Chapter 17.85 — UTILITIES AND SERVICES
Palmdale Municipal Code · 2026-07 edition · updated 2026-09-27 · Palmdale
§ 17.85.010. Utilities, service areas, and building equipment.¶
(A) Undergrounding of Utilities.
(1) All new utility lines 50 kV and less, utility boxes, and utility equipment within a project and along adjacent regional and crosstown streets shall be placed underground pursuant to PMC Chapter 12.04 (Underground Utilities) unless otherwise prohibited by the utility provider (e.g., water backflow prevention device that must be placed above ground) or the City Engineer grants an exemption following his/her/their determination that such undergrounding is not practicable.
(2) Exception.
(a) In industrial zones, and for public/institutional development consistent with industrial zones, the Review Authority may reduce, waive, or defer requirements for utility line undergrounding and utility equipment screening, pursuant to PMC Chapter 12.04 (Underground Utilities) for portions of buildings not visible from regional and crosstown streets, and less intensive zones; and provided, that such action is determined to have no adverse effects. Additionally, for infill industrial projects in substantially developed industrial zones where utility lines have not been placed underground within the vicinity of the site, the City Engineer may defer utility line undergrounding requirements until such time as lines in the general area are undergrounded.
(b) In industrial zones, and for public/institutional development consistent with industrial zones, the requirement for undergrounding of utility lines may be waived for remodeling of existing structures where the cost of remodeling is less than 50 percent of the replacement cost of the existing structure as determined for building permits.
(B) Location of Service Areas, Storage, Utilities, and Equipment. All aboveground utilities and equipment (e.g., electric and gas meters, fire sprinkler valves, irrigation backflow prevention devices, etc.), service areas, and storage areas shall be integrated into building and landscape design and located to minimize impact on the pedestrian experience and neighboring properties by following the standards below:
(1) Utilities and equipment, service, storage, and nonpassenger loading areas shall be located inside of buildings or on nonprimary street frontages, alleys, parking areas, and/or at the rear or side of buildings and shall be fully screened from view per Subsection (C) of this Section (Service, Storage, Utility, and Equipment Screening).
(2) Utilities and equipment, service, storage, and nonpassenger loading areas shall not be located within setback areas, along midblock pedestrian connections, within the public right-of-way, and/or within 25 feet of a street corner.
(3) Except as otherwise required for fire safety as determined by the Director, roof ladders shall only be installed inside the associated building.
Downloaded from https://ecode360.com/PA4578 on 2026-07-07
City of Palmdale, CA § 17.85.010
ZONING
§ 17.85.010
==> picture [381 x 140] intentionally omitted <==
(C) Service, Storage, Utility, and Equipment Screening. All service and storage areas, utilities, and equipment not housed inside buildings shall meet the following screening standards:
(1) Screening shall be equal to or higher than the height of the equipment to be screened, unless specified otherwise.
(2) Screening shall be made of a primary exterior finish material used on other portions of the building, architectural grade wood or masonry, metal, or landscape screening that forms an opaque barrier when planted.
(3) Roll-up and service doors shall be painted to blend in with the main building colors and shall not face regional and crosstown streets. Where site constraints make the placement of these doors away from regional and crosstown streets infeasible, then doors shall be designed with glass or other architectural features to minimize visual impacts from the street, subject to approval by the Review Authority.
(4) Long-term shopping cart storage areas shall be completely screened. If screen walls are used, they shall be of sufficient height and length to screen all carts, and shall be made of a primary exterior finish material used on the main building, architectural grade wood or masonry, metal, or landscape screening that forms an opaque barrier when planted.
(5) All vents, flashing, electrical conduits, etc., shall be painted to match the color of the adjacent surface.
(6) The installation of gutters and downspouts on the exterior surface of new nonresidential buildings shall be prohibited.
(D) Location and Screening of Rooftop Equipment. Rooftop elements including roof access, mechanical equipment, and other features needed for the function of the building shall be located to minimize visual impact by meeting the following requirements. Mechanical equipment less than two feet in height, solar panels, wind generators, or green roof features shall be exempt from these requirements.
(1) Mechanical equipment shall be set back a minimum of 10 feet from the roof edge or screened with a parapet wall.
