Santa Barbara County Municipal Code § 21-20 Streets and highways

(a) In the subdivision of land lying wholly or partly within the unincorporated territory of the county, the following regulations shall apply, and no tentative or final subdivision map shall be approved by the advisory agency until and unless such map or maps indicate a full compliance with the requirements of this division.

(b) This division shall also apply to the following for the sole purpose of implementing section 21-32A, Agricultural Buffers, of this division:

(1) Applications for conditional certificates of compliance which are regulated in compliance with division 13, Certificates of Compliance and Conditional Certificates of Compliance, of article I, Subdivisions, of this chapter.

(2) Applications for lot line adjustments which are regulated in compliance with article III, Lot Line Adjustments, of this chapter.

(3) Applications for modifications to conditional certificates of compliance, recorded maps, lot split plats and lot line adjustments which are processed in compliance with division 3, Modifications to Recorded Maps, Lot Split Plats and Lot Line Adjustments.

(Ord. No. 1722, pt. 5; Ord. No. 4854, § 3, 4-16-2013)

No tentative or final subdivision map shall be approved by the advisory agency unless it finds that the subject property is in compliance with all laws, rules and regulations pertaining to zoning uses, subdivisions, height and setbacks, and any other provisions applicable to the property for which the map is sought, and such zoning violation enforcement fees as established from time to time by the board of supervisors have been paid. This section shall not be interpreted to impose new requirements on legal nonconforming uses and structures.

(Ord. No. 3610, § 1)

(a) Block Lengths. Blocks shall not exceed one thousand five hundred feet between street lines except where topographic conditions require longer blocks.

(b) Block Widths. Blocks should be of sufficient width to permit the planting of two tiers of normal depth. No block shall be less than two hundred feet wide.

(Ord. No. 1722, pt. 5, § 1)

(a) Relation to General Plan. The street and highway arrangement of every subdivision shall not conflict with the circulation element of the county's comprehensive plan with respect to the placement of such streets, highways, or ways as may be shown thereon.

(b) Relation to Topography. Topographic conditions shall determine the general pattern of blocks, and natural contours shall control the placement and alignment of streets, highways, and ways.

(c) Relation to Adjoining and Adjacent Street System. Streets may be required to be laid out so as to directly continue the center lines of the principal existing streets or highways in adjacent or adjoining subdivided areas. In general, such streets shall have a width at least as great as the existing streets.

(d) Waterfront Streets. In the subdivision of land abutting the Pacific Ocean or tidewater thereof, where conditions warrant, a street, walk, or roadway may be required parallel to the line of mean high tide, and no private development shall be permitted between such street, walk, or roadway and the Pacific Ocean.

(e) Street Names. The names of new streets shall be subject to the approval of the decision-maker after review by the county surveyor and shall not duplicate existing street names where confusion is likely to result.

(f) Dead-end Streets. Where necessary to give access to or permit a satisfactory subdivision of adjoining land, streets shall run through to the boundary of the property and the resulting dead-end streets may be approved without a turn-around.

(g) Road Standards. In addition to the foregoing, road standards and principles shall be as prescribed by resolution of the board of supervisors. In cases where the director of public works deems that circumstances warrant, minor deviations may be permitted from any of the foregoing requirements or any other requirements adopted by the board of supervisors pursuant to the terms of this division relating to roads, road standards and specifications.

(Ord. No. 1722, pt. 5, § 2: Ord. No. 4436, § 19)

Narrow parcels or reserve strips controlling access to streets or highways from adjoining property will not be approved unless the control or disposal of such land is placed under the jurisdiction of the board of supervisors under conditions satisfactory to the board and the advisory agency.

(Ord. No. 1722, pt. 5, § 3)

The advisory agency may require that alleys be provided at the rear of commercial or multiple family parcels.

(Ord. No. 1722, pt. 5, § 4)

Easements for public utility purposes shall be provided at the location and of a width approved by the serving utilities and the advisory agency.

Rights-of-way as required by the advisory agency for access shall be provided along all natural watercourses where access is necessary for flood control maintenance and improvement and for other public purposes. Depending on topography, such rights-of-way shall be required to include the natural channel plus a strip of land twenty feet wide on the flat land along the edge of channels which do not exceed twenty-five feet in width. Such rights-of-way shall include strips of land twenty feet wide on both sides of all natural channels wider than twenty-five feet. These requirements may be modified or deleted for good cause shown.

(Ord. No. 1722, pt. 5, § 5; Ord. No. 2199, § 11)

(a) Lot Area.

