Skip to content
ChatProjectCodes

Earlier editions: 2026-07

Title 25 — Objective Design and Development Standards

Santa Barbara Municipal Code Ch. 25.06 Architectural Design

Santa Barbara Municipal Code · 2026-10 edition · updated 2026-10-04 · Santa Barbara

Cite as: Santa Barbara Municipal Code Chapter 25.06 · Text as of 2026-10-04

§ 25.06.010. Purpose.

This Chapter sets forth architectural design standards to further refine intended building form and physical character. The styles were created to be harmonious with Santa Barbara's distinctive built environment and were selected to represent the most prevalent existing architectural styles. The Architectural Styles Map requires certain styles in areas of the city including those that are highly visible to the public or adjacent to sensitive historic resources. These standards supplement the standards in Chapter 25.02 (Zones), Chapter 25.04 (Building Types), and Chapter 25.05 (Frontages).

(Ord. 6170, 2/25/2025)

Exceptions & meaning →

§ 25.06.020. General Requirements.

A. Façades. All façades shall be designed in compliance with the standards of this chapter, Chapter 25.05 (Frontages), and Section 25.04.160 (Massing and Façade Composition).

  1. Unless stated otherwise, all subsections within each architectural style group ('style') identified in this chapter apply to all façades of a building, including primary front façades, secondary front façades, interior façades, and interior courtyard façades.

B. Architectural Styles.

  1. One architectural style shall be selected for each new building in compliance with Section 25.01.120 (Architectural Styles Map).

  2. Projects located in Historic Districts, Landmark Districts, or Potential Historic Districts are limited to the architectural styles required for that district, as described in either Chapter 30.57 (Landmark District and Historic District Overlay Zone), or the City's Historic Resource Design Guidelines, as applicable. If an architectural style is required in a Historic District, Landmarks District, or Potential Historic District, but is not available in this chapter, it is not allowed to be approved under this Title.

  3. Projects using styles not included in this chapter are not allowed to be approved under this Title.

  4. The Industrial sub-style is limited to projects in the M-C Manufacturing Commercial or CO-CAR Coastal-Oriented Commercial, Arts, and Recreation base zones as shown on the Architectural Styles Map.

  5. All buildings on a single design site shall use the same style.

C. Elements.

  1. Within each style, the standards for architectural elements apply to each architectural element wherever that element appears on a new building.

  2. Individual element types (e.g., balconies, storefronts) or components (e.g., cornice, brackets) may be included or omitted on any given façade, but where included shall comply with the standards for the selected style, including the stated nominal dimensional standards.

  3. Elements and components are required only where explicitly indicated.

D. All Styles Requirements. The following standards apply to each architectural style group.

  1. Walls.

(a) Structural expansion joints shall be concealed by placement, color selection, or use of façade plane change.

(b) Stucco wall finish shall extend below the weep screed, flush with the wall surface above, and continue for a minimum of two inches below finish grade.

(c) Wall flashing to be anodized or painted to match wall, trim, or other main color of the building.

  1. Skylights.

(a) Skylights shall be curb or deck mounted in line with the roof pitch. Domed skylights are not allowed.

(b) Skylights shall not be publicly visible. Skylights may be screened by the building form, landscape, or parapet.

  1. Windows.

(a) Glazing divisions shall be positioned exterior to glass panes.

  1. Dimensions. Lumber dimensions for trellises and carports are nominal.

  2. Materials and Colors.

(a) Wood and composite wood shall be stained, sealed, or painted.

(b) Where used, metal shall be painted or treated to prevent shiny or reflective finishes.

(c) Paint, textile, and metal colors shall be selected from the Santa Barbara Guide: A Guide to Painting Buildings.

(d) Wrought iron shall have a minimum one-half-inch cross section.

(Ord. 6170, 2/25/2025)

Exceptions & meaning →

§ 25.06.030. Quick Code Guide: Architectural Design Standards.

Before you begin Identify your zone. If you have not done this yet, go back to the Quick Code Guide: Development Standards (Section 25.01.130 ).

Instructions Location
Identify the architectural styles that are allowed at your project location. Section 25.01.120 (Architectural Styles Map)
Identify your architectural style group and select one of the 2 sub-styles within that group to apply Subsections A and B of Section 25.06.040 (Craftsman Style Group), Section 25.06.050 (Mediterranean Style Group), or Section 25.06.060 (Contemporary Style Group)
Comply with the applicable standards for massing and façade composition. Section 25.04.160 (Massing and Façade Composition)
Comply with wall and building roof form standards of selected sub-style. Subsections C–G of Architectural Style
Comply with window and door standards of selected sub-style. Subsections H–K of Architectural Style
Comply with external elements standards and material standards of selected sub-style Subsections L up to Q of Architectural Style

(Ord. 6170, 2/25/2025)

Exceptions & meaning →

§ 25.06.040. Craftsman Style Group.

A. General Description.

  1. Craftsman Sub-Style. The Craftsman style emerged in the American west and was inspired by the English Arts and Crafts movement. The Craftsman bungalow house was prevalent from the 1900s to the 1940s. Since that time, it has been adapted to multi-unit and mixed-use prototypes.

  2. Cottage Sub-Style. Prevalent in the early 20th century, the Cottage style, like Craftsman, was influenced by the English Arts and Crafts movement and its affinity for pre-industrial models. In Santa Barbara, the Cottage style accommodates a range of primarily Northern European vernacular expressions. Windows, bay windows, balconies, porches, and materials are based on elements used in these traditions.

B. Character Description.

  1. Craftsman.
Massing of two and a half stories or less
Low-pitched roofs with deep eaves and exposed rafter tails
Horizontally proportioned openings made from ganged vertical windows
Emphasis on natural-appearing materials, including composite wood shingles
Asymmetrical composition with wall plane broken by projecting gable ends
Wall plane broken by projecting and/or recessed elements
  1. Cottage.
Massing of two and a half stories or less
Asymmetrical massing with front-facing gables
Steeply-pitched shingle roof with low eaves; minimal projection at eave and rake
Windows with evenly-spaced divided lites
Stucco walls with or without half-timbering
Mix of arched doors and square, though occasionally segmented arched, windows
Elements of Craftsman Style
Example Building Elevation: Crafstman

C. Wall.

  1. Craftsman.

Height Limitation

Building Height 2.5 stories max.
Trim 1 Trim 1 Trim 1
Width 6" min. A
Base Base Base
Height 1'-0" min.; 1 story max. B
Required Articulation Projecting Profile/Molding C
Base is required for this sub-style.

Note:

1 Trim not required on portions of buildings where stucco, masonry, or stone is the primary wall material.
Elements of Cottage Style
Example Building Elevation: Cottage
  1. Cottage.

Height Limitation.

Building Height 2.5 stories max.
Trim 2 Trim 2 Trim 2
Edge Trim Width 4" min. D
Half-Timbering Width 8" min. E
Base Base Base
Height 1 story max. F
Required Articulation Projecting Profile/Molding G
Base is not required for this sub-style.

Note:

2 Trim not required on portions of buildings where stucco, masonry, or stone is the primary wall material.

D. Building Roof.

Gable End Elevation
  1. Craftsman.

Roof Form

Type Gable, Hip, Shed 3
Pitch 3:12 min.; 8:12 max. H
  1. Cottage.

Roof Form

Type Gable, Shed 4
Pitch 8:12 min. H

Notes:

3 High side of shed roof must terminate into wall.
4 High side of shed roof must terminate into wall.

E. Rake.

Rake Section: Craftsman with Bracket
Rake Section: Cottage
  1. Craftsman.

Height

Fascia 10" min. I
Bracket Bracing Member 4" min. J
Horizontal Projection Horizontal Projection Horizontal Projection
To Fascia: Main Roof Form 1'-8" min. 3'-0" max; K
To Fascia: Dormer 8" min. 1'-2" max; K
Bracket Projection Beyond Fascia No min.; 1'-0" max. L
  1. Cottage.