(2) Rooftop equipment shall be screened through the use of parapet walls, towers, or other architectural features such that it is not visible from any point at or below the
Downloaded from https://ecode360.com/PA4578 on 2026-07-07
City of Palmdale, CA § 17.85.010
PALMDALE CODE
§ 17.85.020
roof level of the subject building (see Subsection (C) of this Section (Service, Storage, Utility, and Equipment Screening)).
(3) If equipment will be visible from adjacent taller buildings or from higher grades, it shall be painted to match the rooftop in color and should be grouped together where practical.
(Ord. 1603 § 4 (Exh. I), 2023)
§ 17.85.020. Refuse and recycling.¶
(A) Applicability. Any project for which an application for a building permit is submitted after the effective date of this Title shall include adequate, accessible areas for collecting and loading trash, recyclable materials, organic waste, and other refuse as required per State law. These regulations apply to refuse and recycling areas not accessible to the public, and which are used exclusively by the tenants/owners of the development site. The provisions of this Section apply to all development except as follows.
- (1) Single-family or multifamily residential development projects that do not necessitate communal or shared refuse and recycling areas/containers. In such cases, no enclosure structure shall be required; however, individual trash, recycling, and green waste containers shall be stored in such a manner that containers are not visible or screened from public view from the front of the property. Containers may be placed in public view for purposes of collection.
(B) General Requirements.
- (1) Trash, recycling, and organic waste containers and collection areas shall be adequate in capacity, number, and distribution to accommodate all waste generation of the site. An area for the storage of refuse/recycling shall be provided with minimum clear dimensions pursuant to Figure 17.85.020-1 (Refuse and Recycling Area Layout and Minimum Dimensions) for all multifamily residential uses, and for all nonresidential uses with a gross floor area of less than 25,000 square feet. At minimum, one such area shall be required. For larger projects, additional space(s) may be required as determined by the local waste management service provider based on the type of use, the size of the refuse area proposed, and the frequency of refuse collection. Enclosure size and configuration may be determined during development review for users with specialized requirements. Where practical, enclosures shall be sized to contain transformer boxes or other utility equipment which also requires screening.
Downloaded from https://ecode360.com/PA4578 on 2026-07-07
City of Palmdale, CA
ZONING
§ 17.85.020
§ 17.85.020
Figure 17.85.020-1. Refuse and Recycling Area Layout and Minimum Dimensions
==> picture [247 x 153] intentionally omitted <==
(2) Adequate and accessible enclosures for the storage of trash and recyclable materials shall be provided. An alternative to a trash/recycling enclosure shall include the placement of a bin in a concrete or metal lined pit. The use, location, design, construction, and accessibility of enclosures shall conform to the requirements in this Title, and shall be reviewed and approved by the Review Authority.
(3) When a site is retrofitted or upgraded to comply with refuse and recycling standards, the location of any new enclosures shall be reviewed by the local disposal service and approved by the Director.
(4) Solid waste collection areas shall not be used for storage or other purposes.
(5) To the extent feasible, refuse and recycling areas should be located adjacent to each other/within the same enclosure.
(C) Location.
(1) Refuse and recycling collection and trash compactor areas shall be located inside of buildings or inside of enclosures located along alleys or in parking areas at the rear or side of buildings. Refuse collection areas shall be prohibited within any required front setback, street side setback, any required parking spaces, landscape areas, and open space areas.
(2) Enclosures shall be located a minimum of 10 feet from any structure, 25 feet from any public street, 15 feet from a private street, and in nonresidential areas, 20 feet from any residentially zoned property.
(3) The location of enclosures shall not conflict with circulation or parking conditions on site. A condition shall not be created where a parked vehicle will obstruct access to an enclosure nor where a disposal truck will obstruct parked vehicles.
(4) Refuse and recycling enclosures shall be located in order to be easily accessible to refuse collection trucks and to site users. In general, distance from a building entry to the trash enclosure should not exceed 150 feet.