(1) No residential lot shall be created which contains less than seven thousand square feet of area exclusive of street right-of-way, except as provided in this article.

(2) In any area zoned to require a development plan, no change in the size, shape, or area of the original parcel shall be approved by lot split, subdivision or otherwise, except in substantial conformity with an approved development plan and with the size, shape, and area of the parcels shown on the development plan. As an alternative to filing a development plan, approval may be given when all parcels conform substantially to the size, shape, and area requirements of the most restrictive abutting zone district unless otherwise provided in the applicable zoning regulations.

(3) In determining the minimum lot area of lots less than ten thousand square feet in size, public utilities transmitting line easements may be required to be excluded from the minimum lot area, required by the zoning ordinance, or this article but may be included in the lot design.

(b) Lot Width. No residential lot shall be created which has an average width of less than sixty-five feet except as otherwise provided by open space requirements of the zoning ordinance. All corner lots shall have an average width of at least seventy-five feet.

(c) Lot Depth. No lot shall be created the rear line of which is less than one hundred feet from the front line of the lot, except that one side line may be less than one hundred feet in length if it terminates at a corner curve or cul-de-sac turn-around curve. In the case of through lots or corner lots, at least one lot line must be parallel to and not less than one hundred feet distant from the street on which the lot fronts. The rear line of a lot shall be considered as any lot line other than a front line which does not intersect the right-of-way line of the street on which the lot fronts.

(d) Lot Lines. The side lines of all lots shall be approximately at right angles to the street on which the lot faces, or approximately radial if the street is curved. Lot lines which cross any city boundary shall not be approved.

(e) Corner Radius. Property lines of corner lots shall be rounded at the street corner by a radius of not less than fifteen feet. Corner business lots shall have an angular cut-off measurement not less than fifteen feet along each street from the corner.

(Ord. No. 1722, pt. 5, § 6)

The regulations of section 21-24, Lots, may be modified by the advisory agency in the case of a subdivision being developed pursuant to a development plan or open space provisions in accord with zoning regulations. The advisory agency shall prescribe conditions deemed necessary to the public interest.

(Ord. No. 1722, pt. 5, § 7; Ord. No. 3287, § 2)

In subdividing property, due consideration shall be given to the dedication or reservation of parkways, landscaped rights-of-way and open spaces, of suitable sites for parks, playgrounds, and schools and the establishing of other open area for public use. The location of these features shall conform as nearly as possible to any adopted general plan of the county.

(Ord. No. 1722, pt. 5, § 8)

Whenever property is proposed to be subdivided for a use or purpose different from that permitted by the applicable zoning regulations, or which is in conflict with the general plan, a formal request for rezoning of the subject property to appropriate zone districts, and, where deemed appropriate by the planning director, a formal request for amendment of the general plan shall be filed concurrently with the filing of the tentative subdivision map. No tentative subdivision map shall be approved unless and until appropriate changes in zoning regulations to permit the proposed use and purposes of such subdivision have first been recommended and acted upon by the advisory agency in the first instance and by the board of supervisors where its action is needed.

(Ord. No. 1722, pt. 5, § 9)

In all subdivisions, due regard shall be given to the preservation of all natural features such as large trees, natural groves, watercourses, scenic points, historic spots, and similar community assets which will add attractiveness and value to the property if preserved.

(Ord. No. 1722, pt. 5, § 10)

Fire hydrants may be required where recommended by the county fire chief or appropriate special fire district and failure to provide for them may be cause for denial for the subdivision or lot split.

(Ord. No. 1722, pt. 5, § 11; Ord. No. 2199, § 12)

At the time the subdivider presents a final map to the board of supervisors there shall be presented certificates executed respectively by the various public utility companies authorized to serve in the area of the subdivision, certifying that satisfactory provisions have been made with each of such public utility companies as to location of their facilities and that satisfactory easement where required by such companies have been executed and delivered to the certifying companies for recording. Easements for public utility companies shall be designated on the final map as "easements for public utilities."

(Ord. No. 1722, pt. 5, § 11; Ord. No. 2199, § 13)

The advisory agency may authorize modifications from these regulations when in its opinion better design will result. The advisory agency shall prescribe conditions deemed necessary to the public interest and which have a direct relation to the granting of the modification.

(Ord. No. 1722, pt. 5, § 13)

Where necessary to obtain adequate drainage from a lot, setback distances may be required to be increased.