Height

Fascia 8" min. M
Horizontal Projection Horizontal Projection Horizontal Projection
Projection to Fascia 8" min. N

F. Eave.

Open Eave Elevation: Craftsman
  1. Craftsman.
Standards Open Eave Closed Eave
Height
Rafter 8" min. N/A O
Horizontal Projection 5 Horizontal Projection 5 Horizontal Projection 5 Horizontal Projection 5
Main Roof Form 2'-6" min. N/A P
Dormer 8" min. N/A P

Note:

5 Horizontal projection includes gutter, where occurs.
Closed Eave Elevation: Cottage
Open Eave Elevation: Cottage
  1. Cottage.
Standards Open Eave Closed Eave
Height Height Height Height
Rafter 8" min. N/A Q
Horizontal Projection 6 Horizontal Projection 6 Horizontal Projection 6 Horizontal Projection 6
Overall 1'-0" min. 1'-0" min. R

Note:

6 Horizontal projection includes gutter, where occurs.

G. Parapet: All. Flat roofs with parapets are not allowed in this style group. See Subsection E (Rake) and Subsection F (Eave) for standards applicable to sloped roofs.

H. Windows.

Typical Window Elevation: Craftman (Shown with 6 over 1 Glazing Division) Typical Window Elevation: Cottage (Shown with 20 Parts Glazing Division)
  1. All.

Opening Proportion, Height S to Width T

Typical Window
Ground Floor 2:1 min.
Typical Upper Floor 7:4 min.
Accent Window
Rectangle 3:2 min. (2'-6" max. width)
Square 1:1 min. (3'-0" max. width)
Ganged Window 3:5 min.
Picture Window 6:5 min.
Dormer Window 7:4 min.
Window Window Window
Sash Widths
Rail 2" min. U
Stile 2" min. V
Trim Widths 7
Head 6" min. W
Jamb 6" min. X
Apron 3" min. Y
Ganged Window Elevation: Craftsman with 4 over 1 and 6 over 1 Glazing Divisions

Window Frame Recess

Depth 2" min. from face of surround to face of sash
Sill Projection Sill Projection
Depth 2" min. from face of surround
Pediment Pediment
Allowed No
Mullions Mullions
Mullions required between ganged windows.

Note:

7 Trim required for windows only on buildings or parts of buildings with lap siding.
Bay Window Plan: Chamfered Bay Window Plan: Square
  1. Craftsman.

Opening

Shape Rectangular
Window Window
Operation Double-Hung, Single-Hung, Awning, Casement, Fixed
Glazing Divisions 4 over 1, 6 over 1, or 10 over 1
Width of lites shall be no greater than their height.
  1. Cottage.

Opening

Shape Rectangular, Arched
Window Window
Operation Double-Hung, Single-Hung, Awning, Casement, Fixed
Glazing Divisions 6 parts min.; 24 parts max.
Width of lites shall be no greater than their height.

I. Bay Windows: All.

Bay Window Elevation

Form

Type Square, Chamfered
Interior Angle for Chamfered Form 30 degrees min.; 55 degrees max. Z
Continuous horizontal articulation on building shall wrap bay window form.
Dimensions Dimensions Dimensions
Width 6'-0" min.; 12'-0" max. A
Depth 1'-0" min.; 4'-0" max. B
Bay window that does not extend to grade shall be supported on brackets.
Bay window form shall be vertically continuous from lowest bay window to highest bay window.
Allowed Cornice Treatments Allowed Cornice Treatments Allowed Cornice Treatments
Bay window stops below building eave (provide roof or cornice for bay window).
Corner Placement Corner Placement Corner Placement
At building corner, square bay window may be rotated 45 degrees.
When wrapping a corner, chamfered bay window may incorporate up to 5 faces instead of the typical 3.

J. Dormers.

Dormer Elevation: Craftsman
  1. Craftsman.

Roof Form

Type Shed
Pitch 3:12 min.; 7:12 max.
Horizontal Projection Horizontal Projection Horizontal Projection
Rake See Subsection E.1 (Rake) for rake standards. C
Eave See Subsection F.1 (Eave) for eave standards.
Placement Placement Placement
Setback from Side Façade 3'-0" min.
Setback from Façade to Face of Dormer 1'-0" min.
Dormers shall not interrupt continuity of main building roof eave.
Window Window Window
See Subsection H (Windows) for window standards.
Dormer Elevation: Cottage Shown with Gable Roof
  1. Cottage.

Roof Form

Type Gable, Hip
Pitch 6:12 min.; 10:12 max. D
Horizontal Projection Horizontal Projection Horizontal Projection
Rake See Subsection E.2 (Rake) for rake standards.
Eave See Subsection F.2 (Eave) for eave standards.
Placement Placement Placement
Setback from Side Façade 3'-0" min.
Setback from Façade to Face of Dormer 1'-0" min.
Dormers shall not interrupt continuity of main building roof eave.
Window Window Window
See Subsection H (Windows) for window standards.

K. Entry Doors.

Vision Glass Door Elevation with Two Panels and Square Span Half Glass Door Elevation with Three Panels and Sidelights Full Glass Door Elevation with Transom: Craftsman
  1. Craftsman.

Door

Number of Panels 2 min. 8
Lite Types/Glazing Divisions Lite Types/Glazing Divisions Lite Types/Glazing Divisions
Vision Glass 3 parts min.
Half Glass 6 parts min.
Full Glass 3 parts min. over 1
Surround Surround Surround
Span Type Lintel
Head Width 6" min. E
Jamb Width 4" min. F
Glazed Openings Glazed Openings Glazed Openings
Transom Allowed
Sidelights Allowed
Placement Placement Placement
No portion of door shall be allowed within 1'-6" of outside corners of building.
Doors shall be centered along width of balconies and arches, where occurs.

Note:

8 Panels not required for full glass lite type.
  1. Cottage.

Door

Number of Panels 2 min. 9
Lite Types/Glazing Divisions Lite Types/Glazing Divisions Lite Types/Glazing Divisions
Vision Glass 4 parts min.
Half Glass 8 parts min.
Full Glass 16 parts min.
Surround Surround Surround
Span Type Lintel, Arch
Head Width 6" min. E
Jamb Width 4" min. F
Glazed Openings Glazed Openings Glazed Openings
Transom Allowed
Sidelights Allowed
Placement Placement Placement
No portion of door shall be allowed within 1'-6" of outside corners of building.
Doors shall be centered along width of balconies and arches, where occurs.

Note:

9 Panels not required for full glass lite type.

L. Columns/Pilasters.

One-Story Porch with Square Tapered Column and Capital Connection: Craftsman
  1. Craftsman.

Columns + Pilasters

Shape Square, Square Tapered
Width/Diameter 9" min. each
Spacing 9'-6" min., 12'-0" max. on center G
Pedestal Height 10 3'-0" min.
Entablature/Beam Connection Capital, Mortise and Tenon
Columns may be paired.
Columns must not span multiple stories.
Additional Features Additional Features Additional Features
Paneling Allowed
Fluting Not Allowed
Entablature Height Entablature Height Entablature Height
Topmost Floor 1'-6" min. H
Intermediate Floor 10" min.
Guard/Railing Guard/Railing Guard/Railing
Allowed Types Square, Flat Sawn
Width Between Posts 3'-0" min. on center

Note:

10 Pedestal may be omitted.
One-Story Porch with Paired Square Columns on Pedestals and Mortise and Tenon Connection: Cottage
  1. Cottage.

