Chapter 19.770 — SITE PLAN REVIEW PERMIT

The site plan review permit process is established to meet certain community goals that include the following:

A.

To ensure that the highest quality of land planning is incorporated into development projects;

B.

To ensure that new projects are compatible with existing neighborhoods in terms mass, scale and functionality;

C.

To ensure that development occurs with due regard to environmental factors;

D.

To provide for public improvements necessitated by the development; and

E.

To promote orderly, attractive and harmonious development, and promote the general welfare by preventing the establishment of uses or erection of structures that are not properly related to or that would adversely impact their sites, surroundings, traffic circulation or environmental setting.

(Ord. 7573 § 1(Exh. A), 2021; Ord. 7331 §112, 2016; Ord. 6966 §1, 2007)

A.

General process. Site plan review permit (SPR) applications shall be processed in accordance with the discretionary permit processing provisions as set forth in Chapters 19.650 (Approving Authority), 19.660 (General Application Processing Procedures), 19.670 (Notices and Hearings), 19.680 (Appeals), 19.690 (Effective Dates) and other applicable chapters of the Zoning Code.

(Ord. 7573 § 1(Exh. A), 2021; Ord. 7331 §112, 2016; Ord. 6966 §1, 2007)

The following commercial or mixed-use projects require a site plan review permit:

A.

Commercial. In addition to any other permits required by the Zoning Code, no new building, structure, exterior alteration or enlargement of an existing building or structure exceeding 10,000 square feet shall be commenced in the Commercial Regional Center Zone (CRC) (Chapter 19.110) until a Site Plan Review Permit has been granted pursuant to this chapter.

B.

Mixed-Use. In addition to any other permits required by the Zoning Code, no new building, structure or exterior alteration or enlargement of an existing building or structure exceeding 20,000 square feet of nonresidential space or 20 residential units, whichever is greater, shall be commenced in any Mixed-Use Village or Urban Zones (Chapter 19.120) until a site plan review permit has been granted pursuant to this chapter.

C.

Planning Commission requirement. The Planning Commission, at its discretion, may require a site plan review permit as a condition for any project.

D.

Exemption.

1.

Any site plan review included as part of the review for conditional use permits, minor conditional use permits and planned residential development permits and design review is subject to the requirements of Chapters 19.730 (Minor Conditional Use Permit), 19.760 (Conditional Use Permits) and 19.780 (Planned Residential Development Permit) and is therefore exempt from the requirement of a separate site plan review permit unless such site plan review is deferred at the time of approval of such permits.

2.

Stand-alone multi-family or age-restricted senior residential uses in any Mixed-Use zone are permitted by right subject to Chapter 19.710 - Design Review, and do not require a Site Plan Review.

(Ord. 7573 § 1(Exh. A), 2021; Ord. 7487 § 26, 11-5-2019; Ord. 7408 §1, 2018; Ord. 7331 §112, 2016; Ord. 7235 §19, 2013; Ord. 7091 §13, 2010; Ord. 6966 §1, 2007)

In order to achieve the purposes of this chapter, the approving or appeal authority may require reasonable conditions of approval on a site plan review permit including, but not limited to the following.

A.

Special conditions or requirements to revise the site plan, that are more restrictive than the development standards in the underlying base zone or including, but not limited to, the following:

Building height, bulk or mass;

Setbacks;

Lot coverage;

Lighting;

5.

Private and common open space and/or recreational amenities;

6.

Screening, including garages, trash receptacles, or mechanical equipment;

7.

Landscaping;

8.

Fencing plans;

9.

Parking, access and on-site circulation;

Pedestrian circulation;

Grading;

Street dedication and improvements;

13.

Public improvements either on or off the subject site that are needed to service the proposed development;

14.

Project phasing;

15.

Any other revisions to the site plan or operational conditions deemed necessary to further the purposes of this title.

B.

Reduced development standards for affordable housing projects in accordance with the provisions of Chapter 19.545 (Density Bonus).