(Ord. No. 1722, pt. 5, § 14)

A. Purpose and Intent. The purpose of agricultural buffers is to implement Comprehensive Plan policies that assure and enhance the continuation of agriculture as a major viable production industry in Santa Barbara County through establishing development standards that provide for the creation of buffers between agricultural uses and new non-agricultural development and uses. The intent of agricultural buffers is to minimize potential conflicts between agricultural and adjacent land uses that result from dust, light, noise and odor incidental to normal agricultural operations as well as potential conflicts originating from residential and other non-agricultural uses (e.g., domestic pets, insect pests and invasive weeds).

B. Applicability. This section applies to all discretionary applications regulated by this chapter 21, Land Division, of the County Code which satisfy all of the following criteria:

1. The project site is located within an urban area, inner-rural area, or existing developed rural neighborhood, as designated on the Comprehensive Plan maps; or located on property zoned industrial that is located in the rural area as designated on the Comprehensive Plan maps.

2. The project site is located immediately adjacent to land that is:

a. Located in a rural area as designated on the Comprehensive Plan maps; and

(1) Has an agricultural zone designation as identified in Section 35.014.020 (Zoning Map and Zones) of section 31-1, the Santa Barbara County Land Use and Development Code, or Section 35.404.020 (Zoning Map and Zones) of section 31-2, the Santa Barbara County Montecito Land Use and Development Code or section 35-52 (Zoning District Designations and Applicability) of article II, the Santa Barbara County Coastal Zoning Ordinance or article V of Ordinance No. 661, excluding state or federally owned land; or

(2) Is subject to a contract executed in accordance with the County Uniform Rules for Agricultural Preserves and Farmland Security Zones.

C. Exceptions. This section does not apply to the following:

1. Modifications to Conditional Certificates of Compliance, Final and Parcel Maps, and Lot Split Plats. Applications for modifications to recorded conditional certificates of compliance, final and parcel maps, and lot split plats, provided that prior to an action by the decision-maker to approve or conditionally approve the application, the decision-maker shall first determine that the proposed modification to the project does not result in any new or greater impacts to agriculture than those resulting from the already approved project.

a. If the decision-maker cannot make the determination required in compliance with subsection C.1 (Modifications to Conditional Certificates of Compliance, Final and Parcel Maps, and Lot Split Plats), above, then the project shall be subject to the provisions of this section 21-32A (Agricultural Buffers).

2. Lot line adjustments and modifications to lot line adjustments that:

a. Do not exceed a ten percent increase or decrease in the area of the smallest existing lot; and

b. Do not result in a greater number of residential developable parcels than existed prior to the adjustment in compliance with subsection 21-93.a.3.a.3 of this chapter or do not result in an increased number of dwelling units or a greater density than the approved lot line adjustment in compliance with subsection 21-15.9(h)7 of this chapter, as applicable.

3. Non-commercial Agricultural Uses. An agricultural buffer is not required adjacent to a common lot line between the project site and an adjacent agriculturally zoned lot if the adjacent lot is used for non-commercial agriculture.

D. Agricultural Buffer Requirements. All applications subject to this section shall designate and maintain an agricultural buffer on the project site in compliance with this section.

1. Agricultural Buffer Width. The width of the agricultural buffer shall be in compliance with the range of agricultural buffer widths as shown in the following table. Ranges are provided because unique circumstances may require the buffer width to be adjusted; however, the agricultural buffer width as adjusted shall neither be less than the minimum buffer width nor greater than the maximum buffer width shown in Table 21-32A-1 (Range of Agricultural Buffer Width), below. If the proposed project is located adjacent to a lot that contains both production agriculture and rangeland or pastureland, then the most protective buffer:

a. Shall be applied adjacent to any portion of the common lot line between the project site and the adjacent agriculturally zoned lot where production agriculture is immediately adjacent; and

b. May be applied to any portion of the common lot line between the project site and the adjacent agriculturally zoned lot where production agriculture is not immediately adjacent, if production agriculture is located on the adjacent lot within the distance as measured from the common lot line, that is equal to the width of the required buffer that would otherwise be applicable to the project site.

Refer to section II.C. (agricultural buffer width adjustment) of the Agricultural Buffer Implementation Guidelines (Appendix B) for guidance.

Table 21-32A-1. Range of Agricultural Buffer Width

_____

2. Agricultural Buffer Location. The agricultural buffer shall be located:

a. On the lot on which the project is proposed.

b. Adjacent to the common lot line between the project site and the adjacent agriculturally zoned lot.