Columns + Pilasters

Shape Square
Width/Diameter 6" min. each
Spacing 8'-0" max. on center I
Pedestal Height 11 3'-0" min. J
Entablature/Beam Connection Capital, Mortise and Tenon
Columns may be paired.
Columns must not span multiple stories.
Additional Features Additional Features Additional Features
Paneling Allowed
Fluting Not Allowed
Entablature Entablature Entablature
Topmost Floor 1'-6" min. K
Intermediate Floor 10" min.
Guard/Railing Guard/Railing Guard/Railing
Allowed Types Square, Flat Sawn
Width Between Posts 3'-0" min. on center

Note:

11 Pedestal may be omitted.

M. Balconies: All.

Juliet Balcony with Flat Sawn Railing, Front Elevation

Allowed Types Type 1 - Juliet Balcony

Inward-swinging door with full glazing required Inward-swinging door with full glazing required L
Base Height 3" min. M
Base Projection 4" min.; 2'-0" max.
Type 2 - Occupiable Balcony Type 2 - Occupiable Balcony Type 2 - Occupiable Balcony
Clear Depth 6'-0" min.
Area 48 sq. ft. min.
Recess into Façade 4'-6" max.
Overall Width 10'-0" max.
Occupiable Balcony with Flat Sawn Railing, Front Elevation
Occupiable Balcony with Square Railing, Front Elevation

Guard/Railing

Allowed Types Square, Flat Sawn
Height Per Building Code N
Width Between Posts 3'-0" min. on center O
Brackets/Supports Brackets/Supports Brackets/Supports
Allowed Types Brackets, Cantilevered Beams
Depth 80% of projection depth at bracket, min.
Height 50% of bracket depth, min. P
Spacing 6'-0" on center; max. Q

N. Storefronts: All.

Storefront Section Storefront Elevation

Width

Storefront Module 12 10'-0" min.; 25'-0" max. R
Display Window 3'-0" min.; 6'-0" max. S
Distance Between Storefront Modules 1'-0" min.; 6'-0" max. T
Height Height Height
Overall 13'-0" min. U
Head Height 10'-0" min. V
Cornice 10" min. W
Signage Band 1'-6" min. X
Bulkhead 1'-0" min.; 2'-0" max. Y
Horizontal Recess Horizontal Recess Horizontal Recess
Depth 6" min.; 1'-0" max. 13 Z
Bulkhead shall be continuous, unless divided by pilaster, and align with base height of building (if any).
Cornice shall be continuous. Cornice shall be continuous. Cornice shall be continuous.

Notes:

12 May be expressed as a pilaster. See Subsection L (Columns/Pilasters).
13 No max. depth for residential entries.

O. Awning: All.

Awning Section: Craftsman Awning Elevation: Craftsman

Awning

Eave Height 6" min. A
Horizontal Projection 14 3'-0" min. B
Required Support Elements Brackets Brackets
Bracket Width 4" min. C
Roof Pitch 3:12 min. D

Note:

14 Horizontal projection includes gutter, where occurs.

P. Trellises and Carports: All.

Dimensions

Post 8" x 8" min. E
Main and Cross Beam 4" x 8" min. 15 F
Rafter 2" x 4" min. G
Purlin or Lattice 2" x 2" min. H
Overhang Overhang I
Beams 3'-0" max.
Purlin or Lattice 2'-0" max.
Trellis 1'-6" max.

Note:

15 Paired 2" x 8" members are allowed when placed on both sides of the supporting posts.

Q. Materials.

  1. Craftsman.
Element Allowed Materials
Building Walls Building Walls
Cladding Shingle or lap siding (wood, composite wood, fiber cement), stucco
Base or Foundation Stucco, stone, cast stone, colored or painted concrete
Roof and Roof Elements Roof and Roof Elements
Roofing Shingles (composite wood, slate, dimensional or luxury asphalt shingles to mimic the look of wood or slate); standing seam metal (black, white, or reflective metal finishes are prohibited)
Rake and Eave Wood, composite wood
Cornice Wood, composite wood
Brackets Wood, composite wood, fiberglass
Gutter Half-round copper, metal
Windows, Bay Windows, and Entry Doors Windows, Bay Windows, and Entry Doors
Trim or Surround Wood, composite wood, fiber cement
Entry Door Wood, composite wood, aluminum-clad wood, fiberglass
Window Frames Wood, aluminum-clad wood
Glazing Clear glass; shall not be tinted, mirrored, or colored
Garages Garages
Garage Door 16 Wood, composite wood, fiberglass
Balconies Balconies
Post, Handrail, Fascia, and Support Members Wood, composite wood, solid metal
Railing Wood, composite wood, metal
Porches Porches
Columns Wood, composite wood, sandstone, metal
Railing Wood, composite wood, solid metal
Storefronts Storefronts
Storefront Module Wood, composite wood, metal, fiberglass
Storefront Base (Bulkhead) Wood, brick, stone, tile, fiber cement
Chimneys Chimneys
Cap Copper, steel
Body Brick, stone, cast stone (including veneers of any of the above)
Exterior Building Lighting Exterior Building Lighting
Body and Mount Wrought iron, metal
Shield Clear, translucent, punched, louvers
Stairs and Ramps Stairs and Ramps
Treads and Risers Wood, composite wood, stucco, brick, stone
Handrails Wood, composite wood, stucco, stone, wrought iron, metal
Trellises and Carports Trellises and Carports
Spanning Members Wood, composite wood
Trellis Posts Wood, composite wood
Carport Support Posts Wood, composite wood, stucco
Trash Enclosure Trash Enclosure
Walls Wood, composite wood, stucco
Fences and Hedges Fences and Hedges
Walls Stucco, brick, stone (faux manufactured stone veneer is prohibited), concrete block (coated and painted or pigmented to match the main building)
Fences 17 Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)

Notes:

16 Metal roll up doors are allowed only if not publicly visible. Metal security grilles are allowed for parking structures.
17 Publicly visible fences may not be chain link unless screened with vines.
  1. Cottage.
Element Allowed Materials
Building Walls Building Walls
Cladding Wood, composite wood, stucco, brick, stone, fiber cement
Base or Foundation Stucco, brick, stone, cast stone, colored or painted concrete
Roof and Roof Elements Roof and Roof Elements
Roofing Shingles (composite wood, slate, dimensional or luxury asphalt shingles to mimic the look of wood or slate)
Rake and Eave Wood, composite wood
Cornice Wood, composite wood
Brackets Wood, composite wood, fiberglass
Gutter Half-round copper, metal
Windows, Bay Windows, and Entry Doors Windows, Bay Windows, and Entry Doors
Trim or Surround Wood, composite wood, fiber cement
Entry Door Wood, composite wood, aluminum-clad wood, fiberglass
Window Frames Wood, aluminum-clad wood
Glazing Clear glass; shall not be tinted, mirrored, or colored
Garages Garages
Garage Door 18 Wood, composite wood, fiberglass
Balconies Balconies
Post, Handrail, Fascia, and Support Members Wood, composite wood, solid metal
Railing Wood, composite wood, metal
Porches Porches
Columns Wood, composite wood, metal, fiberglass
Railing Composite wood, wood, solid metal
Storefronts Storefronts
Storefront Module Wood, composite wood, metal
Storefront Base (Bulkhead) Wood, stucco, brick, fiber cement
Chimneys Chimneys
Cap Copper, steel
Body Brick, stone, cast stone (including veneers of any of the above)
Exterior Building Lighting Exterior Building Lighting
Body and Mount Wrought iron, metal
Shield Clear, translucent, punched, louvers
Stairs and Ramps Stairs and Ramps
Treads and Risers Wood, composite wood, stucco, brick, stone
Handrails Wood, composite wood, stucco, stone, wrought iron, metal
Trellises and Carports Trellises and Carports
Spanning Members Wood, composite wood
Trellis Posts Wood, composite wood
Carport Support Posts Wood, composite wood, stucco
Trash Enclosure Trash Enclosure
Walls Wood, composite wood, stucco
Fences and Hedges Fences and Hedges
Walls Stucco, brick, stone (faux manufactured stone veneer is prohibited), concrete block (coated and painted or pigmented to match the main building)
Fences 19 Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)

Notes:

18 Metal roll up doors are allowed only if not publicly visible. Metal security grilles (including roll up function) are allowed for parking structures.
19 Publicly visible fences may not be chain link unless screened with vines.

(Ord. 6170, 2/25/2025)

Exceptions & meaning →

§ 25.06.050. Mediterranean Style Group.

A. General Description.

  1. Spanish Colonial Revival Sub-Style. The Spanish Colonial Revival style is a reflection of Santa Barbara's Spanish architectural tradition. The sub-style adheres to simple building massing, the impression of traditional masonry construction, prominence of clay tile roof forms, and craftsmanship with an emphasis on raw materials.

  2. Italian Mediterranean Sub-Style. While similar to the Spanish Colonial Revival style in terms of cladding and materials, the Italian Mediterranean style is expressed through the symmetrical and formal composition of openings, the cornice detailing at rakes and eaves, and the types of columns and pilasters used.