(D) Access. The storage area for refuse and recyclable materials shall be accessible to pedestrians (both residents and/or employees) of the development site and to refuse and
Downloaded from https://ecode360.com/PA4578 on 2026-07-07
City of Palmdale, CA § 17.85.020
PALMDALE CODE
§ 17.85.020
recycling haulers. Vehicle access requirements shall be as follows:
(1) Driveways or travel aisles leading to exterior collection areas or enclosures shall be a minimum of 16 feet in width and paved pursuant to PMC § 17.87.090 (Parking design standards).
(2) Where driveways do not extend from street to street, a turnaround area for collection vehicles shall be provided. Minimum turning radius for collection vehicles shall be provided at 26/46 feet.
(3) Driveways or travel aisles shall provide unobstructed paved access for collection vehicles and provide a minimum of 15 feet vertical clearance. In loading areas, minimum overhead vertical clearance shall be 25 feet for loading operations.
(4) A concrete apron or pad, having a minimum size of 10 feet in width by 20 feet in length, shall be constructed in front of each exterior collection area or enclosure or trash compactor areas or at the point of pick-up by the collection vehicle. The purpose of this pad is to prevent damage to the surrounding asphalt paving. The pad shall have a level surface and shall be paved with concrete. The Director may waive the requirement for, and/or size of, the concrete apron or pad, provided the property owner can demonstrate that the existing asphalt located at the access and servicing areas of the refuse and recycling enclosure has withstood ongoing, regular use without appreciable degradation.
(E) Enclosures. Exterior collection areas shall be within an enclosure that meets the following standards:
- (1) Minimum Height. Enclosures shall be adequate in height to fully screen containers and materials, with a minimum height of six feet.
(2) Design and Materials. Refuse/recycling enclosures shall be constructed of a primary exterior finish material used on other portions of the building, masonry, or decorative block, and may be accented with metal.
(3) Pedestrian Access. For multifamily residential developments, a pedestrian access and separate access for primary collection shall be provided.
(4) Roofing. A solid roof treatment that is architecturally compatible with the primary buildings on site shall be provided and shall be designed in a manner to prevent windblown trash from leaving the enclosure.
(5) Bins. All refuse and recycling shall be stored in metal containers to prevent it from being blown outside its walled enclosure by the wind. Lids must always remain closed except when loading or unloading.
(6) Gates. Solid metal self-closing gates painted to match the enclosure shall be required. All gates shall be post mounted. Gates shall be maintained in working order and shall remain closed except when in use.
(7) Protection from Bins and Vehicles. Concrete curbs, decorative bollards, or wheel stops shall be installed or constructed inside the enclosure to prevent bins from damaging the enclosure. Concrete curbs or equivalent shall protect the exterior of enclosures from adjacent vehicle parking and travel ways.
Downloaded from https://ecode360.com/PA4578 on 2026-07-07
City of Palmdale, CA
ZONING
§ 17.85.020
§ 17.85.020
(8) Landscape Screening. Enclosures shall be screened with appropriate plant material wherever they are in view of the general public from the street, access drives, or less intensive zones. Plant material shall be in compliance with the City's approved planting list.
(F) Trash Compactors.
(1) Trash compactor areas shall be provided with a floor drain and hose bibb to facilitate washing of nonhazardous waste fluids from the area.
(2) The design of trash compactor areas shall prevent runoff of waste fluids into adjacent structures or onto adjacent properties.
(G) Signage.
(1) A sign clearly identifying all refuse and recycling collection and loading areas and the materials accepted therein shall be posted adjacent to all points of direct access to refuse and recycling areas.
(2) The facility and/or containers shall be clearly marked to identify the type of material to be deposited, operating instructions and hours, and the identity and phone number of the facility operator to call if a machine is inoperative, and shall display a notice stating that no material shall be left outside the refuse or recycling enclosure.
(3) Facilities shall meet the sign requirements of the zone as set forth in this Title, unless otherwise specified; directional signs may be installed in compliance with PMC Chapter 17.88 (Signs).
==> picture [267 x 197] intentionally omitted <==
- (H) Maintenance. Maintenance of each enclosure area and any bins and containers shall be the responsibility of the property owner. The property owner shall be responsible for keeping the area clean and free of litter, rodents, and insects. Enclosures that are damaged to the point of nonuse will result in a service interruption if the hauler cannot access the containers and shall be repaired or replaced within 60 calendar days following notification by the City.