3. Agricultural Buffer Width Measurement. The agricultural buffer width shall be measured from the common lot line between the project site and the adjacent agriculturally zoned lot. The agricultural buffer shall be coterminous with the length of said common lot line.

4. Agricultural Buffer Width Adjustment. The following factors shall be considered when determining the appropriate agricultural buffer width in compliance with subsection D.1 (agricultural buffer width). See the Agricultural Buffer Implementation Guidelines (Appendix B) for guidance in determining the appropriate agricultural buffer width.

a. Site-Specific Factors. The following factors shall be considered when determining the agricultural buffer width:

(1) Crop type/agricultural practices.

(2) Elevation differences and topography.

(3) Extent and location of existing non-agricultural development.

(4) Location of existing roads or naturally occurring barriers.

(5) Historical land use on the agricultural lot.

(6) Future farming potential of the agricultural lot.

(7) Site design of the non-agricultural proposal.

(8) Non-agricultural lot size/configuration.

(9) Prevailing wind direction.

b. Vegetative Screening Adjacent to Production Agriculture. Vegetative screening may be used to offset an increase in the buffer width for projects adjacent to production agriculture, as it may be adjusted in compliance with subsection D.4.a (Site-specific factors). See subsection F.3 for vegetative screening criteria and the Agricultural Buffer Implementation Guidelines (Appendix B) for guidance in determining if an offset may be appropriate.

c. Constrained Agricultural Areas. If the adjacent lot is used for production agriculture and contains land areas that are constrained by physical features or easements such that those land areas cannot be used for agriculture, then the agricultural buffer width may be reduced on the project site by an amount equal to the width of the constrained land area located on the adjacent agricultural lot, provided:

(1) The physical feature is permanently part of the landscape (e.g., a protected riparian area, or rock out-cropping); and

(2) The physical feature or easement precludes any kind of agricultural use and be located adjacent to the non-agricultural project site.

5. Comprehensive Plan Consistency. Where Comprehensive Plan policies and this section 21-32A (Agricultural Buffers) both address agricultural buffer requirements, the most protective agricultural buffer requirement shall prevail.

6. Reasonable Use. This section is not intended, and shall not be construed as authorizing the decision-maker acting in compliance with this section 21-32A (Agricultural Buffers) to exercise their authority to approve, conditionally approve or deny an application in a manner which will take or damage private property for public use without the payment of just compensation therefore. This section is not intended to increase or decrease the rights of any owner of property under the Constitution of the State of California or the United States or under this chapter 21 (Land Division) of the County Code.

7. Buffer Recordation.

a. Separate document required to record information.

(1) A separate document and/or additional map sheet in compliance with subsection D.7.a.(2), below shall be:

(a) Filed or recorded simultaneously with the final or parcel map subject to this section.

(b) Included in the project description of a conditional certificate of Compliance subject to this section 21-32A (Agricultural Buffers) prior to approval or conditional approval in compliance with division 13, Certificates of Compliance and Conditional Certificates of Compliance, of article I, Subdivisions, of this chapter.

(c) Included in the project description of a lot line adjustment subject to this section 21-32A (Agricultural Buffers) prior to approval or conditional approval in compliance with article III, Lot Line Adjustments, of this chapter.

(d) Included in the project description of a modification to a final or parcel map, lot split plat or lot line adjustment subject to this section 21-32A (Agricultural Buffers) prior to approval or conditional approval in compliance with division 3, Modifications to Recorded Maps, Lot Split Plats and Lot Line Adjustments, of article I, Subdivisions, of this chapter.

(2) Said document or additional map sheet shall include and depict, as applicable:

(a) An exhibit showing the location of the agricultural buffer by metes and bounds description or surveyor's description.

(b) The uses that are allowed within the agricultural buffer in compliance with subsection E (allowable uses within agricultural buffers).

(c) The landscape, lighting and irrigation plan required in compliance with subsection F (agricultural buffer landscape, lighting and irrigation plan requirements).

(d) The maintenance plan required in compliance with subsection G (agricultural buffer maintenance requirements).

(3) The requirement to record said separate document and/or additional map sheet in compliance with this subsection D.7 (buffer recordation) shall be included as a condition of approval of a discretionary application subject to this section 21-32A (Agricultural Buffers).

E. Allowable Uses Within Agricultural Buffers. The property owner shall use his best efforts to consult with the adjacent agricultural land owner(s) to address food safety and agricultural production concerns with regard to landscape, lighting, and vegetative screening design and siting. See the Agricultural Buffer Implementation Guidelines (Appendix B) for information on the purpose and intent of restricting uses within agricultural buffers and how to incorporate site design and other features that are compatible with agriculture.

