Installation, certification and related referenced standards (12‑16 series)

Grounded in the retrieved California Referenced Standards Code — click a citation to read the verbatim passage:

• CRSC § 12-16 High relevance — show source text

  CALIFORNIA STANDARD FOR RESIDENTIAL EXCESS FLOW ACTUATED AUTOMATIC GAS SHUTOFF VALVES (SEE CCR TITLE 24, PART 5, CHAPTER 12) STANDARD 12-16-2

  DIVISION OF THE STATE ARCHITECT

  Authority: Sections 19200–19204, Health and Safety Code. Reference: Sections 19201.5 and 19202, Health and Safety Code.

  DIVISION 1—CONSTRUCTION

  SCOPE

  Sec. 12-16-201. The American Society for Testing and Materials (ASTM) F2138-12(2017) Standard Specification for Excess Flow Valves for Natural Gas Service, and the American National Standards Institute (ANSI) Z21.93-2017/CSA 6.30-2017 Excess Flow Valves for Natural and LP Gas with Pressure up to 5 psig, shall be the applicable standards used by the Division of the State Architect for certification of these devices.

  Sec. 12-16-201.1. Each installation of a customer-owned device that satisfies this standard shall be in accordance with the California Plumbing Code (CCR Title 24, Part 5).

  2025 CALIFORNIA REFERENCED STANDARDS CODE 103

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  104 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-31C RADIATION SHIELDING STANDARDS

  STANDARD 12-31C-1

  DEPARTMENT OF HEALTH SERVICES

  Authority: Sections 102, 208 and 25811.

  Reference: Sections 102, 208 and 436.5.

  ALL HEALING ARTS X-RAY INSTALLATIONS

  Sec. 12-31C-101. All radiation shielding barriers in rooms and enclosures housing radiation machines shall comply with the mandatory standards and appendices in Report No. 35, “Dental X-RAY Protection”; Report 49, “Structural Shielding Design and Evaluation for Medical use of X-rays and Gamma Rays of Energies up to 10 MeV”; and Report No. 51, “Radiation Protection Design Guidelines for 0.1-100 MeV Particle Accelerator Facilities.” Published by the National Council on Radiation Protection and Measurements, 7910 Woodmont Avenue, Bethesda, Maryland 20814.

  2025 CALIFORNIA REFERENCED STANDARDS CODE 105

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  106 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-71 AIR FILTERS

  STANDARD 12-71-1

  STATE FIRE MARSHAL

  DESCRIPTION OF TEST APPARATUS, METHOD AND CLASSIFICATION REQUIREMENTS FOR AIR FILTERS

  Sec. 12-71-100.

  (a) Test apparatus.

  1. The test duct, made of M.S. gage galvanized sheet metal reinforced with angle irons, is 21 inches square (13 548 mm [2] ) and 13 [1] / 2 feet (4114 mm) long.
• CRSC § 12-16 High relevance — show source text

  12-16-1 ENGINEERING REGULATIONS—QUALITY AND

  DESIGN OF THE MATERIALS OF CONSTRUCTION

  CALIFORNIA STANDARD FOR EARTHQUAKE-ACTUATED AUTOMATIC GAS SHUTOFF SYSTEMS (SEE CCR TITLE 24, PART 2, CHAPTERS 16 AND 16A, AND CCR TITLE 24, PART 5, CHAPTER 12) STANDARD 12-16-1

  DIVISION OF THE STATE ARCHITECT

  Authority: Sections 19180–19183, Health and Safety Code. Reference: Section 19182, Health and Safety Code.

  DIVISION 1—CONSTRUCTION

  SCOPE

  Sec. 12-16-101. The American Society of Civil Engineers (ASCE) requirements for “Earthquake-Actuated Automatic Gas Shutoff Devices,” ANSI/ASCE/SEI 25-16 (copyright 2016 by ASCE), shall be the applicable standard used by the Division of the State Architect for the certification of these devices.

  Sec. 12-16-101.1. Each installation of a customer-owned device that satisfies this standard shall be in accordance with the California Plumbing Code (CCR Title 24, Part 5).