(Ord. 7660, § 17, 2024; Ord. 7573 § 1(Exh. A), 2021; Ord. 7331 §112, 2016; Ord. 6966 §1, 2007)

19.770.050 - Findings.

The Planning Commission may approve a Site Plan Review for development upon making the following findings:

A.

The proposed development is consistent with the General Plan, any applicable specific plans and the intent and purpose of the base zone.

B.

The proposed development, as conditioned, will not have substantial adverse effects on the surrounding property or uses, and will be compatible with the existing and planned land use character of the surrounding area.

C.

The proposed development is appropriate for the site and location. In mixed-use zones, the proposed development fosters a mixture of variety of land uses within the zone and the general vicinity and contributes to a synergistic relationship between uses.

D.

Buildings within a mixed-use development project must be compatible with each other and be designed as an integrated, unified project. All proposed development must meet the design standards and guidelines in Section 19.120.070 (Design Standards and Guidelines).

(Ord. No. 7701, § 46, 2025)

Chapter 19.780 - PLANNED RESIDENTIAL DEVELOPMENT PERMITS

19.780.010 - Purpose.

A.

These Planned Residential Development (PRD) regulations are established to allow for flexibility and creativity in design of single-family residential developments, and for the application of unique development standards that reflect special property conditions. Specifically, Planned Residential Development Permits are intended to achieve the following:

1.

In all applicable zones:

a.

Address the need to provide mechanisms to assist in producing a diversity of single-family residential housing and product types;

b.

Provide an incentive for clustered property development of environmentally and topographically constrained land in order to minimize the impacts of development on more environmentally sensitive portions of that land, particularly in the RC Zone;

c.

Allow the development of small-lot infill subdivisions in existing neighborhoods, thereby allowing a more efficient and creative use of often difficult to develop properties when the proposed development is designed in a manner that is compatible with all existing development in the vicinity;

d.

Encourage and allow more creative and imaginative project design by allowing increased development densities. In return, planned residential developments are required to incorporate open space, amenities for recreational and visual enjoyment and superior design features, which are encouraged, but not required of standard single-family residential developments;

e.

To provide increased opportunities for home ownership consistent with the objectives of the City's General Plan; and

f.

Assist in the preservation and enhancement of valuable natural areas, where appropriate and especially in the RC Zone.

2.

In the RC Zone: PRD's in the Residential Conservation Zone (RC) shall be established consistent with General Plan objectives and voter approved initiatives (Proposition R and Measure C) to protect prominent ridges, hilltops and hillsides, slopes, arroyos, ravines and canyons, and other areas with high visibility or topographic conditions that warrant sensitive development from adverse development practices, and specifically, to achieve the following objectives:

a.

To promote clustering of lots on less sensitive portions of the property to preserve valuable open space and wildlife habitat;

b.

To provide each individual lot with its own private open space areas preserving natural open space areas and features in common open space areas pursuant to Proposition R and Measure C; and

c.

To promote the preservation of viewscapes and low impact development.

(Ord. 7683, § 18, 2024; Ord. 7331 §113, 2016; Ord. 7027 §3, 2009; Ord. 6966 §1, 2007)

19.780.020 - Applicability and permit requirements.

A Planned Residential Development is permitted according to the following permit types:

1)

Planned Residential Development Permit.

a)

Permitted in single-family residential zones except the RA-5 zone.

b)

Consists of any number of dwelling units.

2)

Minor Planned Residential Development Permit (Minor PRD).

a)

Permitted in single-family residential zones except the RC and RA-5 zone.

b)

Consists of five to 16 dwelling units.

3)

Administrative Planned Residential Development Permit (Admin PRD).

a)

Permitted in single-family residential zones except the RC and RA-5 zone.

b)

Consists of four or fewer parcels.

Small Lot Subdivision Planned Residential Development Permit (Small Lot PRD).

a)

Permitted in multi-family (R-3) residential zones except for R-4.

b)

Consists of 16 or fewer dwelling units.