B. Character Description.

  1. Spanish Colonial Revival
Flat roofs or low-pitched gabled and/or hipped roofs, often stepped and with simple eave and cornice details
Red cap-and-pan, terra-cotta clay roof tile installed with a scattered field pattern, random mortar lifts, and selectively placed booster tile
Flat, rectilinear wall plane with symmetrical or asymmetrical compositions of vertically proportioned punched openings without trim
Stucco as primary façade material with stucco or wood attached elements, and decorative tile at surrounds/stairs
Architectural details and materials display influence of Spanish and Moorish architecture
Ornamental elements, such as chimneys, vents, and gutters
  1. Italian Mediterranean
Low-pitched hipped roofs clad in red tile with boxed eaves, often bracketed
Flat, rectilinear wall plane with vertically proportioned punched openings without trim
Stucco as primary façade material with stucco, wood, or metal attached elements
Formal and/or symmetrical composition of doors and windows
Use of classical orders, including columns and pilasters, to accentuate entrances and openings
Elements of Spanish Colonial Revival

C. Wall: All.

Base Base is not required for this style group. Wall Projections Wall projections are allowed, but not required.

Depth 1'-0" min. A
Provide lintel for full width of projection. Provide lintel for full width of projection. B

Elements of Italian Mediterranean Style

D. Building Roof: All.

Gable End Elevation
Standards Sloped Roof Flat Roof Flat Roof
Roof Form Roof Form Roof Form Roof Form
Type Gable, Hip, Shed 1 Flat 2,3
Pitch 3:12 min.; 6:12 max. N/A C
Applicable Subsections Applicable Subsections Applicable Subsections Applicable Subsections
E. Rake Applies N/A
F. Eave Applies N/A
G. Parapet N/A Applies
Roof Tile Installation Standards Roof Tile Installation Standards Roof Tile Installation Standards Roof Tile Installation Standards
Starter course shall be double tiled, min.
Unpigmented mortar required at birdstops, hips, and ridges.
Attic Vents Attic Vents Attic Vents Attic Vents
Placement Centered within gable Centered within gable D

Notes:

1 High side of shed roof must terminate into wall.
2 Flat roof parapets that are publicly visible cannot exceed 25% of the building length, or 25' max., whichever is greater.
3 In the El Pueblo Viejo Landmark District, flat roof parapets cannot be publicly visible.
Rake Elevation (with Ornamental Scored Scallop Pattern)
Rake Section (with Ornamental Scored Scallop Pattern)

E. Rake: All

Allowed Ornament 4

Height 1'-0" min. E
Projection to Rake Tile 3" min. F

Note:

4 Scored scallop pattern shall align with tile breaks, where occurs.

F. Eave.

Returned Eave Section: Italian Mediterranean
Open Eave Section: Italian Mediterranean
Closed Eave Section: Spanish Colonial Revival
  1. Spanish Colonial Revival.
Standards Closed Open Returned Returned
Horizontal Projection 5 Horizontal Projection 5 Horizontal Projection 5 Horizontal Projection 5 Horizontal Projection 5
Overall 3" min. N/A N/A G

Note:

5 Horizontal projection includes gutter.
Returned Eave Elevation: Italian Mediterranean
Open Eave Elevation: Italian Mediterranean
Closed Eave Elevation: Italian Mediterranean
  1. Italian Mediterranean.
Standards Closed Open Returned Returned
Horizontal Projection 6 Horizontal Projection 6 Horizontal Projection 6 Horizontal Projection 6 Horizontal Projection 6
Overall 1'-0" min. 3'-0" min. 2'-6" min. H
Fascia/Cornice Molding Fascia/Cornice Molding Fascia/Cornice Molding Fascia/Cornice Molding Fascia/Cornice Molding
Height 1'-0" min. N/A 6" min. I
Allowed Rafter Tails and Supports Allowed Rafter Tails and Supports Allowed Rafter Tails and Supports Allowed Rafter Tails and Supports Allowed Rafter Tails and Supports
Type N/A Shaped, Plumb Cut Shaped
Height N/A 8" min. 1'-0" min. J
Width N/A 3" min. 3" min. K
Spacing N/A 2'-0" max. on center 2'-0" max. on center L
Placement N/A Below decking Below fascia

Note:

6 Horizontal projection includes gutter.

G. Parapet.

Parapet Section: Spanish Colonial Revival Parapet Elevation: Spanish Colonial Revival
  1. All.

Allowed Ornament

Type Wall Moulding at Top of Parapet Wall Moulding at Top of Parapet
Height 2'-0" max. M
Projection 1'-0" max. N
Placement Continuous with Parapet Cap Continuous with Parapet Cap
Sloped Roof Parapet Section: Spanish Colonial Revival
Sloped Roof Parapet Elevation: Spanish Colonial Revival
  1. Spanish Colonial Revival.

Sloped Roof with Parapet

Eave Projection See Subsection F.1 (Eave) for eave standards. O
Parapet Height 2'-6" min. P
Sloped roof shall extend to reach full height of parapet.
Sloped roof portion shall comply with all standards applicable to sloped roofs in Subsection D (Building Roof).

Sloped Roof Parapet Section: Italian Mediterranean

Sloped Roof Parapet Elevation: Italian Mediterranean

  1. Italian Mediterranean.

Sloped Roof with Parapet

Eave Projection, Profile, and Supports See Subsection F.2 (Eave) for eave standards. Q
Parapet Height 2'-6" min. R
Sloped roof shall extend to reach full height of parapet.
Sloped roof portion shall comply with all standards applicable to sloped roofs in Subsection D (Building Roof).

H. Windows: All.

Typical Window Elevation with 8 Parts Glazing Divisions: Spanish Colonial Revival Ganged Window Elevation with 6 Parts Glazing Divisions: Italian Mediterranean

Opening Proportion, Height S to Width T Typical Window

Ground Floor 2:1 min. 2:1 min.
Typical Upper Floor 7:4 min. 7:4 min.
Accent Window Accent Window Accent Window
Rectangle 3:2 min. (2'-6" max. width) 3:2 min. (2'-6" max. width)
Square 1:1 min. (3'-0" max. width) 1:1 min. (3'-0" max. width)
Ganged Window 3:5 min. 3:5 min.
Picture Window 6:5 min. 6:5 min.
Dormer Window 7:4 min. 7:4 min.
Opening Opening Opening
Shape Rectangular, Arched Rectangular, Arched
Window Window Window
Operation Casement, Fixed Casement, Fixed
Glazing Divisions 7 6 or 8 parts 6 or 8 parts
Width of lites shall be no greater than their height.
Sash Widths Sash Widths Sash Widths
Rail 2" min. U
Stile 2" min. V
Moulding Widths
Head 2" min. W
Jamb 2" min. X
Apron None
Window Frame Recess Window Frame Recess Window Frame Recess
Depth 2" min. from face of surround to face of sash. 2" min. from face of surround to face of sash.
Sill Projection Sill Projection Sill Projection
Depth 2" min. from face of surround. 2" min. from face of surround.
Pediment Pediment Pediment
Allowed Italian Mediterranean only Italian Mediterranean only
Mullions Mullions Mullions
Mullions required between ganged windows.
Placement Placement Placement
No portion of window shall be allowed within 1'-6" of outside corners of building.

Note:

7 Glazing divisions for picture and accent windows may be one part. Italian Mediterranean may also have 10, 12, or 15 equal parts.

I. Bay Windows: All.

Bay Window Plan
Bay Window Elevation

Form

Type Square Square
Continuous horizontal articulation on building shall wrap bay window form.
Dimensions Dimensions Dimensions
Width 6'-0" min.; 12'-0" max. Y
Depth 1'-0" min.; 4'-0" max. Z
Height Height Height
Bay window may extend from second story to top story.
Bay window may occupy first story on buildings less than 3 stories tall.
Bay window that does not extend to grade shall be supported on brackets.
Bay window form shall be vertically continuous from lowest bay window to highest bay window.
Allowed Cornice Treatments Allowed Cornice Treatments Allowed Cornice Treatments
Building parapet wraps bay window. Building parapet wraps bay window. Building parapet wraps bay window.
Bay window stops below building eave (provide roof or cornice for bay window).
Bay window terminates into building eave (bay window shall not project vertically or horizontally beyond building eave).