  2025 CALIFORNIA REFERENCED STANDARDS CODE 101

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  102 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-16-2 ENGINEERING REGULATIONS—QUALITY AND

  DESIGN OF THE MATERIALS OF CONSTRUCTION

  CALIFORNIA STANDARD FOR RESIDENTIAL EXCESS FLOW ACTUATED AUTOMATIC GAS SHUTOFF VALVES (SEE CCR TITLE 24, PART 5, CHAPTER 12) STANDARD 12-16-2

  DIVISION OF THE STATE ARCHITECT

  Authority: Sections 19200–19204, Health and Safety Code. Reference: Sections 19201.5 and 19202, Health and Safety Code.

  DIVISION 1—CONSTRUCTION

  SCOPE

  Sec. 12-16-201. The American Society for Testing and Materials (ASTM) F2138-12(2017) Standard Specification for Excess Flow Valves for Natural Gas Service, and the American National Standards Institute (ANSI) Z21.93-2017/CSA 6.30-2017 Excess Flow Valves for Natural and LP Gas with Pressure up to 5 psig, shall be the applicable standards used by the Division of the State Architect for certification of these devices.

  Sec. 12-16-201.1. Each installation of a customer-owned device that satisfies this standard shall be in accordance with the California Plumbing Code (CCR Title 24, Part 5).

  2025 CALIFORNIA REFERENCED STANDARDS CODE 103

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  104 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-31C RADIATION SHIELDING STANDARDS

  STANDARD 12-31C-1

  DEPARTMENT OF HEALTH SERVICES

• CRSC § 1009.12 High relevance — show source text

  Emergency exit and panic hardware.
  |SFM|Part 9, Section 1009.12| |Chapter 12-11A,
  12-11B|Detectable warning products and directional
  surfaces|DSA|Part 2, Sections 1112A.9, 1116A.5, 11B-247,
  11B-406.5.12, 11B-705, 11B-810.5.2| |Chapter 12-12|Reserved||| |Chapter 12-13|Standards for insulating material|CA/SFM|Part 2.5, Section R302.10.1
  Part 6, Section 110.8
  Part 9, Section 720, Table 721.1(1)
  Part 11, Section A5.504.4.8| |Chapter 12-16-1|California standard for earthquake-actuated
  automatic gas shutoff systems|DSA|Part 2, Chapters 16 and 16A
  Part 5, Section 1211.8| |Chapter 12-16-2|California standard for residential excess flow
  actuated automatic gas shutoff valves|DSA|Part 5, Section 1209.1| |Chapter 12-31C|Radiation shielding|DPH|Part 2, Section 3102C| |Chapter 12-71|Air filters|SFM|Part 4, Sections 401.2, 509.2.3, 509.2.3.4
  Part 6, Section 120.1| |Chapter 12-72-1|Protective signaling systems.
  Standard test procedures.|SFM|| |Chapter 12-72-2|Protective signaling systems. Single-and
  multiple-station fire alarm devices
  mechanically operated type.|SFM|| |Chapter 12-72-3|Protective signaling systems. Smoke detectors,
  combustion products type.|SFM||

  2025 CALIFORNIA REFERENCED STANDARDS CODE ix

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  x 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-1 ADMINISTRATION

  RESERVED

  2025 CALIFORNIA REFERENCED STANDARDS CODE 1

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  2 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-3 RELEASING SYSTEMS FOR SECURITY BARS IN DWELLINGS

  (This standard includes provisions of Underwriters Laboratories Subject 2326, Appendix B, dated December 17, 1999, reprinted with their permission.)

  INTRODUCTION

  SECTION 12-3-1—SCOPE

  12-3-1.1 These requirements cover releasing systems for bars, grilles, mesh, glazing or other items intended to provide security at doors and windows required for emergency escape from dwelling units. When actuated by the occupant, the system allows the obstructions over the door or window to be moved so occupants can escape in the event of an emergency.

• CRSC § 3108.12.1 High relevance — show source text

  3108.12.1 Installation. Heating or cooking equipment, tanks, piping, hoses, fittings, valves, tubing and other related components shall be installed as specified in the International Fuel Gas Code and the California Mechanical Code, and shall be approved by the fire code official.