1. Unrestricted Uses Within Agricultural Buffers. Subject to other provisions of this section, or other provisions of the County Code, the following uses may be allowed within a designated agricultural buffer:

a. Drainage channels, irrigation canals, storm water retention basins and low impact development (LID) drainage features.

b. Fences and walls.

c. Low-lying landscaping and vegetative screening that does not include trees or hedges exceeding three feet in height.

d. Oil and gas, wind energy and cogeneration facilities that are:

(1) Permitted in compliance with:

(a) Article 35.5 (Oil and Gas, Wind Energy and Cogeneration Facilities) of section 35-1, the Santa Barbara County Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

(b) Chapter 35.446 (Wind Energy Conversion Systems) of section 35.-2, the Santa Barbara County Montecito Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

(c) Division 9 (Oil and Gas Facilities) of article II, the Santa Barbara County Coastal Zoning Ordinance, of chapter 35, Zoning, of the County Code.

(2) Operated in compliance with:

(a) Chapter 35.101 (Nonconforming Uses, Structures, and Lots) of section 35-1, the Santa Barbara County Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

(b) Chapter 35.491 (Nonconforming Uses, Structures, and Lots) of section 35-2, the Santa Barbara County Montecito Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

(c) Division 10 (Nonconforming Structures and Uses) of article II, the Santa Barbara County Coastal Zoning Ordinance, of chapter 35, Zoning, of the County Code.

e. Natural waterways including creeks, flood plains, lakes, ponds and rivers.

f. Signs.

g. Solar energy systems that are allowed as an accessory use to the principal use in compliance with:

(1) Section 35.30.160 (Solar Energy Systems) of section 35-1, the Santa Barbara County Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

(2) Section 35.430.160 (Solar Energy Systems) of section 35-2, the Santa Barbara County Montecito Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

(3) Article II, the Santa Barbara County Coastal Zoning Ordinance, of chapter 35, Zoning, of the County Code.

h. Telecommunication facilities permitted in compliance with:

(1) Chapter 35.44 (Telecommunication Facilities) of section 35-1, the Santa Barbara County Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

(2) Chapter 35.444 (Telecommunication Facilities) of section 35-2, the Santa Barbara County Montecito Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

(3) Section 35-144F (Commercial Telecommunication Facilities) of article II, the Santa Barbara County Coastal Zoning Ordinance, of chapter 35, Zoning, of the County Code.

i. Utility lines and facilities.

j. Any other use determined by the decision-maker to be consistent with the purpose and intent of the buffer requirement.

k. Modifications or additions to structures legally existing as of the effective date of the ordinance codified in this section provided that any addition to a structure that is located within a buffer required by this section 21-32A (Agricultural Buffers) shall not extend further towards the immediately adjacent agricultural lot.

2. Restricted Uses Within Agricultural Buffers. Subject to other provisions of this section, or other provisions of the County Code, the following uses may be allowed within the agricultural buffer provided they are not located any closer to the common lot line between the project site and the adjacent agriculturally zoned lot than half the width of the buffer. This requirement may be modified when the decision-maker determines that strict compliance with this subsection E.2 is not required to minimize conflicts with adjacent agriculture.

a. Industrial or commercial loading docks and rear service areas.

b. Landscaping and vegetative screening.

c. Lighting.

d. Non-habitable structures such as those used for storage.

e. Parking areas including carports and garages.

f. Public and private open space areas with limited passive recreational uses such as trails, bike paths and walking paths.

g. Roads and transportation infrastructure.

3. Prohibited Uses Within Agricultural Buffers. Recreational uses such as parks, picnic areas, playgrounds and ball fields shall not be allowed in an agricultural buffer.

4. Open Space Credit. The agricultural buffer may be counted toward open space requirements as long as the limits on allowed uses are consistent with the requirements of this section and the requirements in:

a. Section 35-1, the Santa Barbara County Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

b. Section 35-2, the Santa Barbara County Montecito Land Use and Development Code, of chapter 35, Zoning, of the County Code; or

c. Article II, the Santa Barbara County Coastal Zoning Ordinance, of chapter 35, Zoning, of the County Code.

5. The unrestricted uses, restricted uses and prohibited uses within the designated agricultural buffer shall be included as a condition of approval of the approved project.