J. Dormers: All.

Dormer Elevation with Gable Roof

Roof Form

Type Gable
Pitch 3:12 min.; 6:12 max. A
Horizontal Projection Horizontal Projection Horizontal Projection
Rake See Subsection E (Rake) for rake standards. See Subsection E (Rake) for rake standards.
Eave See Subsection F (Eave) for eave standards. See Subsection F (Eave) for eave standards.
Placement Placement Placement
Setback from Side Façade 3'-0" min. 3'-0" min.
Setback from Façade to Face of Dormer 1'-0" min. 1'-0" min.
Dormers shall not interrupt continuity of main building roof eave.
Window Window Window
See Subsection H (Windows) for window standards.

K. Entry Doors: All.

Vision Glass Door Elevation with Two Panels and Arched Span Half Glass Door Elevation with Two Panels and Sidelights Full Glass Door Elevation with Transom and Entablature: Italian Mediterranean

Door

Number of Panels 2 min. 8
Frame Recess 4" min. from face of door to face of surround.
Lite Types/Glazing Divisions Lite Types/Glazing Divisions
Vision Glass 0 parts min.; 4 parts max.
Half Glass 6 parts
Full Glass 8 parts min.; 15 parts max.
Surround Surround
Span Type Square, Arch
Glazed Openings Glazed Openings
Transom Allowed
Sidelights Allowed
Entablature Italian Mediterranean only
Pediment Italian Mediterranean only
Placement Placement
No portion of door shall be allowed within 1'-6" of outside corners of building.
Doors shall be centered along width of balconies and arches, where occurs.

Note:

8 Panels not required for full glass lite type.

L. Columns/Pilasters.

One-Story Porch with Square Column and Capital Connection: Spanish Colonial Revival
  1. Spanish Colonial Revival

Columns + Pilasters

Shape Square, Round
Width/Diameter 8" min. each
Spacing 9'-0" max. on center B
Pedestal Height 9 3'-0" min. C
Entablature/Beam Connection Capital, Bracket, Corbel Capital, Bracket, Corbel
Columns must not span multiple stories. Columns must not span multiple stories. Columns must not span multiple stories.
Additional Features Additional Features Additional Features
Paneling Allowed
Fluting Not Allowed
Entablature Height Entablature Height Entablature Height
Topmost Floor 1'-6" min. D
Intermediate Floor 10" min.
Guard/Railing Guard/Railing Guard/Railing
Allowed Types Square, Turned (includes balustrade), Wall Square, Turned (includes balustrade), Wall
Width Between Posts 3'-0" min. on center

Note:

9 Pedestal may be omitted.
One-Story Porch with Square Column and Capital Connection: Italian Mediterranean
  1. Italian Mediterranean

Columns + Pilasters

Shape Square, Round, Tuscan (Tapered)
Width/Diameter 8" min. each
Spacing 9'-0" max. on center E
Pedestal Height 10 3'-0" min.
Entablature/Beam Connection Capital
Columns must not span multiple stories. Columns must not span multiple stories. Columns must not span multiple stories.
Additional Features Additional Features Additional Features
Paneling Allowed
Fluting Not Allowed
Entablature Height Entablature Height Entablature Height
Topmost Floor 1'-6" min. F
Intermediate Floor 10" min.
Guard/Railing Guard/Railing Guard/Railing
Allowed Types Square, Turned (includes balustrade), Wall Square, Turned (includes balustrade), Wall
Width Between Posts 3'-0" min. on center 3'-0" min. on center

Note:

10 Pedestal may be omitted. Pedestal may be omitted.

M. Balconies: All.

Juliet Balcony with Decorative Metal Railing, Front Elevation Recessed Balcony with Stucco Wall, Front Elevation
Balcony with Square Railing, Front Elevation Balcony with Turned Railing, Front Elevation

Allowed Types Type 1 - Juliet Balcony

Inward-swinging door with full glazing required Inward-swinging door with full glazing required G
Base Height 3" min. H
Base Projection 4" min.; 2'-0" max.
Type 2 - Occupiable Balcony Type 2 - Occupiable Balcony Type 2 - Occupiable Balcony
Clear Depth 6'-0" min.
Area 48 sq. ft. min.
Recess into Façade 6'-8" max.
Overall Width 10'-0" max.
Guard/Railing Guard/Railing Guard/Railing
Allowed Types Square, Turned (includes balustrade), Wall 11
Height Per Building Code I
Width Between Posts 3'-0" min. on center J
Brackets/Supports Brackets/Supports Brackets/Supports
Allowed Types Brackets, Cantilevered Beams
Depth 80% of projection depth at bracket, min.
Height 50% of bracket depth, min. K
Spacing 4'-0" on center, max. L

Note:

11 Wall is allowed only for recessed balconies and shall not be used for Juliet Balcony.

N. Store fronts: All.

Storefront Section Storefront Elevation

Width

Storefront Module 12 10'-0" min.; 25'-0" max. M
Display Window 3'-0" min.; 6'-0" max. N
Distance Between Storefront Modules 1'-6" min.; 6'-0" max. O
Height Height Height
Overall None
Head Height 10'-0" min. P
Cornice None
Signage Band None
Bulkhead 1'-0" min.; 2'-0" max. Q
Horizontal Recess Horizontal Recess Horizontal Recess
Depth 1'-0" min.; 2'-0" max 13 R
Bulkhead shall be continuous, unless divided by pilaster, and align with base height of building (if any).
For arched storefronts, see Section 25.05.130 (Arcades).

Notes:

12 May be expressed with pilasters. See Subsection L (Columns/Pilasters).
13 No max. depth for residential entries.

O. Awnings: All.

Awning Section Awning Elevation with Straight Valance

Awning Design

Horizontal Projection 3'-0" min. S
Offset from Opening 6" max. T
Surface Shape 14 Angled Surface with Open Sides Angled Surface with Open Sides
Valance Shape Straight Straight
Required Support Elements Finials 15 Finials 15
The bottom edge of the valance shall fall below the window or door head height, unless this conflicts with minimum clear height standards.
Supports shall not be installed horizontally, and shall angle up from the point of wall attachment at an angle equal to the slope of the awning surface.

Notes:

14 Horizontally segmented, curved, and domed awnings are prohibited, except that curved awnings are allowed for an arched opening if placed within the arch such that the form and depth of the arch are still visible.
15 Finials must be spear points in the Spanish Colonial Revival sub-style.

P. Trellises and Carports: All.

Trellis Diagram

Dimensions

Post 8" x 8" min. U
Main and Cross Beam 4" x 8" min. 16 V
Rafter 2" x 4" min. W
Purlin or Lattice 2" x 2" min. X
Overhang Overhang Y
Beams 3'-0" max.
Purlin or Lattice 2'-0" max.
Trellis 1'-6" max.