Downloaded from https://ecode360.com/PA4578 on 2026-07-07
City of Palmdale, CA § 17.85.020
PALMDALE CODE
§ 17.85.020
(I) Health and Safety.
(1) Refuse and recycling areas for mixed-use developments shall meet the standards as set forth in PMC § 17.56.030 (Performance standards for mixed-use zones), and PMC Chapter 17.84 (Performance Standards). If the facility is located in or near an area designated or planned for residential use, special conditions for hours of operation, type of machinery used, lighting, and truck routes may be required, as determined by the Review Authority.
(2) The facility shall meet all applicable requirements of the Fire Department, Health Department, and Building and Safety.
(Ord. 1603 § 4 (Exh. I), 2023)
Downloaded from https://ecode360.com/PA4578 on 2026-07-07
City of Palmdale, CA
Get a plain-English answer with a citation back to this text.
Ask AI about this code▸Contents — Palmdale Municipal Code
- Article 0 — PREAMBLE
- Article 1 — MUNICIPAL AFFAIRS
- Article 2 — FORM OF GOVERNMENT
- Article 3 — FISCAL MATTERS
- Article 4 — REVENUE RETENTION
- Article 5 — LAND USE REGULATION
- Article 8 — AMENDMENT
- Article 9 — INTERPRETATION
- Title 1
- Title 2
- Chapter 2.40 — PALMDALE FEE RESOLUTION
- Chapter 2.27 — AVIATION AND AEROSPACE COMMISSION
- Chapter 2.48 — PALMDALE NEIGHBORHOOD PARTNERS
- Chapter 2.04 — CITY MANAGER[1 ]
- Chapter 2.06
- Chapter 2.08 — CITY COUNCIL
- Chapter 2.10 — CITY CLERK
- Chapter 2.12 — ASSESSOR AND TAX COLLECTOR
- Chapter 2.16 — BONDS
- Chapter 2.20 — REPEALED[2 ] (Repealed by Ord. 1102)
- Chapter 2.24 — COMMUNITY REDEVELOPMENT AGENCY[3 ]
- Chapter 2.25
- Chapter 2.26 — BUILDING REHABILITATION APPEALS BOARD
- Chapter 2.27 — AVIATION AND AEROSPACE COMMISSION
- Chapter 2.28 — CIVIL DEFENSE AND DISASTERS
- Chapter 2.32 — PUBLIC LIBRARY
- Chapter 2.40 — PALMDALE FEE RESOLUTION
- Chapter 2.42 — CLAIMS AGAINST THE CITY FOR MONEY OR DAMAGES
- Chapter 2.44 — SENIOR CITIZENS ADVISORY COMMISSION
- Chapter 2.46 — PLANNING COMMISSION
- Chapter 2.48 — PALMDALE NEIGHBORHOOD PARTNERS
- Chapter 2.50 — HIRING PRACTICES (Repealed by Ord. 1465)
- Chapter 2.52 — PALMDALE AIRPORT
- Chapter 2.55 — PALMDALE HUMAN RIGHTS ADVISORY COMMITTEE
- Chapter 2.60 — ELECTRONIC SIGNATURES
- Title 3
- Chapter 3.40 — TRAFFIC IMPACT FEE REQUIREMENTS
- Chapter 3.02
- Chapter 3.04 — BUDGET ADOPTION PROCEDURES
- Chapter 3.05 — AUDIT COMMITTEE
- Chapter 3.10 — CITY OF PALMDALE ECONOMIC OPPORTUNITIES PROGRAM
- Chapter 3.12 — CLAIMS AGAINST THE CITY[2 ]
- Chapter 3.14
- Chapter 3.16 — REAL PROPERTY TRANSFER TAX
- Chapter 3.20 — SALES AND USE TAX
- Chapter 3.21 — TRANSACTIONS AND USE TAX
- Article I
- Article II