The Approving Authority shall review and evaluate a proposed project, including plot plans, architectural plans, grading plans, tract or parcel map, and proposed amenities, and shall approve, conditionally approve, or deny the proposed project, based on the findings and criteria indicated in Section 19.780.050.A for singlefamily residential zones or Section 19.780.055.B for R-3 zones.

(Ord. 7683, § 19, 2024; Ord. 7331 §113, 2016; Ord. 6966 §1, 2007)

19.780.030 - Procedures.

A.

General process. All Planned Residential Development Permit (PRD) applications shall be processed in accordance with the discretionary permit processing provisions as set forth in Chapters 19.640 (General Permit Provisions), 19.650 (Approving and Appeal Authority), 19.660 (General Application Processing Procedures), 19.670 (Public Hearings and Notice Requirements), 19.680 (Appeals), 19.690 (Effective Dates, Time Limits, and Extensions) and other applicable Chapters of the Zoning Code.

B.

Map required. The application shall be accompanied by a tentative map that shall be filed with the Planning Division in accordance with procedures set forth in Chapter 18.080 of Title 18 (Subdivision Code).

C.

Phasing. If a Planned Residential Development is proposed to be constructed in phases, the proposed phasing schedule is subject to approval by the Director of Community & Economic Development.

D.

Planned Residential Development permit expiration. Time limits and extensions shall be the same as for the related subdivision, consistent with the provisions of Title 18 (Subdivision Code) prior to issuance of the first building permit. After the first building permit has been pulled the Planned Residential Development Permit is vested.

E.

Voting approval requirements. The decision of Planning Commission to grant a Planned Residential Development Permit shall require an affirmative vote of 2/3 of the membership present and voting.

(Ord. 7683, § 20, 2024; Ord. 7331 §113, 2016; Ord. 6966 §1, 2007)

19.780.040 - Permitted uses.

A.

Single-family dwellings attached or detached.

B.

Tiny home (foundation) in a tiny home community, except in the RC Zone.

C.

Related recreation and community facilities for the use of residents of the development and their guests.

D.

Natural open spaces.

E.

Golf courses.

F.

Multipurpose trails.

G.

Other uses as may be permitted as part of the planned residential development.

H.

In the single-family residential base zones, uses required by State law to be permitted in conjunction with a single-family residential use.

(Ord. 7528 §1(Exh. A), 2020; Ord. 7520 §1(Exh. A), 2020; Ord. 7408 §1, 2018; Ord. 7331 §113, 2016; Ord. 7027 §4, 2009; Ord. 6966 §1, 2007)

19.780.050 - Density and findings for single-family residential zones.

A.

Benchmark density and findings for approval. In all single-family residential zones, densities up to the densities shown in Table 19.780.050 B (PRD Benchmark and Bonus Densities) for the underlying zone in which the project is located may be approved with the granting of a Planned Residential Development Permit, Minor Planned Residential Development Permit, or Administrative Planned Residential Development Permit, provided that the Approving Authority determines, based on demonstrated evidence, the project complies with the following criteria and findings, and the intent, standards, and requirements of this chapter. Additional density up to the limit of the bonus density shown in Table 19.780.050.B may be considered if the project meets all the requirements stated in Section 19.780.050.E - Density Bonus for Superior Design.

Compliance with the following criteria shall be demonstrated for a proposed project to be approved, and the benchmark density to be granted. Failure to substantially meet or exceed all these standards shall result in disapproval of the project, or a lower density than the benchmark density.

1.

In all single-family residential zones, other than RA-5 and RC Zone:

a.

The property is well served by public infrastructure;

b.

The project enjoys good access to public services, including schools, shopping and public and semipublic facilities;

c.

The site is located on streets capable of accommodating the anticipated traffic. A traffic study may be required;

d.