Note:

16 Paired 2" x 8" members are allowed when placed on both sides of the supporting posts.

Q. Materials.

  1. Spanish Colonial Revival.
Element Allowed Materials
Building Walls Building Walls
Cladding Stucco
Accent Materials Stone, tile
Projection Materials Wood, cast-stone
Roof and Roof Elements Roof and Roof Elements
Roofing 17 Two-piece (cap-and-pan)terra-cotta clay barrel tiles
Rake and Eave Wood, composite wood, stucco
Cornice Wood, composite wood, stucco
Brackets and Corbels Wood, composite wood, stucco, fiberglass
Parapet Cap Stucco, two-piece (cap-and-pan) terra-cotta clay barrel tiles
Finials Metal (copper, cast iron, steel)
Attic and Mechanical Vents Attic and Mechanical Vents
Vent Masonry, terra-cotta clay barrel tiles, wood louvers, wrought iron grill
Gutters, Downspouts, and Leaderheads Gutters, Downspouts, and Leaderheads
Gutter Profile Half-round
Downspout Profile Round
Materials Copper 18 , metal
Windows, Bay Windows, and Entry Doors Windows, Bay Windows, and Entry Doors
Entry Door Wood, composite wood, aluminum-clad wood, fiberglass
Window Frames Wood, aluminum-clad wood, steel
Door/Window Surrounds Stucco, stone, cast stone, tile
Sill Stucco, stone, cast stone
Glazing Clear glass; shall not be tinted, mirrored, or colored
Garages Garages
Garage Door 19 Wood, composite wood, fiberglass
Balconies Balconies
Post, Handrail, Fascia, Railing, and Brackets Wood, composite wood, wrought iron, metal 20
Deck Soffit Wood, composite wood, stucco, wrought iron, tile (glazed, terra-cotta), metal
Porches Porches
Columns Wood, composite wood, stucco fiberglass, metal
Railing Wood, composite wood, wrought iron
Storefronts Storefronts
Storefront Module Wood, composite wood, metal
Storefront Base (Bulkhead) Stucco, tile
Chimneys
Cap Stucco, terra-cotta clay barrel tiles, copper, steel
Body Stucco, brick, stone, cast stone (including veneers of any of the above)
Exterior Building Lighting Exterior Building Lighting
Body and Mount Wrought iron, metal
Shield Clear, translucent, punched, louvers
Stairs and Ramps Stairs and Ramps
Treads and Risers Wood, composite wood, stucco, brick, stone, tile, concrete 20
Handrails Wood, composite wood, stucco stone, wrought iron, metal
Trellises and Carports Trellises and Carports
Spanning Members Wood
Trellis Posts Wood
Carport Support Posts Wood, composite wood, stucco,
Connections Steel, iron
Trash Enclosure Trash Enclosure
Walls Wood, composite wood, stucco
Fences and Hedges Fences and Hedges
Walls Stucco, stone (faux manufactured stone veneer is prohibited)
Fences 21 Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)
Stucco wall finish shall be smooth trowel, with 1/2" to 3/4" bull-nosed corners.
Accent tile shall be 6" x 6" minimum. Accent tile shall be 6" x 6" minimum.
Where used, "metal" and "wrought iron" shall be solid metal (not hollow tube).

Notes:

17 Applies to pitched roof forms; visible birdstops not allowed.
18 Required on façades facing rights-of-way and community open spaces.
19 Metal roll up doors are allowed only if not publicly visible. Metal security grilles are allowed for parking structures.
20 Allowed on façades not facing streets and community open spaces.
21 Chain link fences are prohibited within the EI Pueblo Viejo Landmark District. In other locations, publicly visible chain link fences are prohibited unless screened with vines.
  1. Italian Mediterranean.
Element Allowed Materials
Wall Wall
Cladding Stucco
Accent Materials Tile, stone
Roof and Roof Elements Roof and Roof Elements
Roofing 22 Two-piece (cap-and-pan) terra-cotta clay barrel tiles
Rake and Eave Wood, composite wood, stucco
Cornice Wood, composite wood, stucco, cast stone, fiberglass
Brackets and Corbels Wood, composite wood, stucco, fiberglass
Parapet Cap Stucco, two-piece (cap-and-pan) terra-cotta clay barrel tiles
Finials Metal (copper, cast iron, steel)
Attic and Mechanical Vents Attic and Mechanical Vents
Vent Masonry, terra-cotta clay barrel tiles, wood louvers, wrought iron grill
Gutters, Downspouts, and Leaderheads Gutters, Downspouts, and Leaderheads
Gutter Profile Half-round
Downspout Profile Round
Materials Copper 23 , metal
Windows, Bay Windows, and Entry Doors Windows, Bay Windows, and Entry Doors
Entry Door Wood, composite wood aluminum-clad wood, steel, fiberglass
Window Frames Wood, aluminum-clad wood, steel
Door/Window Surrounds Stucco, stone, cast stone, tile
Sill Stucco, stone, cast stone
Glazing Clear glass; shall not be tinted, mirrored, or colored
Garages Garages
Garage Door 24 Wood, composite wood, fiberglass
Balconies Balconies
Post, Handrail, Fascia, Railing, and Brackets Wood, composite wood, cast stone, wrought iron, metal, fiberglass
Deck Soffit Wood, composite wood, stucco, tile (glazed, terra-cotta), wrought iron, metal
Porches Porches
Columns Wood, composite wood, stucco, cast stone, metal, fiberglass
Railing Wood, composite wood, cast stone, wrought iron, fiberglass
Storefronts Storefronts
Storefront Module Wood, composite wood, metal
Storefront Base (Bulkhead) Stucco, tile
Chimneys Chimneys
Cap Stucco, terra-cotta clay barrel tiles, copper, steel
Body Stucco, brick, stone, cast stone (including veneers of any of the above)
Exterior Building Lighting Exterior Building Lighting
Body and Mount Wrought iron, metal
Shield Clear, translucent, punched, louvers
Stairs and Ramps Stairs and Ramps
Treads and Risers Stucco, brick, stone, tile, concrete 25
Handrails Wood, composite wood, stucco, stone, wrought iron, metal
Trellises and Carports Trellises and Carports
Spanning Members Wood
Trellis Posts Wood
Carport Support Posts Wood, composite wood, stucco,
Connections Steel, iron
Trash Enclosure Trash Enclosure
Walls Wood, composite wood, stucco
Fences and Hedges Fences and Hedges
Walls Stucco, stone (faux manufactured stone veneer is prohibited)
Fences 26 Wood, composite wood, wrought iron, metal, chain link (vinylcoated black or green)
Stucco wall finish shall be smooth trowel, with 1/2" to 3/4" bull-nosed corners.
Accent tile shall be 6" x 6" minimum. Accent tile shall be 6" x 6" minimum.
Where used, "metal" and "wrought iron" shall be solid metal (not hollow tube).

Notes:

22 Applies to pitched roof forms; visible birdstops not allowed.
23 Required on façades facing streets and community open spaces.
24 Metal roll up doors are allowed only if not publicly visible. Metal security grilles (including roll up function) are allowed for parking structures.
25 Allowed on façades not facing streets and community open spaces.
26 Chain link fences are prohibited within the El Pueblo Viejo Landmark District. In other locations, publicly visible chain link fences are prohibited unless screened with vines.

(Ord. 6170, 2/25/2025)

Exceptions & meaning →

§ 25.06.060. Contemporary Style Group.

A. General Description.

  1. Contemporary Sub-Style. Contemporary style buildings have a sleek aesthetic and minimal ornamentation. This style focuses on combining simple rectilinear massing forms with changes in material and color. The use of glass and cantilevered elements imbues buildings with a sense of lightness and simplicity.

  2. Industrial Sub-Style. The Industrial style similarly uses simple building forms, but utilizes gabled roof forms as well as flat roofs. Openings are simple and laid out in a rational manner. Thoughtful aging of industrial material, often metal, is allowed.

B. Character Description.

  1. Contemporary.
Simple rectilinear massing volumes
Limited pushing and pulling of massing forms, delineated by changes in materials, colors, and finishes
Limited ornamentation and simple punched openings
Bay windows, awnings, balconies, and trellises used to break down façade and volume
  1. Industrial.
Low- and medium-pitched or flat roofs with shallow eave or parapet
Simple gable roof forms
Horizontally proportioned opening made from ganged vertical windows
Elements of Contemporary Style
Example Building Elevation: Contemporary

C. Wall.

  1. Contemporary.

Base

Base is not required for this sub-style.
Middle and Top Middle and Top
Cantilever without visually supportive column 6'-0" max. projection
Material changes may only occur at convex corners both vertical and horizontal.
Elements of Industrial Style
Example Building Elevation: Industrial
  1. Industrial.

Trim 1

Width 3" min. A
Base Base Base
Height 1'-0" min.; 1/2 story max. B
Required Articulation Change in finish material C
Base is required for this sub-style. Base is required for this sub-style. Base is required for this sub-style.
Middle and Top Middle and Top Middle and Top
Cantilever without visually supportive column 6'-0" max. projection 6'-0" max. projection
Material changes may only occur at convex corners both vertical and horizontal.