- Article III
- Chapter 3.24 — TRANSIENT OCCUPANCY TAX
- Chapter 3.28 — PUBLICITY AND ADVERTISING FUND
- Chapter 3.32
- Chapter 3.33 — AIR QUALITY IMPROVEMENT TRUST FUND
- Chapter 3.34 — PARKLAND DEDICATION
- Chapter 3.36 — REDEVELOPMENT AGENCY FEE
- Chapter 3.38
- Chapter 3.40
- Chapter 3.42
- Chapter 3.43
- Chapter 3.44 — BUSINESS LICENSE TAX
- Chapter 3.45 — PUBLIC FACILITY DEVELOPMENT IMPACT FEE REQUIREM…
- Chapter 3.46
- Title 4
- Chapter 4.01 — MUNICIPAL ELECTION DATES
- Chapter 4.01 — MUNICIPAL ELECTION DATES
- Chapter 4.04 — FAIR CAMPAIGN PRACTICES
- Chapter 4.08 — ELECTION CAMPAIGNS VOLUNTARY EXPENDITURE CEILING
- Chapter 4.10 — ELECTORAL DISTRICT BOUNDARIES
- Chapter 4.11 — COUNCILMEMBER TERMS
- Chapter 4.12 — FILLING CITY COUNCIL VACANCIES
- Title 5
- Article I — Business Permits Generally
- Article II
- Chapter 5.05 — CANNABIS
- Chapter 5.10 — SYNTHETIC DRUGS
- Chapter 5.12
- Chapter 5.28
- Chapter 5.44
- Chapter 5.48
- Article I
- Article II — Franchises, Fees and Rates
- Article III
- Article IV — Exclusions
- Article V
- Article VI
- Article VII
- Article VIII
- Article IX
- Chapter 5.56 — PROHIBITION OF MANDATORY COVID‑19 VACCINATIONS …
- Title 6
- Chapter 6.04 — ANIMAL CONTROL
- Chapter 6.08 — RACING HOMING PIGEONS
- Title 8
- Chapter 8.08 — GENERAL HAZARDS
- Chapter 8.10 — PUBLIC NUISANCES AND ABATEMENT PROCEDURES
- Chapter 8.04
- Chapter 1 — ADMINISTRATIVE PROVISIONS
- Chapter 65 — SIGNS
- Chapter 66 — SPECIAL SAFETY PROVISIONS
- Chapter 67 — SECURITY PROVISIONS
- Chapter 98 — UNOCCUPIED BUILDINGS AND STRUCTURES
- Chapter 8.05 — SOLAR ENERGY SYSTEMS
- Chapter 8.06 — RECYCLING AND DIVERSION OF CONSTRUCTION AND DEM…
- Article I — General Provisions
- Article II — Definitions
- Article III — Oil Well Sumps, Sand and Gravel Pits and Similar…
- Article IV — Wells, Test Holes, Cesspools, Cisterns and Septic…
- Article V — Swimming Pools
- Article VI — Water Hazards
- Article VII — Boxes and Chests
- Article VIII — Hazardous Oil Machinery
- Chapter 8.10 — PUBLIC NUISANCES AND ABATEMENT PROCEDURES
- Chapter 8.16 — RESTAURANT EMPLOYEE OUTER GARMENTS
- Chapter 8.20 — ABANDONED, WRECKED, DISMANTLED OR INOPERATIVE V…
- Chapter 8.24 — PARK AND RECREATION AREAS
- Chapter 8.25 — AMBULANCE SERVICE
- Chapter 8.28
- Chapter 8.32 — SKATEBOARDS, ROLLER SKATES AND BICYCLES
- Chapter 8.34 — REGULATION OF SMOKING AT PUBLIC PLACES AND PLAC…
- Chapter 8.36 — REGULATION OF PROPERTY MAINTENANCE
- Chapter 8.38 — VACANT AND ABANDONED PROPERTY REGISTRATION
- Chapter 8.40 — COMPREHENSIVE RESIDENTIAL RENTAL UNIT INSPECTIO…
- Chapter 8.41 — EMERGENCY KEY ACCESS SYSTEM
- Chapter 8.44 — MAINTENANCE OF STREET TREES
- Chapter 8.46 — REGULATION OF FOOD FACILITIES
