Atwater · Zoning · C-C
Atwater C-C zoning: height, setbacks and lot size
In Atwater's C-C zone, generally buildings can be up to 35 ft tall, the front setback is None required and the minimum lot size is 7,500 sq ft, with the conditions listed below (Atwater code, read October 2026).
Key points
- Maximum building height: 35 ft (may be exceeded if the further conditions the code lists after this limit are met)
- Minimum front setback: None required (None required, except as specified in Section 17.34.060)
- Minimum side setback: None required (None required, except as specified in Section 17.34.060)
- Minimum rear setback: None required (None required, except as specified in Section 17.34.060)
- Minimum lot size: 7,500 sq ft (new lots)
C-C (Central Commercial District) is a zoning district in Atwater. Every value below was read from the Atwater Municipal Code and links to its section (read October 2026). State laws such as the ADU and SB 9 rules can allow more on a residential lot. General information, not legal advice — read the code text and check with the city before you build.
Development standards in C-C
The general rule for a typical lot in this zone. Zoning tables often attach notes, such as rules for corner lots, lots next to a residential zone, or new subdivisions only. Open “code text” under a value to see the table cell or sentence it was read from.
| Maximum building height | 35 ft Applies: may be exceeded if the further conditions the code lists after this limit are met § 17.36.070 · code textNo building constructed in this zone shall exceed a height of 35 feet unless the following has occurred: |
|---|---|
| Minimum front setback | None required Applies: None required, except as specified in Section 17.34.060 § 17.36.070 · code textSetbacks: none, except as specified in Section 17.34.060. |
| Minimum side setback | None required Applies: None required, except as specified in Section 17.34.060 § 17.36.070 · code textSetbacks: none, except as specified in Section 17.34.060. |
| Minimum rear setback | None required Applies: None required, except as specified in Section 17.34.060 § 17.36.070 · code textSetbacks: none, except as specified in Section 17.34.060. |
| Minimum lot size | 7,500 sq ft Applies: new lots § 17.36.070 · code textNo new lots shall be created smaller than 7,500 square feet, and all new development shall comply with the following minimum requirements: |
Not on this page
We did not find a general stories, lot coverage, FAR, density limit for C-C in the zoning tables we read. The code may still set one elsewhere — check the Atwater Municipal Code.
Other Atwater zoning districts
Who this affects
Frequently asked questions
What is the maximum building height in Atwater's C-C zone?
35 ft (may be exceeded if the further conditions the code lists after this limit are met) — Atwater Municipal Code § 17.36.070.
What is the minimum front setback in Atwater's C-C zone?
None required (none required, except as specified in Section 17.34.060) — Atwater Municipal Code § 17.36.070.
What is the minimum side setback in Atwater's C-C zone?
None required (none required, except as specified in Section 17.34.060) — Atwater Municipal Code § 17.36.070.
What is the minimum rear setback in Atwater's C-C zone?
None required (none required, except as specified in Section 17.34.060) — Atwater Municipal Code § 17.36.070.
What is the minimum lot size in Atwater's C-C zone?
7,500 sq ft (new lots) — Atwater Municipal Code § 17.36.070.
General information, not legal advice.
Ask about an Atwater property in C-C
Ask GoCodebook what you can build at a specific address and get an answer that cites the section.
Ask your question