Note:

1 Trim not required on buildings or portions of buildings where stucco or stone is the primary wall material.

D. Building Roof: All.

Shed Roof Elevation
Building Roof Standards Sloped Roof Flat Roof Flat Roof
Roof Form Roof Form Roof Form Roof Form
Type Shed, Gable Flat
Pitch 2:12 min. 8:12 max. N/A D
Applicable Subsections Applicable Subsections Applicable Subsections Applicable Subsections
E. Rake Applies N/A
F. Eave Applies N/A
G. Parapet N/A Applies

E. Rake.

Flush Rake Section
Projecting Rake Section
  1. Contemporary.
Standards Flush Profile Projecting Profile Projecting Profile
Horizontal Projection No min.; 2'-6" min.;
Horizontal Projection 2" max. 6'-0" max. E
See Subsection F (Eave) for height standards.
  1. Industrial.
Standards Flush Profile Projecting Profile Projecting Profile
Horizontal Projection No min.; 6" min.;
2" max. 1'-6" max. E
See Subsection F (Eave) for height standards.

F. Eave: All.

Closed Eave Section
Open Eave Section
Standards Open Eave Closed Eave Closed Eave
Height Height Height Height
Fascia 6" min. 6" min. F
Horizontal Projection 2 Horizontal Projection 2 Horizontal Projection 2 Horizontal Projection 2
Overall 1'-6" min. N/A G

Note:

2 Horizontal projection includes gutter.

G. Parapet.

Parapet Section
  1. Contemporary.

Parapet Cap/Molding

Height 0" min.; 1'-0" max. H
Horizontal Projection 0" min.; 3" max. I
  1. Industrial.

Parapet Cap/Molding

Height 0" min.; 6" max. H
Horizontal Projection 0" min.; 3" max. I

H. Windows.

Typical Window Elevation: Contemporary Ganged Window Elevation: Contemporary
  1. Contemporary.

Opening Proportion, Height J to Width K Typical Window

Ground Floor 11:5 min. 11:5 min.
Typical Upper Floor 2:1 min. 2:1 min.
Accent Window Accent Window Accent Window
Rectangle 3:2 min. (2'-6" max. width) 3:2 min. (2'-6" max. width)
Square 1:1 min. (3'-0" max. width) 1:1 min. (3'-0" max. width)
Ganged Window 3:5 min. 3:5 min.
Picture Window 11:10 min. 11:10 min.
Dormer Window 2:1 min. 2:1 min.
Opening Opening Opening
Shape Rectangular Rectangular
Window Window Window
Operation Double-Hung, Single-Hung, Awning, Casement, Fixed Double-Hung, Single-Hung, Awning, Casement, Fixed
Glazing Divisions None required None required
Sash Widths Sash Widths Sash Widths
Rail 2" min. L
Stile 2" min. M
Trim Widths 3 Trim Widths 3 Trim Widths 3
Head 2" min. 2" min.
Jamb 2" min. 2" min.
Apron 2" min. 2" min.
Window Frame Recess Window Frame Recess Window Frame Recess
Depth 2" min. from face of sash 2" min. from face of sash
Sill Projection Sill Projection Sill Projection
Depth 2" min. from face of trim or surround 2" min. from face of trim or surround
Pediment Pediment Pediment
Allowed No No
Mullions Mullions Mullions
Mullions required between ganged windows.

Note:

3 Trim required for windows only on buildings or parts of buildings with lap siding.
Typical Window Elevation with 12 Parts Glazing Division: Industrial Ganged Window Elevation with 8 Parts and 12 Parts Glazing Divisions: Industrial
  1. Industrial.

Opening Proportion, Height N to Width O Typical Window

Ground Floor 11:5 min.
Typical Upper Floor 2:1 min.
Accent Window
Rectangle 3:2 min. (2'-6" max. width)
Square 1:1 min. (3'-0" max. width)
Ganged Window 3:5 min.
Picture Window 11:10 min.
Dormer Window 2:1 min.
Opening Opening Opening
Shape Rectangular
Window Window Window
Operation Double-Hung, Single-Hung, Awning, Casement, Fixed
Glazing Divisions 4 6 equal parts min.; 12 equal parts max.
Sash Widths
Rail 2" min. P
Stile 2" min. Q
Trim Widths 5
Head 2" min. R
Jamb 2" min. S
Apron None
Window Frame Recess Window Frame Recess Window Frame Recess
Depth 2" min. from face of sash
Sill Projection Sill Projection Sill Projection
Depth 2" min. from face of trim or surround
Pediment Pediment Pediment
Allowed No
Mullions Mullions Mullions
Mullions required between ganged windows.

Notes:

4 Glazing divisions for picture windows may be one part.
5 Trim required for windows only on buildings or parts of buildings with lap siding.

I. Bay Windows: All.

Bay Window Plan
Bay Window Elevation

Form

Type Square
Dimensions Dimensions Dimensions
Width 6'-0" min.; 12'-0" max. T
Depth 8" min.; 4'-0" max. U
Height Standards Height Standards Height Standards
Bay window may extend from second story to top story.
Bay window may occupy first story on buildings less than 3 stories tall.
Bay window form shall be vertically continuous from lowest bay window to highest bay window.
Allowed Cornice Treatments Allowed Cornice Treatments Allowed Cornice Treatments
Building parapet wraps bay window form. Building parapet wraps bay window form. Building parapet wraps bay window form.
Bay window stops below building eave (provide roof or cornice for bay window).
Bay window terminates into building eave (bay window form shall not project vertically or horizontally beyond building eave).

J. Dormers: All.

Dormer Elevation

Roof Form

Type Shed
Pitch 2:12 min.; 6:12 max.
Horizontal Projection Horizontal Projection
Rake See Subsection E (Rake) for rake standards.
Eave See Subsection F (Eave) for eave standards.
Placement Placement
Setback from Façade to Face of Dormer 1'-0" min.
Dormers shall not interrupt continuity of main building roof eave.
Window Window
See Subsection H (Windows) for window standards.

K. Entry Doors.

Vision Glass Door Elevation with Square Span Half Glass Door Elevation with Sidelights Full Glass Door Elevation with Transom
  1. Contemporary.

Door

Number of Panels 0 min.
Lite Types/Glazing Divisions Lite Types/Glazing Divisions
Vision Glass 0 min.
Half Glass 0 min.
Full Glass 0 min.
Surround Surround
Span Type Square
Glazed Openings Glazed Openings
Transom Allowed
Sidelights Allowed
  1. Industrial.

Door

Number of Panels 0 min.
Lite Types/Glazing Divisions Lite Types/Glazing Divisions Lite Types/Glazing Divisions
Vision Glass 0 parts min.; 4 parts max.
Half Glass 4 parts min.
Full Glass 8 parts min.
Surround Surround Surround
Span Type Square
Head Width 2" min. V
Jamb Width 2" min. W
Glazed Openings Glazed Openings Glazed Openings
Transom Allowed
Sidelights Allowed

L. Columns/Pilasters.

One-Story Porch: Contemporary
  1. Contemporary

Columns + Pilasters

Shape Square, Steel Section Square, Steel Section
Width/Diameter 6" min.; 4" min. for Steel Section 6" min.; 4" min. for Steel Section
Spacing 8'-0" max. on center X
Pedestal Height 6 3'-0" min. 3'-0" min.
Columns must not span multiple stories Columns must not span multiple stories Columns must not span multiple stories
Additional Features Additional Features Additional Features
Paneling Not Allowed Not Allowed
Fluting Not Allowed Not Allowed

Note:

6 Pedestal may be omitted.
One-Story Porch with Square Columns on Pedestals: Industrial
  1. Industrial.

Columns + Pilasters

Shape Square, Steel Section Square, Steel Section
Width/Diameter 6" min.; 4" min. for Steel Section 6" min.; 4" min. for Steel Section
Spacing 9'-6" min., 12'-0" max. on center Y
Pedestal Height 7 3'-0" min. Z
Columns must not span multiple stories. Columns must not span multiple stories. Columns must not span multiple stories.
Additional Features Additional Features Additional Features
Paneling Not Allowed
Fluting Not Allowed
Entablature Height Entablature Height Entablature Height
Topmost Floor 1'-6" min. A
Intermediate Floor 10" min.