  3108.12.2 Venting. Gas, liquid and solid fuel-burning equipment designed to be vented shall be vented to the outside air as specified in the International Fuel Gas Code and the California Mechanical Code . Such vents shall be equipped with approved spark arresters where required. Where vents or flues are used, all portions of the tent or membrane structure shall be not less than 12 inches (305 mm) from the flue or vent.

  3108.12.3 Location. Cooking and heating equipment shall not be located within 10 feet (3048 mm) of exits or combustible materials.

  3108.13 Flammable and combustible liquids. The storage of flammable and combustible liquids and the use of flammable-liquidfueled equipment shall be in accordance with Sections 3108.13.1 through 3108.13.3.

  3108.13.1 Use. Flammable-liquid-fueled equipment shall not be used in tents or membrane structures.

  3108.13.2 Flammable and combustible liquid storage. Flammable and combustible liquids shall be stored outside in an approved manner not less than 50 feet (15 240 mm) from tents or membrane structures. Storage shall be in accordance with Chapter 57.

  [California Code of Regulations, Title 19, Division 1, §324.(a) and (b)] Flammable and Combustible Liquids.

  (a) Liquids having a flash point below 200°F shall not be stored in any tent nor less than 50 feet from any tent.

  (b) Flammable or combustible liquids shall be stored and dispensed in accordance with the provisions of the California Fire Code. The enforcing authority may permit limited quantities of flammable or combustible liquids required for display and normal merchandising.

  3108.13.3 Refueling. Refueling shall be performed in an approved location not less than 20 feet (6096 mm) from tents or membrane structures.

  3108.14 Display of motor vehicles. Liquid- and gas-fueled vehicles and equipment used for display within tents or membrane structures shall be in accordance with Sections 3108.14.1 through 3108.14.5.3.

  3108.14.1 Batteries. Batteries shall be disconnected except where the fire code official requires that the batteries remain connected to maintain safety features.

  3108.14.2 Fuel. Vehicles or equipment shall not be fueled or defueled within the tent or membrane structure.

  3108.14.2.1 Quantity limit. Fuel in the fuel tank shall not exceed one-quarter of the tank capacity or 5 gallons (19 L), whichever is less.

  3108.14.2.2 Inspection. Fuel systems shall be inspected for leaks.

  3108.14.2.3 Closure. Fuel tank openings shall be locked and sealed to prevent the escape of vapors.

  3108.14.3 Location. The location of vehicles or equipment shall not obstruct means of egress.

• CRSC § 64703-64705. High relevance — show source text

  This installed weight per square foot shall conform with the manufacturer’s installed design density per square foot at the manufacturer’s labeled R -value.

  (b) Water heater insulation kits. No water heater insulation kit shall be sold, on or after March 25, 1982, unless it has a thermal resistance of at least R-6 and is so identified.

  Each water heater insulation kit sold shall include instructions which are equivalent to the Department of Energy standard practice for the installation of insulation on gas-fired, oil-fired and electric resistance water heaters, 44 Fed. Reg. pages 64703-64705.

  Authority: Section 25922, Public Resources Code.

  Reference: Section 25922, Public Resources Code.

  HISTORY:

  1. Amendment filed 8-10-81; designated effective 9-22-81 (Register 81, No. 33).
  2. Editorial correction of subsection (a) filed 1-13-82 (Register 82, No. 2).

  INTERPRETATION

  Sec. 12-13-1565.

  The General Counsel of the Commission shall make a determination as to the application or interpretation of any provision of this article to any person requesting such a determination. Any such request shall be submitted in writing to the Commission. The Commission shall make written replies to such inquiries and shall widely publish interpretations that have broad application or interest.

  Authority: Section 25218 (e), Public Resources Code.

  Reference: Sections 25920 and 25922, Public Resources Code.