The project complies with the purpose and standards of this chapter, demonstrates substantial compliance with the provisions of the Citywide Design and Sign Guidelines, and is in accordance with City Codes, which may include deviations by variances when required findings are made. Additional criteria used in evaluating the design of the project shall include, but shall not be limited to, the following:

i.

Varied placement of buildings demonstrating sensitivity to the natural topographic features of the site;

ii.

Relatively level land is set aside for active recreational pursuits;

iii.

Open space is distributed on the site and accessible to all units

iv.

An efficient circulation system consisting of both vehicular lanes and pedestrian walkways;

v.

Sensitivity to surrounding community and attention to the edge conditions, creating areas of transition from surrounding existing development to the proposed development; and

vi.

Where front porches are consistent with the style of the development, a minimum of two-thirds (⅔) of the total units shall provide front porches;

e.

The project proposes development in an environmentally and topographically sensitive manner in order to minimize the impacts of development on adjacent properties, and is designed in a manner that is compatible with the adjacent and existing development in the vicinity;

f.

The project provides amenities in compliance with this chapter, and that the amenities are consistent with the size and scale of the project, the project density, and neighborhood characteristics.

In the RC Zone:

a.

Retention of unique natural features, including arroyos, hillsides and rock outcroppings, in natural open space areas consistent with the grading ordinance;

b.

Placement of buildings demonstrating sensitivity to the natural topographic and habitat features of the site, including clustering of homes in less sensitive and less steep locations in order to preserve such natural features and valuable natural open space, both for wildlife habitat and visual aesthetic purposes;

c.

Provision of other amenities consistent with the RC Zone and as deemed appropriate for the project;

d.

Provision that the development will not introduce non-native plants as defined by Table 6-2 of the Multiple Species Habitat Conservation Plan (MSHCP) into the landscape adjacent to the City's arroyos in perpetuity;

e.

Maintenance and management of all open space easements by a single entity for the entire project with an appropriate natural open space management plan;

f.

Superior design of individual dwelling site plans and building architecture, including such features as porches and garages set back from the street in comparison to the house, and detailed four sided, building treatments. Many of the desirable features are found in the adopted Citywide Design and Sign Guidelines. The design of custom homes will be reviewed as individual homes are submitted for design review approval prior to building permit issuance;

g.

Sensitivity to impacts of the development on surrounding uses, including linkages to natural open space areas where appropriate; and

h.

Streets serving the development shall be capable of accommodating the anticipated traffic.

B.

Maximum density. The maximum density of a PRD project shall be consistent with this chapter, the underlying General Plan land use designation(s), any applicable Specific Plan(s), as well as Table 19.780.050 B below.

Table 19.780.050.B

PRD Benchmark and Bonus Densities

C.

No PRD shall be granted approval if the project's base zone and General Plan land use designation are inconsistent, pursuant to General Plan Tables LU-5, LU-6 and LU-7.

D.

Transfer of density. When two or more General Plan land use designations or base zones exist within a planned residential development, the density may be transferred between designation and/or zones within the same development as necessary to provide for a superior development based upon good planning principles, and to promote the general welfare of the neighborhood and maximum benefit to the natural environment. In particular, such transfers are desirable

where density is transferred from steep, hillside land to flatter, less visually sensitive properties where significantly less grading is required. In the case of such a density transfer, the overall maximum density shall not exceed that otherwise permitted by the General Plan designation(s) (See 19.780.050.B). The only exception is that density cannot be transferred from a non-RC zoned property to an RC zoned property. For purposes of this section, a project may consist of more than one underlying legal parent parcel; however, such parcels must be contiguous unless separated by an existing public or private street.

E.

Density bonus for superior design. A PRD project may qualify for a density bonus up to the maximum shown in Table 19.780.050.B, provided that it meets the standards of Section 19.780.050.A, and satisfies the following criteria beyond those in 19.780.050.A.

1.

All single-family residential zones, other than RA-5 and RC:

a.

