Trees are not required for sloped areas less than five (5) feet high created through the excavation of material (e.g., cut bank).

(d)

Slope Irrigation. Soil type and percolation rate shall be considered when designing slope irrigation. Properly designed and installed sprinklers or drip irrigation systems may be necessary to promote slope stability.

(Ord. No. 4577 § 2, 3-9-2021)

8106-8.2.8 - Landscape maintenance.

(a)

Landscaping shall be maintained by the permittee according to the approved landscape plan and any permit conditions for the life of the permitted land use. Maintenance activities shall include the following:

(1)

Routine inspections to guard against runoff and erosion and to detect plant or irrigation system failure. Failure to maintain required landscaping or irrigation systems shall constitute a violation of the permit pursuant to Article 14.

(2)

Landscape areas with installed irrigation shall maintain these areas pursuant to MWELO, Section 492.11, as may be amended, regardless of whether the MWELO otherwise applies.

(3)

Shrubs and groundcovers shall be pruned to keep plants within planting beds. Pruning for all plants shall be conducted in accordance with the American National Standard for Tree Care Operations — Tree, Shrub, and Other Woody Plant Maintenance-Standard Practices ANSI A300 (Part 1) 2001 Pruning, ISA ANSI A300 1995, as may be amended.

(4)

Weeds and litter shall be removed from the landscape area.

(5)

Dead, dying, diseased or severely damaged plant material shall be replaced. Tree replacement shall be subject to Section 8107-25.

(6)

Tree supports shall be inspected frequently and removed when the tree can withstand high winds unsupported.

(7)

Mulch shall be monitored and replenished as needed.

(8)

Plants shall be fertilized and watered at such intervals as are necessary to promote optimum growth.

(b)

Areas with native vegetation that are retained for preservation credit pursuant to Section 8108-8.2.4 shall be maintained according to an approved Invasive Species Management Plan that is submitted with the landscape plan.

(c)

Non-toxic methods of pest control within the landscape area are strongly encouraged.

(Ord. No. 4577 § 2, 3-9-2021)

8106-8.2.9 - Permit modifications for landscape plans.

Proposed modifications to an existing, approved landscape plan shall be processed in accordance with Article 11, except that minor adjustments that comply with the following requirements shall be approved through the issuance of a Zoning Clearance:

(a)

The proposed adjustments are not subject to the MWELO.

(b)

Replacement plant materials shall substantially conform with the original purpose and intent of the landscape regulations and must be recommended by a licensed landscape architect, landscape designer, or qualified biologist.

(c)

Replacement plant materials shall conform to the water, soil, slope, and sun exposure requirements of accompanying plantings.

(d)

Replacement plant materials shall not: (1) be an invasive or watch list species identified by the California Invasive Plant Council; or (2) increase the overall landscape water usage.

(e)

Changes to impervious surface area shall not cause the total impervious surface area on the lot to exceed more than five thousand (5,000) square feet.

(f)

The hydraulic line and grade within site drainage patterns shall not be altered.

(g)

A minor adjustment shall not:

(1)

Reduce or negatively affect the number, size, or health of required trees in the approved landscape plan;

(2)

Reduce or negatively affect the number, type, size, location, or health of existing protected trees; or

(3)

Impair compliance with landscape screening or storm water management requirements.

(Ord. No. 4577 § 2, 3-9-2021)

An accessory structure will be considered to be attached to the principal structure if:

a.

The distance between the principal structure and the accessory structure is no greater than fifteen (15) feet and the roof connecting the two (2) structures complies with all of the following:

(1)

It is essentially a continuation of the roof of the principal structure;

(2)

It resembles the roof of the nearest enclosed, habitable area of the principal structure in terms of pitch, materials, architectural design, etc.; and

(3)

It is imperforate; or

b.

The space between such structures is completely enclosed by walls attached to each structure and constitutes "internal access" and the ratio of this access-way width to length is no greater than 1:3.

(Am. Ord. 3810—5/5/87; Ord. No. 4618, § 3, 7-25-2023)

Where there are no traffic controls (i.e., stop signs or traffic signals) on either street at an intersection, a sight triangle must be provided on each corner adjacent to the intersection. No structures or landscaping over three (3) feet tall that could block the view of approaching traffic on either street shall be located or constructed within any required sight triangle.

(Add Ord. 3730—5/7/85; Am. Ord. 3810—5/5/87; Am. Ord. 4092—6/27/95; Ord. No. 4639, § 5, 12-17-2024)

Adequate sight distance shall be provided at intersections. In cases where the minimum setback requirements of Sec. 8106-1 do not provide such sight distance, particularly where streets intersect at less than ninety (90) degrees and traffic is controlled (e.g., by stop signs) on only one of the streets (the 'minor street'), setbacks for discretionary projects must be adjusted to provide adequate sight distance in accordance with the following table. The sight distance shall be measured from a point in the center of the minor street eight feet behind the designated stopping point for vehicles on such street, or behind a continuation of the intersecting curb line, to the center of the nearest (curbside) driving lane on the intersecting ('major') street. No structures or landscaping over three feet in height which could block the view of approaching traffic on the major street shall be constructed or located on the street side of the line connecting the two points. Curb cuts on discretionary projects should be considered minor streets for purposes of this section.

Speed Limit on Major Street (mph) Sight Distance Required (ft.)

(Add Ord. 3810—5/5/87)

8106-8.6 - Light fixtures.

The following regulations apply to light fixtures:

a.

A Zoning Clearance is required for freestanding light fixtures over two (2) feet up to twenty (20) feet tall on property with a zoning designation of open space, agricultural, or residential. Such light fixtures may be added to an existing developed lot in a commercial or industrial zone with a Zoning Clearance if the Planning Director or designee determines that the light fixtures are consistent with the existing approved entitlement for the

property and otherwise meets all other standards of this Chapter; otherwise, a modification to the existing approved entitlement shall be required.

b.

A freestanding light fixture over twenty (20) feet up to thirty-five (35) feet tall requires a Planning Directorapproved Planned Development Permit. In commercial and industrial zones, the maximum height of freestanding light fixtures shall be specified in a discretionary permit that approved the new development.

c.

Freestanding light fixtures shall not be placed in any side setbacks.

d.

Lights in excess of one hundred fifty (150) watts (for incandescent light bulbs) or two thousand two hundred fifty (2250) lumens shall be shielded, directed downward, and installed and maintained in such a manner to avoid light trespass beyond the lot line.

See Section 8109-4 of this Chapter for additional lighting regulations in overlay zones.

(Add Ord. 3810—5/5/87; Am. Ord. 4123—9/17/96; Ord. No. 4618, § 3, 7-25-2023; Ord. No. 4639, § 5, 12-172024)

8106-8.7 - Recycling and refuse storage areas.

All commercial, industrial, institutional, or residential buildings having five (5) or more living units, shall provide recycling and refuse storage areas in accordance with the County of Ventura's most recently adopted "Space Allocation for Recycling and Refuse Collection Design Criteria and Specifications Guidelines" in effect at the time of the development approval.

(Add Ord. 4054—2/1/94; Am. Ord. 4092—6/27/95; Ord. No. 4618, § 3, 7-25-2023)

Article 7. - Standards for Specific Uses