  HISTORY:

  1. Amendment filed 8-10-81; designated effective 9-22-81 (Register 81, No. 33).

  100 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-16-1 ENGINEERING REGULATIONS—QUALITY AND

  DESIGN OF THE MATERIALS OF CONSTRUCTION

  CALIFORNIA STANDARD FOR EARTHQUAKE-ACTUATED AUTOMATIC GAS SHUTOFF SYSTEMS (SEE CCR TITLE 24, PART 2, CHAPTERS 16 AND 16A, AND CCR TITLE 24, PART 5, CHAPTER 12) STANDARD 12-16-1

  DIVISION OF THE STATE ARCHITECT

  Authority: Sections 19180–19183, Health and Safety Code. Reference: Section 19182, Health and Safety Code.

  DIVISION 1—CONSTRUCTION

  SCOPE

  Sec. 12-16-101. The American Society of Civil Engineers (ASCE) requirements for “Earthquake-Actuated Automatic Gas Shutoff Devices,” ANSI/ASCE/SEI 25-16 (copyright 2016 by ASCE), shall be the applicable standard used by the Division of the State Architect for the certification of these devices.

  Sec. 12-16-101.1. Each installation of a customer-owned device that satisfies this standard shall be in accordance with the California Plumbing Code (CCR Title 24, Part 5).

  2025 CALIFORNIA REFERENCED STANDARDS CODE 101

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  102 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-16-2 ENGINEERING REGULATIONS—QUALITY AND

• CRSC § 12-11 High relevance — show source text

  DETECTABLE WARNING PRODUCTS

  Sections 12-11A.203 and 12-11B.203. Must comply with the California Code of Regulations, Title 24.

  DIRECTIONAL SURFACES

  Sections 12-11A.204 and 12-11B.204. Must comply with the California Code of Regulations, Title 24.

  INDEPENDENT ENTITY

  Sections 12-11A.205 and 12-11B.205. Evaluation by an independent entity to confirm the prescriptive and performance standard of detectable warning products or direction surfaces installed after January 1, 2001. An independent entity is a not-for-profit product safety testing and certification organization, dedicated to testing for public safety. An independent entity would operate for the testing, certification and quality assessment of products, systems and services.

  TWO-YEAR APPROVAL

  Sections 12-11A.206 and 12-11B.206. Detectable warning products and directional surfaces are to be recertified every two years without exception or waiver.

  FEE

  Sections 12-11A.207 and 12-11B.207. The Division of the State Architect-Access Compliance may impose a fee on manufacturers of the specified products, to cover the cost of detectable warning products and directional surfaces.

  DISABILITY ACCESS ACCOUNT

  Sections 12-11A.208 and 12-11B.208. The fees received from manufacturers will be placed in the Disability Access Account.

  DETECTABLE WARNING PRODUCTS AND DIRECTIONAL SURFACES

  Sections 12-11A.209 and 12-11B.209. Detectable Warning Products and Directional Surfaces must ensure consistency and uniformity: (a) Shape, (b) Color fastness,

  (c) Conformation, (d) Sound-on-cane acoustic quality, (e) Resilience, and (f) Attachment will not degrade significantly for at least five years.

  SIGNIFICANT DEGRADATION

  Sections 12-11A.210 and 12-11B.210. Significant degradation means that the product maintains at least 90 percent of its approved design characteristics.

  SELECTION OF INDEPENDENT ENTITY

  Sections 12-11A.211 and 12-11B.211. The independent entity selected by the Division of the State Architect-Access Compliance shall be recognized as having appropriate expertise in determining whether products comply with the California Code of Regulations, Title 24.

  Authority: Government Code Sections 4450, 4460 and Health & Safety Code Section 18949.1.

  Reference: Government Code Section 4460.