Note:

7 Pedestal may be omitted.

M. Balconies: All.

Juliet Balcony with Horizontal Railing, Front Elevation Balcony with Mesh Railing, Front Elevation
Juliet Balcony with Horizontal Railing, Front Elevation Balcony with Horizontal Railing, Front Elevation
Juliet Balcony with Horizontal Railing, Front Elevation Balcony with Panel Railing, Front Elevation

Allowed Types Type 1 - Juliet Balcony

Inward-swinging door with full glazing required Inward-swinging door with full glazing required B
Base Height 3" min. C
Base Projection 4" min.; 2'-0" max. 4" min.; 2'-0" max.
Type 2 - Occupiable Balcony Type 2 - Occupiable Balcony Type 2 - Occupiable Balcony
Clear Depth 6'-0" min.
Cantilever without supporting columns 6'-0" max.
Area 48 sq. ft. min.
Recess into Façade 4'-6" max.
Overall Width 10'-0" max. D
Guard/Railing Guard/Railing Guard/Railing
Allowed Types Panel, Mesh, Horizontal Panel, Mesh, Horizontal
Height Per Building Code E
Width Between Posts 3'-0" min. on center F

N. Store fronts: All.

Store Section Storefront Elevation

Width

Storefront Module 10'-0" min.; 25'-0" max. G
Display Window 3'-0" min.; 6'-0" max. H
Glazing Divisions None required
Distance Between Storefront Modules 8 1'-0" min.; 4'-0" max. I
Height Height Height
Overall N/A
Head Height 10'-0" min. J
Cornice None
Signage Band None
Bulkhead 0" min.; 2'-0" max. K
Horizontal Recess Horizontal Recess Horizontal Recess
Depth 6" min.; 9" max. 9 L
Bulkhead shall be continuous, unless divided by pilaster.

Notes:

8 May be expressed with pilasters. See Subsection L (Columns/Pilasters)
9 No max. depth for residential entries.

O. Awning.

Awning Section Awning Elevation
  1. Contemporary.

Awning Design

Horizontal Projection 10 3'-0" min. M
Offset from Opening 1'-0" max. N
Required Support Elements Structural metal, tubing, or cable

Note:

10 Horizontal projection includes gutter, where occurs.

P. Trellises and Carports: All.

Trellis Diagram
Dimensions Wood Metal Metal
Post 8" x 8" min. 4" x 4" min. O
Main and Cross Beam 4" x 8" min. 11 2" x 4" min. P
Rafter 2" x 4" min. 1.5" x 3" min. Q
Purlin or Lattice 2" x 2" min. 1.5" x 1.5" min. R
Overhang Overhang Overhang S
Beams 3'-0" max. 3'-0" max.
Purlin or Lattice 2'-0" max. 2'-0" max.
Trellis 1'-6" max. 1'-6" max.
At balconies, overhangs may not project beyond balcony wall.

Note:

11 Paired 2" x 8" members are allowed when placed on both sides of the supporting posts.

Q. Materials.

  1. Contemporary.
Element Allowed Materials
Building Wall Building Wall
Cladding Lap siding (wood, composite wood, fiber cement), stucco, concrete, metal panel 12
Base or Foundation Base or Foundation
Base or Foundation Wood, composite wood, stucco, brick, stone, concrete, fiber cement
Roof and Roof Elements Roof and Roof Elements
Roofing 13 Shingles (composite wood, dimensional or luxury asphalt shingles to mimic the look of wood); standing seam metal (black, white, or reflective metal finishes are prohibited)
Rake and Eave Wood, composite wood, steel
Gutter Profile Box
Materials Metal
Windows, Bay Windows, and Entry Doors Windows, Bay Windows, and Entry Doors
Entry Door Wood, composite wood, metal, fiberglass
Window Frames Wood, composite wood, aluminum-clad wood steel
Glazing Clear glass; shall not be tinted, mirrored, or colored
Garages Garages
Garage Door 14 Wood, composite wood, metal, opaque glass
Balconies Balconies
Posts and Handrail Metal
Railing Metal panel, metal mesh, steel section, steel cable
Fascia Wood, composite wood, metal
Porches Porches
Columns Wood, composite wood, metal, fiberglass
Railing Wood, composite wood, metal panel, metal mesh, steel section, steel cable
Storefronts Storefronts
Storefront Base (Bulkhead) Wood, composite wood, concrete, metal panel, fiberglass
Exterior Building Lighting Exterior Building Lighting
Body and Mount Wrought iron, metal
Shield Clear, translucent, punched, louvers
Stairs and Ramps Stairs and Ramps
Treads and Risers Wood, composite wood, concrete, metal
Handrails Wood, composite wood, metal
Trellises and Carports Trellises and Carports
Spanning Members Wood, steel
Trellis Posts Wood, steel
Carport Support Posts Wood, composite wood, stucco, steel
Connections Steel, iron
Trash Enclosure Trash Enclosure
Walls Wood, composite wood, stucco
Fences and Hedges Fences and Hedges
Walls Stucco, brick, stone (faux manufactured stone veneer is prohibited), concrete, concrete block (coated and painted or pigmented to match the main building)
Fences 15 Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)
All ends of hollow steel members must be capped.

Notes:

12 Metal panel wall cladding is allowed only if used as an accent and not for the entire wall surface.
13 Applies to all pitched roofs and sloped roof parapets.
14 Metal roll up doors are allowed only if not publicly visible. Metal security grilles are allowed for parking structures.
15 Publicly visible fences may not be chain link unless screened with vines.
  1. Industrial.
Element Allowed Materials
Building Wall Building Wall
Cladding Lap siding (wood, composite wood, fiber cement), stucco, metal panel
Base or Foundation Base or Foundation
Base or Foundation Brick, concrete
Roof and Roof Elements Roof and Roof Elements
Roofing Shingles (composite wood, dimensional or luxury asphalt shingles to mimic the look of wood); standing seam metal (black, white, or reflective metal finishes are prohibited)
Rake and Eave Wood, composite wood, steel
Gutter Profile Half-round, box
Materials Metal
Windows, Bay Windows, and Entry Doors Windows, Bay Windows, and Entry Doors
Entry Door Wood, composite wood, metal, fiberglass
Window Frames Wood, aluminum-clad wood, steel
Glazing Clear glass; shall not be tinted, mirrored, or colored
Garages Garages
Garage Door 16 Wood, composite wood, metal, opaque glass
Balconies Balconies
Posts Metal
Railing Metal panel, metal mesh, steel section, steel cable
Handrail Wood, composite wood, metal
Fascia Wood, composite wood, metal
Porches
Columns Wood, composite wood, metal, fiberglass
Pedestal Wood, composite wood, concrete, metal, fiberglass
Railing Wood, composite wood, metal panel, metal mesh, steel section, steel cable
Storefronts Storefronts
Storefront Base (Bulkhead) Wood, composite wood, concrete, metal panel, fiberglass
Exterior Building Lighting Exterior Building Lighting
Body and Mount Wrought iron, metal
Shield Clear, translucent, punched, louvers
Stairs and Ramps Stairs and Ramps
Treads and Risers Metal, concrete
Handrails Metal
Trellises and Carports Trellises and Carports
Spanning Members Steel
Trellis Posts Steel
Carport Support Posts Steel
Connections Steel
Trash Enclosure Trash Enclosure
Walls Wood, composite wood, stucco
Fences and Hedges Fences and Hedges
Walls Stucco, brick, stone (faux manufactured stone veneer is prohibited), concrete, concrete block (coated and painted or pigmented to match the main building)
Fences 17 Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)
All ends of hollow steel members must be capped.

Notes:

16 Metal roll up doors are allowed only if not publicly visible. Metal security grilles (including roll up function) are allowed for parking structures.
17 Publicly visible fences may not be chain link unless screened with vines.

(Ord. 6170, 2/25/2025)

Exceptions & meaning →

Get a plain-English answer with a citation back to this text.

Ask AI about this code
Export this section
▸Contents — Santa Barbara Municipal Code
Santa Barbara Municipal Code

GoCodebook provides public access, search, citation, multilingual explanation, and practical interpretation of legally adopted building regulations. It is not a substitute for the official ICC or California code publications.