- Chapter 8.48 — REGULATION OF ILLEGAL DUMPING
- Title 9
- Chapter 9.12 — OFFENSES AGAINST PUBLIC DECENCY
- Chapter 9.18 — DISTURBING, EXCESSIVE, LOUD, OR OFFENSIVE NOISE
- Chapter 9.45 — TRESPASS ON PUBLIC PROPERTY
- Chapter 9.04
- Chapter 9.08 — OFFENSES AGAINST THE PERSON
- Chapter 9.10 — SEX OFFENDER RESIDENCY AND PRESENCE RESTRICTIONS
- Chapter 9.11 — PUBLIC URINATION AND DEFECATION
- Article I — Places of Amusement or Entertainment
- Article II — Liquor
- Article IV — Capping and Impersonation
- Article V — Lewdness and Disorderly Houses
- Article VI — Indecent Exposure
- Article VII — Topless Waitresses and Performers
- Article VIII — Public Nuisance
- Chapter 9.13
- Chapter 9.14
- Chapter 9.16 — OFFENSES AGAINST PUBLIC PEACE
- Chapter 9.18
- Chapter 9.20 — OFFENSES AGAINST PROPERTY
- Chapter 9.24 — LOITERING FOR DRUG ACTIVITIES
- Chapter 9.25 — TRUANCY
- Article I — Curfew
- Article II
- Article III
- Chapter 9.30 — GRAFFITI PREVENTION AND ABATEMENT
- Chapter 9.32 — WEAPONS
- Chapter 9.33 — EVICTIONS FOR UNLAWFUL DRUG ACTIVITY
- Chapter 9.36 — VIOLATION – PENALTY
- Chapter 9.40 — BURGLAR ALARM SYSTEMS
- Chapter 9.44 — TRESPASS ON PRIVATE PROPERTY
- Chapter 9.45 — TRESPASS ON PUBLIC PROPERTY
- Chapter 9.46
- Chapter 9.47
- Chapter 9.50 — FILMING POLICY
- Chapter 9.51
- Title 10
- Chapter 10.04 — VEHICLES AND TRAFFIC CODE[1 ]
- Chapter 15.101
- Chapter 15.102
- Chapter 15.103
- Chapter 15.104
- Chapter 15.105
- Chapter 15.106
- Chapter 15.107
- Chapter 15.110
- Chapter 15.130
- Chapter 10.06 — PARKING CITATION PROCESSING
- Chapter 10.08 — ELECTRIC VEHICLE PARKING AND CHARGING
- Chapter 10.09
- Title 12
- Article I — Undergrounding Districts
- Article II — New Construction
- Chapter 12.08 — HIGHWAY PERMITS
- Chapter 16.24
- Chapter 12.12 — PARADES[1 ]
- Chapter 12.16
- Chapter 12.20 — POLICY FOR DISPLAYING WRITTEN MATERIALS AT CIT…
- Chapter 12.24
- Chapter 12.28
- Chapter 12.30 — SHOPPING CARTS
- Chapter 12.32 — MAINTENANCE OF DRAINAGE FACILITIES
- Chapter 12.34 — COMMUNICATIONS AND UTILITIES
- Chapter 12.36
- Title 13
- Chapter 13.02 — DEFINITIONS AND GENERAL PROVISIONS
- Article II — General Provisions
- Chapter 13.05 — SEWER COLLECTION SERVICE CHARGES
- Article I
- Article II — Fees
- Article III — Design Standards
- Chapter 13.11 — INDUSTRIAL WASTE
- Article II — Fees and Deposits – Industrial Waste
- Article III — Discharge of Industrial Waste to Public Sewers
- Article IV — Other Methods of Disposal
- Article V
- Chapter 13.14 — SANITARY SEWER OVERFLOW PREVENTION PROVISIONS
- Title 14
- Chapter 14.04
- Chapter 14.05 — WATER EFFICIENT LANDSCAPE
- Title 15
- Chapter 15.30 — CALGREEN RECYCLING REQUIREMENTS