  2025 CALIFORNIA REFERENCED STANDARDS CODE 85

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  86 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  2025 CALIFORNIA REFERENCED STANDARDS CODE 87

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  88 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-13 STANDARDS FOR INSULATING MATERIAL

  (See Part 6, Title 24, CCR)

  DEPARTMENT OF CONSUMER AFFAIRS

  Bureau of Household Goods and Services

• CRSC § 12-72 Medium relevance — show source text

  |SFM|| |Chapter 12-72-2|Protective signaling systems. Single-and
  multiple-station fire alarm devices
  mechanically operated type.|SFM|| |Chapter 12-72-3|Protective signaling systems. Smoke detectors,
  combustion products type.|SFM||

  2025 CALIFORNIA REFERENCED STANDARDS CODE ix

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  x 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-1 ADMINISTRATION

  RESERVED

  2025 CALIFORNIA REFERENCED STANDARDS CODE 1

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  2 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-3 RELEASING SYSTEMS FOR SECURITY BARS IN DWELLINGS

  (This standard includes provisions of Underwriters Laboratories Subject 2326, Appendix B, dated December 17, 1999, reprinted with their permission.)

  INTRODUCTION

  SECTION 12-3-1—SCOPE

  12-3-1.1 These requirements cover releasing systems for bars, grilles, mesh, glazing or other items intended to provide security at doors and windows required for emergency escape from dwelling units. When actuated by the occupant, the system allows the obstructions over the door or window to be moved so occupants can escape in the event of an emergency.

  12-3-1.2 These requirements only cover the ability of the releasing system to be manually activated from the interior of a dwelling unit by an occupant to affect an escape through the protected opening.

  12-3-1.3 These requirements cover releasing systems intended for use on the interior side of doors or windows in all climatic locations.

  12-3-1.4 These requirements do not evaluate the ability of the releasing system or obstructions to resist an external forced entry attack.

  12-3-1.5 These requirements do not evaluate the ability of the releasing system or obstructions to be opened or removed from the exterior of the residential dwelling unit by emergency response personnel during rescue operations.

  12-3-1.6 Products covered by these requirements are intended for installation in dwelling units to protect door and window openings that are designated by the California Building Standards Code to be used as the secondary means of escape from the living area.

  12-3-1.7 Products covered by these requirements are not intended to be used to protect doors in means of egress path for nonresidential occupancies, the common egress path of multifamily residential dwelling units or the primary means of egress path in a single-family dwelling unit.

  12-3-1.8 These requirements do not cover window guards or fall prevention devices that are intended to prevent falls from upper story windows.

  12-3-1.9 These requirements do not apply to storm doors and windows or light duty screens used for insect control.

• CRSC § 8-10 Medium relevance — show source text

  (b) Up to and including September 30, 1982, laboratories shall be approved either upon accreditation by the United States Department of Commerce National Voluntary Laboratory Accreditation Program or as stated in the preceding paragraph, at the manufacturer’s option. After September 30, 1982, laboratories shall only be approved upon accreditation by the United States Department of Commerce National Voluntary Laboratory Accreditation Program.

  Authority: Section 25218(e), Public Resources Code.

  Reference: Sections 25915(a) and 25921, Public Resources Code.

  HISTORY:

  1. Amendment filed 8-10-81, designated effective 9-22-81 (Register 81, No. 33).

  CERTIFICATION

  Sec. 12-13-1555.

  (a) No insulating material shall be sold or installed in California on or after September 22, 1981, unless the manufacturer has certified that the material complies with the provisions of this article.

  (b) The manufacturer shall submit a certification statement to the Executive Director for each type of insulating material. Such statement shall contain the following information:

  1. Name of the manufacturer.

  2. A description of the type of insulating material being certified in sufficient detail to permit its identification. The description may include information sheets, brochures, a sample label for the product or similar information.

  3. Test results from an approved laboratory.

  4. A description of the basis for ensuring that all the insulating material of the type being certified complies with the requirements of this article. Such description shall include, but not be limited to a description of the frequency of testing of the material, the quality assurance program, and any third-party inspections or testing used by the manufacturer.

  5. A declaration that the insulating material complies with the requirements of this article.

  6. The wording of the certification seal, if such seal consists of a statement pursuant to Section 1557 (b) (2) of this article.

  (c) Every certification statement shall be dated and signed by the manufacturer attesting to its truth and accuracy. Where the manufacturer is either a corporation or a business association, the certification statement shall be dated, signed and attested to by a responsible official thereof.

  (d) Within 45 days after receipt of a certification statement, the Executive Director shall forward, to the manufacturer, an acknowledgment that the statement has been received and that it is complete and accurate on its face.