F. Agricultural Buffer Landscape, Lighting and Irrigation Plan Requirements.

1. A Landscape, lighting and irrigation plan (plan) shall be required for all agricultural buffers. The plan shall:

a. Graphically depict and label the agricultural buffer.

b. Graphically depict and label the following elements within the agricultural buffer:

(1) Erosion control measures.

(2) Hardscape.

(3) Irrigation systems.

(4) Landscaping, vegetation, and materials.

(5) Lighting.

c. Incorporate low impact development (LID) measures to maximize runoff retention and groundwater infiltration on-site.

d. Incorporate a fence or other barrier a minimum of six feet in height that complies with chapter 35, Zoning, of the County Code, that discourages trespassing and domestic animals from crossing the common lot boundary between the project site and the adjacent agricultural land.

e. Prohibit the planting or installation of turf within fifty feet of the adjacent agricultural land unless required by county, state or federal regulations.

f. Be compatible with the surrounding land uses and rural character of the agricultural area.

2. Landscaping, lighting and irrigation are not required within the agricultural buffer. However, if vegetation is included within the buffer, the plant palette shall meet the following requirements:

a. The plants shall be compatible with agriculture.

b. Shading of adjacent agricultural crops shall be minimized.

c. To the maximum extent feasible, the plants shall be fire resistant and drought-tolerant or low water use.

d. The plants shall not be considered noxious according to Section 4500 of the California Code of Regulations or considered invasive by the California Invasive Plant Council (Cal-IPC).

3. If a vegetative screen is used to offset an agricultural buffer width increase for production agriculture as described in subsection D.4.b (vegetative screening adjacent to production agriculture), the vegetative screen shall be consistent with the requirements in this subsection F (agricultural buffer landscape, lighting and irrigation plan requirements) and shall be in compliance with the following additional criteria:

a. The vegetative screen shall consist of two staggered rows of vegetation consisting of a layered canopy with evergreen trees and shrubs with foliage extending from the base to the crown.

b. The plants shall thoroughly screen the agricultural use from the non-agricultural use within five years from time of installation.

c. The minimum height of trees at maturity shall be fifteen feet.

d. The vegetative screen shall be at least twenty-five feet deep.

4. The landscape, lighting and irrigation plan shall be compatible with the requirements in subsection E (allowable uses within agricultural buffers).

5. The applicant shall provide a signed and notarized agreement and a performance security acceptable to the director of the planning and development department that guarantees the installation of landscaping, lighting and irrigation and provides for the successful establishment of the agricultural buffer for a minimum of five years. The performance security shall be released upon approval by the director of the planning and development department.

G. Agricultural Buffer Maintenance Requirements.

1. A maintenance plan shall be required that provides for the maintenance of the agricultural buffer for the life of the project. The maintenance plan shall:

a. Include provisions for managing agricultural pests such as vertebrate pests, invasive weeds, and crop threatening insects. Integrated pest management practices shall be used to the extent feasible.

b. Include provisions for removing debris, trash and weeds.

c. Provide for regular fuel management and removal of accumulated plant matter within the agricultural buffer so as to minimize fire risk.

d. Be consistent with the requirements in subsection F (agricultural buffer landscape, lighting and irrigation plan requirement).

e. Provide for the regular maintenance of the elements as described in Subsection F (agricultural buffer landscape, lighting and irrigation plan requirement).

H. Future Conversion of Adjacent Agricultural Land. If the underlying purpose for the agricultural buffer no longer exists, the decision-maker, upon application for modification in compliance with division 3 (Modification to Recorded Maps, Lot Split Plats and Lot Line Adjustments) of article I, Subdivisions, of chapter 21, Land Division, of the County Code, may modify conditions of approval of the project for the agricultural buffer requirements originally required in compliance with this section 21-32A (Agricultural Buffers).

I. Findings. In addition to other findings that may be required, the decision-maker shall not approve or conditionally approve any application subject to the requirements of this section for which an agricultural buffer is required unless it first makes all of the following findings:

1. The design and configuration of the agricultural buffer minimizes, to the maximum extent feasible, conflicts between the existing adjacent agricultural uses and existing uses or zoning of the non-agricultural project site in compliance with the Comprehensive Plan, including applicable Area and Community Plans, the Coastal Land Use Plan, this Section, and chapter 35, Zoning, of the County Code.

2. The landscape, lighting, irrigation and maintenance plans are compatible with the character of the adjacent agricultural land and the rural setting.

(Ord. No. 4854, § 4, 4-16-2013)