- Chapter 15.01
- Chapter 15.24
- Chapter 15.28 — FLOODPLAIN MANAGEMENT
- Chapter 15.30 — CALGREEN RECYCLING REQUIREMENTS
- Title 16
- Chapter 16.00 — GENERAL PROVISIONS
- Chapter 16.20 — RESPONSIBILITIES AND DESIGNATIONS
- Chapter 16.30 — REQUIRED MAPS
- Chapter 16.140 — CORRECTIONS AND AMENDMENTS OF MAPS
- Chapter 16.00 — GENERAL PROVISIONS
- Chapter 16.20 — RESPONSIBILITIES AND DESIGNATIONS
- Chapter 16.30 — REQUIRED MAPS
- Chapter 16.40 — GENERAL TENTATIVE MAP PROCEDURES
- Chapter 16.50
- Chapter 16.60
- Chapter 16.70 — FINAL AND PARCEL MAP PROCESSING
- Chapter 16.80
- Chapter 16.90 — COMMON INTEREST DEVELOPMENT CONVERSIONS
- Chapter 16.100 — VESTING TENTATIVE MAPS
- Chapter 16.110 — DEDICATIONS AND IMPROVEMENTS
- Chapter 16.130 — LOT MERGERS/UNMERGERS
- Chapter 16.140
- Chapter 16.150 — LOT LINE ADJUSTMENTS
- Chapter 16.160 — CERTIFICATE OF COMPLIANCE
- Chapter 16.165 — REIMBURSEMENT AGREEMENTS
- Chapter 16.170 — ENFORCEMENT
- Title 17
- Chapter 17.12 — INTERPRETATIONS
- Chapter 17.20 — GENERAL REVIEW PROCEDURES
- Division 2 — REVIEW PROCEDURES
- Division 3 — RESIDENTIAL ZONES
- Chapter 17.37 — SUPPLEMENTAL STANDARDS FOR SINGLE-FAMILY RESID…
- Chapter 17.38 — SUPPLEMENTAL STANDARDS FOR MULTIFAMILY RESIDEN…
- Chapter 17.48 — DEVELOPMENT REGULATIONS
- Division 5 — MIXED-USE ZONES
- Division 6 — INDUSTRIAL ZONES
- Division 7 — SPECIAL PURPOSE ZONES
- Division 8 — GENERAL DEVELOPMENT STANDARDS
- Chapter 17.82 — SETBACKS AND LOCATION OF BUILDINGS
- Chapter 17.83 — TRANSITION BETWEEN LAND USES AND ZONES
- Division 9 — SPECIAL REGULATIONS
- Division 10 — ENVIRONMENTAL MANAGEMENT
- Chapter 17.102 — SURFACE MINING AND RECLAMATION
- Chapter 17.10 — INTRODUCTORY PROVISIONS
- Chapter 17.11 — SCOPE
- Chapter 17.12 — INTERPRETATIONS
- Chapter 17.13 — DELEGATION OF AUTHORITY
- Chapter 17.14 — DESIGNATION OF ZONES AND DISTRICTS
- Chapter 17.15 — MAPS
- Chapter 17.16 — DEFINITIONS
- Chapter 17.17 — RULES OF MEASUREMENT
- Chapter 17.20 — GENERAL REVIEW PROCEDURES
- Chapter 17.21 — SITE PLAN REVIEW
- Chapter 17.22 — CONDITIONAL USE PERMITS
- Chapter 17.23 — VARIANCES AND MINOR EXCEPTIONS
- Chapter 17.24 — ZONING/LAND USE ADMINISTRATION
- Chapter 17.25 — AGREEMENTS
- Chapter 17.26 — ADMINISTRATIVE APPROVALS
- Chapter 17.27 — COMPREHENSIVE DEVELOPMENT PLANS
- Chapter 17.28 — NONCONFORMING USES, STRUCTURES AND PARCELS
- Chapter 17.30 — GENERAL PURPOSE AND INTENT
- Chapter 17.31 — RURAL SINGLE-FAMILY RESIDENTIAL ZONES
- Chapter 17.32 — SINGLE-FAMILY RESIDENTIAL ZONES
- Chapter 17.33 — RESIDENTIAL NEIGHBORHOOD ZONES
- Chapter 17.34 — MOBILE HOME (MH)
- Chapter 17.35 — LAND USE REGULATIONS
- Chapter 17.36 — DEVELOPMENT REGULATIONS