  (e) Certification of the insulation material shall be deemed to occur upon forwarding of the acknowledgement by the Executive Director. If acknowledgment is not forwarded in a timely manner, certification shall be deemed to occur on the 45th day after receipt of the certification statement.

  (f) The statement of test results required in the certification may be based upon tests conducted prior to the adoptive date of this article if: (1) the same test was conducted within two years of the date of adoption, (2) the laboratory at which the tests were

  98 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  STANDARDS FOR INSULATING MATERIAL

  conducted has been approved for those tests as of the date of the certification statement, and (3) the laboratory certifies that the test and product are the same as the test and product referred to in the statement of test results.

  Authority: Section 25218(e), Public Resources Code.

  Reference: Sections 25921 and 25921.1, Public Resources Code.

  HISTORY:

• CRSC § 25.4 Medium relevance — show source text

  
  (MIN)**| |ITEM CODE|THICKNESS|CONSTRUCTION DETAILS|LOAD|PRE-BMS-92|BMS-92|POST-BMS-92|POST-BMS-92|POST-BMS-92| |FR-I-12|1/2″|1/2″ thick 1:2; 1:3 gypsum plaster on wood
  lath.|15 minutes||1||1–3|15| |FR-I-13|7/8″|1/2″ thick 1:2; 1:2 gypsum plaster on3/8″
  perforated gypsum lath.|30 minutes||1||1–3|30| |FR-I-14|7/8″|1/2″ thick 1:2; 1:2 gypsum plaster on3/8″
  thick plain or indented gypsum plaster.|20 minutes||1||1–3|20| |FR-I-15|3/8″|3/8″ gypsum wallboard.|10 minutes||1||1, 2|10| |FR-I-16|1/2″|1/2″ gypsum wallboard.|15 minutes||1||1, 2|15|

  For SI: 1 inch = 25.4 mm, °C = [(°F) - 32]/1.8.

  Notes:

  1. The finish rating is the time required to obtain an average temperature rise of 250°F, or a single point rise of 325°F, at the interface between the material being rated and the substrate being protected.
  2. Tested in accordance with the Standard Specifications for Fire Tests of Building Construction and Materials, ASA No. A2-1932.
  3. Mix proportions for plasters as follows: first ratio, dry weight of plaster to dry weight of sand for scratch coat; second ratio, plaster to sand for brown coat.
  4. Neat plaster means unsanded wood-fiber gypsum plaster.

  TABLE 1.5.2 FINISH RATINGS—ORGANIC MATERIALS	Col2	Col3	Col4	Col5	Col6	Col7	Col8	Col9
  ITEM CODE	THICKNESS	CONSTRUCTION DETAILS	PERFORMANCE	REFERENCE NUMBER	REFERENCE NUMBER	REFERENCE NUMBER	NOTES	REC. F.R. (min)
  ITEM CODE	THICKNESS	CONSTRUCTION DETAILS	FINISH RATING	PRE-BMS-92	BMS-92	POST-BMS-92	POST-BMS-92	POST-BMS-92
  FR-O-1	9/16″	7/16″ wood fiberboard faced with1/8″ cement-asbestos board.	15 minutes		1		1, 2	15
  FR-O-2	29/32″	3/4″ wood sheathing, asbestos felt weighing 14 lbs/100 ft2 and5/32″ cement-asbestos shingles.	20 minutes		1		1, 2	20
  FR-O-3	11/2″	1″ thick magnesium oxysulfate wood fiber- board faced with 1:3; 1:3 gypsum plaster,1/2″ thick.

• CRSC § 9.5 Medium relevance — show source text

  2. The specimen shall be suspended vertically with its lower edge 2 inches (51 mm) above the top of a [3] / 8 inch (9.5 mm) diameter Bunsen Burner. The test shall be performed in a draft-free area.

  3. The flames from the burner shall be 4 inches (101 mm) long and shall be adjusted with sufficient air supply to eliminate any yellow flame tips but without any distinct inner blue cone.

  4. The specimen shall be exposed to the flame at each corner and at not less than one other point along the lower edge. Each exposure shall be of sufficient duration to determine if the material will ignite and continue to burn, but shall be not less than 20 seconds.

  5. The criteria for acceptance shall be as follows: (A) There shall be not more than intermittent flaming appreciably beyond the area exposed to the test flame. (B) Flame shall not reach the top of the specimen. (C) On removing the test flame there shall be not more than 1 second of after flaming except there may be nonprogressive flaming of short duration in areas of accumulated char which were directly exposed to the test flame.

  Section 12-7-502

  (a) Framed rigid combustible decorative material. Rigid combustible decorative material and assemblies of materials not more than [1] / 4 inch (6 mm) in thickness used for folding doors, room dividers, decorative screens and similar applications, and which are installed with all edges protected, shall conform to the following:

  1. All exposed edges shall be protected with frames of metal or other noncombustible material, or solid wood of minimum [1] / 4 inch (6 mm) dimension.

  2. The total square foot area of the material shall not exceed ten percent of that of the floor area of the room in which the material is installed.

  3. When tested as follows, flames shall not reach the top edge of the specimen. The test shall be conducted in a draft free area, on a specimen of the material 12 inches by 12 inches (305 mm by 305 mm) suspended at a 45-degree angle from the horizontal with the upper and lower edges in a horizontal plane. The test flame shall be 3 inches (76 mm) long from a Bunsen burner of approximately [1] / 2 -inch (13 mm) inside diameter with the air supply completely shut off. The burner shall be positioned so that its top is 1 inch (25 mm) vertically below a point on the lower surface of the test specimen, 1 inch (25 mm) up from its lower horizontal edge and midway between the inclined edges. The exposure to the test flame and the duration of test shall be for a period of 2 minutes.

  2025 CALIFORNIA REFERENCED STANDARDS CODE 35

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  36 2025 CALIFORNIA REFERENCED STANDARDS CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  12-7A MATERIALS AND CONSTRUCTION METHODS

  FOR EXTERIOR WILDFIRE EXPOSURE

  EXTERIOR WALL SIDING AND SHEATHING

  SFM STANDARD 12-7A-1

  12-7A-1.1 Application. The minimum design, construction and performance standards set forth herein for exterior wall siding and sheathing are those deemed necessary to establish conformance to the provisions of these regulations. Materials and assemblies that meet the performance criteria of this standard are acceptable for use as defined in California Building Standards Code.

• CRSC § 603.4.2 Medium relevance — show source text

  2, 603.4.2| |ASSE/IAPMO/ANSI 6010-
  2021|Medical Gas Systems Installers|Certification|1323.10|

  2025 CALIFORNIA PLUMBING CODE 347

  ), Copyright © 2025 IAPMO, and may not be used for any other purpose or distributed to any other persons or parties.