- Chapter 17.37 — SUPPLEMENTAL STANDARDS FOR SINGLE-FAMILY RESID…
- Chapter 17.38 — SUPPLEMENTAL STANDARDS FOR MULTIFAMILY RESIDEN…
- Chapter 17.39 — STANDARDS FOR TWO-UNIT DEVELOPMENTS AND URBAN …
- Chapter 17.40 — GENERAL PURPOSE AND INTENT
- Chapter 17.41 — NEIGHBORHOOD COMMERCIAL (NC)
- Chapter 17.42 — REGIONAL COMMERCIAL (RC)
- Chapter 17.43 — VISITOR COMMERCIAL (VC)
- Chapter 17.44 — MEDICAL FLEX (MEDFX)
- Chapter 17.45 — EDUCATIONAL FLEX (EDFX)
- Chapter 17.46 — OFFICE FLEX (OFX)
- Chapter 17.47 — LAND USE REGULATIONS
- Chapter 17.48 — DEVELOPMENT REGULATIONS
- Chapter 17.49 — SUPPLEMENTAL STANDARDS
- Chapter 17.50 — GENERAL PURPOSE AND INTENT
- Chapter 17.51 — MIXED-USE 1 (MU 1)
- Chapter 17.52 — MIXED-USE 2 (MU 2)
- Chapter 17.53 — MIXED-USE 3 (MU 3)
- Chapter 17.54 — LAND USE REGULATIONS
- Chapter 17.55 — DEVELOPMENT REGULATIONS
- Chapter 17.56 — SUPPLEMENTAL STANDARDS
- Chapter 17.60 — GENERAL PURPOSE AND INTENT
- Chapter 17.61 — LIGHT INDUSTRIAL (LI)
- Chapter 17.62 — HEAVY INDUSTRIAL (HI)
- Chapter 17.63 — AEROSPACE INDUSTRIAL (AI)
- Chapter 17.64 — MINERAL RESOURCE EXTRACTION (MRE)
- Chapter 17.65 — LAND USE REGULATIONS
- Chapter 17.66 — DEVELOPMENT REGULATIONS
- Chapter 17.67 — SUPPLEMENTAL STANDARDS
- Chapter 17.70 — GENERAL PURPOSE AND INTENT
- Chapter 17.71 — PUBLIC FACILITIES ZONES
- Chapter 17.72 — OPEN SPACE (OS)
- Chapter 17.73 — UTILITIES AND RIGHTS-OF-WAY (U-ROW)
- Chapter 17.74 — SPECIFIC PLAN (SP)
- Chapter 17.75 — LAND USE REGULATIONS
- Chapter 17.76 — DEVELOPMENT REGULATIONS
- Chapter 17.77 — SUPPLEMENTAL STANDARDS
- Chapter 17.80 — PURPOSE AND APPLICABILITY
- Chapter 17.81 — PARCEL REQUIREMENTS
- Chapter 17.82 — SETBACKS AND LOCATION OF BUILDINGS
- Chapter 17.83 — TRANSITION BETWEEN LAND USES AND ZONES
- Chapter 17.84 — PERFORMANCE STANDARDS
- Chapter 17.85 — UTILITIES AND SERVICES
- Chapter 17.86 — LANDSCAPING, LIGHTING, WALLS, AND FENCES
- Chapter 17.87 — OFF-STREET PARKING AND LOADING
- Chapter 17.88 — SIGNS
- Chapter 17.89 — ANIMAL KEEPING
- Chapter 17.90 — GENERAL PROVISIONS
- Chapter 17.91 — RESIDENTIAL USES
- Chapter 17.92 — COMMERCIAL USES
- Chapter 17.93 — INDUSTRIAL USES
- Chapter 17.94 — PUBLIC AND CIVIC FACILITIES
- Chapter 17.95 — COMMUNICATIONS AND UTILITIES
- Chapter 17.96 — HAZARDOUS MATERIALS FACILITIES
- Chapter 17.97 — RECYCLING FACILITIES
- Chapter 17.98 — OTHER USES
- Chapter 17.99 — RENEWABLE ENERGY
- Chapter 17.100 — HILLSIDE MANAGEMENT
- Chapter 17.101 — TRANSPORTATION DEMAND MANAGEMENT
- Chapter 17.102 — SURFACE MINING AND RECLAMATION
- Title 18
- Chapter 18.05
- Title OT
- § OT.10.010. Community Redevelopment Agency Ordinances
- § OT.10.020. Palmdale City Council Ordinances