  REFERENCED STANDARDS

  TABLE 1701.1 (continued) REFERENCED STANDARDS

  STANDARD NUMBER	STANDARD TITLE	APPLICATION	REFERENCED SECTION
  ASSE/IAPMO/ANSI 6020- 2021	Medical Gas Systems Inspectors	Miscellaneous	1324.5.4.7, 1324.5.6.2, 1324.5.6.5
  ASSE/IAPMO/ANSI 6030- 2021	Medical Gas Systems Verifiers	Miscellaneous	1324.5.4.7, 1324.5.6.2, 1324.5.6.5, 1324.5.7.2
  ASSE/IAPMO/ANSI 6035- 2021	Bulk Medical Gas/Cryogenic Fluid Central Supply Systems Verifiers	Miscellaneous	1324.5.7.3
  ASSE/IAPMO/ANSI Series 7000-2020	Residential Potable Water Fire Sprinkler System Installers & Inspectors for One- and Two-Family Dwellings	Miscellaneous	612.1
  ASSE/IAPMO/ANSI 12010-2021	Environment of Care, Infection Control and Construction Risk Assessment Professional Qualification Standard	Professional Qualifications	1303.9
  IAPMO IGC 78-2019	Drain, Waste and Vent (DWV) Internal Cleanout Fittings	DWV Components	Table 707.2
  IAPMO IGC 109-2019	Water Distribution Manifolds	Valves	606.5.1
  IAPMO IGC 127-2018	Combined Hand-Washing Systems	Fixtures	407.1, 420.1
  IAPMO IGC 154-2019	Shower and Tub/Shower Enclosures, Bathtubs with Glass Pres- sure-Sealed Doors, and Shower/Steam Panels	Fixtures	408.1
  IAPMO IGC 167-2011ae2 (R2021)	Solid Waste Containment Interceptors	Interceptors	Table 1009.1
  IAPMO IGC 183-2016	Oil/Water Separators and Coalescing Plate Separators	DWV Components	Table 1009.1, 1017.2
  IAPMO IGC 196-2018	Condensate Traps and Overflow Switches for Air-Conditioning Systems	Condensate Traps	814.4
  IAPMO IGC 224-2018	ABS, PVC and Cast Iron DWV Test Fitting with Integral Cleanout	DWV Components	Table 707.2
  IAPMO IGC 305-2019	ABS and PVC Horizontal Backwater Valves with Lifting Devices	Valves	710.6
  IAPMO IGC 322-2018	Alkaline Water – Drinking Water Treatment Units	Miscellaneous	611.1.

• CRSC § 12-8 Medium relevance — show source text

  12-8-100: Room Fire Tests for Wall and Ceiling Materials

  NA

  12-10-1: Power Operated Exit Doors

  NA

  12-10-2: Single Point Latching or Locking Devices

  NA

  12-10-3: Emergency Exit and Panic Hardware

  NA

  (The Office of the State Fire Marshal standards referred to above are found in the California Code of Regulations, Title 24, Part 12.):

  SJI Steel Joist Institute, 140 Evans Street, Suite 203, Florence, SC 29501

  SJI 100—2020: Standard Specification for K-Series, LH-Series, and DLH-Series Open Web Steel Joists and for Joist Girders

  1604.3.3, 2207.1, 2207.2, 2207.3, 2207.4, 2207.5

  SJI 200—2015: Standard Specification for CJ-Series Composite Steel Joists

  1604.3.3, 2207.1, 2207.2, 2207.3, 2207.4, 2207.5

  SPRI Single-Ply Roofing Industry, 465 Waverly Oaks Road, Suite 421, Waltham, MA 02452

  ANSI/SPRI GT-1—2022: Test Standard for External Gutter Systems

  1504.6.1, 1511.7.6.1

  ANSI/SPRI RP-4—2019: Wind Design Standard for Ballasted Single-ply Roofing Systems

  1504.5

  ANSI/SPRI VF-1—2021: External Fire Design Standard for Vegetative Roofs

  1505.10

  ANSI/SPRI/FM 4435/ES-1—2017: Test Standard for Edge Systems Used with Low Slope Roofing Systems

  1504.6, 1511.7.6.1

  35-40 2025 CALIFORNIA BUILDING CODE

  on Jul 18, 2025 11:14 AM (CDT) THEREUNDER.

  REFERENCED STANDARDS

  SRCC Solar Rating & Certification Corporation, 400 High Point Drive, Suite 400, Cocoa, FL 32926

  ICC 900/SRCC 300—2020: Solar Thermal System Standard

  3111.2.1

  ICC 901/SRCC 100—2020: Solar Thermal Collector Standard

  3111.2.1

  TIA Telecommunications Industry Association, 1320 N. Courthouse Road #200, Arlington, VA 22201

  ANSI/TIA 222-I—2023: Structural Standard for Antenna Supporting Structures, Antennas and Small Wind Turbine Support

  Structures

  1609.1.1, 3108.1, 3108.2

  TMS The Masonry Society, 105 South Sunset Street, Suite Q, Longmont, CO 80501-6172

  216—2014(19): Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies Table 721.1(2), 722.1

  302—2018: Standard Method for Determining the Sound Transmission Ratings for Masonry Assemblies

  1208.2.1

  402—16: Building Code Requirements for Masonry Structures

  2109.1, 2109.1.1, 2109.2