Except for Administrative PRD and Minor PRD projects, evidence that the project can be certified in LEED, National Green Building Standard, or an equivalent standard; and

b.

Except for Small Lot PRD projects, evidence shall be provided to document that the project includes a minimum of three of the following for Administrative PRDs, four of the following for Minor PRD, and five of the following for the PRD permit:

(1)

Designate all streets, sidewalks and trails that are built as part of the project or serving the project directly as available for general public use and not gated. Gated areas and enclaves are NOT considered available for public use.

(2)

Design the building orientation for solar design, including the following provisions:

a.

The glazing area on the north- and south-facing walls of the building is at least 50 percent greater than the sum of the glazing area on the east- and west-facing walls.

b.

The east-west axis of the building is within 15 degrees of due east-west.

c.

The roof has a minimum of 450 square feet of south-facing area that is oriented appropriately for solar applications.

d.

At least 90 percent of the glazing on the south-facing wall is completely shaded (using shading, overhangs, etc.) at noon on June 21 and unshaded at noon on December 21.

(3)

Locate the project within a one-quarter mile of 11 basic community resources (Table 19.780.050.A), within a one-half mile of 14 basic community resources (Table 19.780.050.A) and within a one-half mile of a major transit stop, as defined in California Public Resource Code Section 21064.3.

Table 19.780.050 A Basic Community Resources Arts and entertainment center Bank Community or civic center Convenience store Daycare center Fire station Fitness center or gym Laundry or dry cleaner Library Medical or dental office Pharmacy

Police station Post office Place of worship Restaurant School Supermarket Other neighborhood-serving retail Other office building or major employment center Note: Up to two of each type of community resource may be counted. For example, two restaurants within one-quarter mile may be counted as two community resources; four restaurants also count as two.

(4)

Locate trees or other plantings to provide shading for at least 50 percent of sidewalks, patios and driveways. Shading should be calculated for noon on June 21, when the sun is directly overhead, based on five year's growth.

(5)

Install light-colored high-albedo materials or vegetation for at least 50 percent of sidewalks, patios and driveways.

a.

Acceptable strategies include the following:

i.

White concrete;

ii.

Gray concrete;

iii.

Open pavers (counting only the vegetation, not pavers); and

iv.

Any material with a solar reflectance index (SRI) of a least 29.

(6)

Design the lot such that at least 70 percent of the built environment, not including area under roof, is permeable and designed to capture water runoff for infiltration on-site. Area that can be counted toward the minimum includes the following:

a.

Vegetative landscape (e.g., grasses, trees, shrubs, etc.).

b.

Permeable paving, installed by an experienced professional. Permeable paving must include porous above-ground materials (e.g., open pavers, engineered products) and a six-inch porous sub-base, and the base layer must be designed to ensure proper drainage away from the home.

c.

Impermeable surfaces that are designed to direct all runoff toward an appropriate permanent infiltration feature (e.g., vegetated swale, on-site rain garden, or rainwater cistern).

(7)

Design and install one of the following permanent erosion control measures:

a.

If portions of the lot are located on a steep slope, reduce long-term runoff effects through use of terracing and retaining walls.

b.

For every 500 feet of disturbed lot area (including the area under the roof), one tree, four 5-gallon shrubs, or 50 square feet of native groundcover shall be planted.

(8)

Design and install one or more of the following runoff control measures:

a.

Install permanent stormwater controls in the form of vegetated swales, on-site rain garden, dry well, or rain-water cistern, or equivalent designed to manage runoff from the homes.

b.

Install a vegetated roof to cover 50 percent or more of the roof area.

c.

Have the site designed by a licensed or certified landscape design or engineering professional such that it is demonstrated that all water runoff for the home is managed through an on-site design element.

(9)

Design and install a rainwater harvesting and storage system (including surface runoff and/or roof runoff) for landscape irrigation use. The storage system must be sized to hold all the water from a one-inch rainfall event (equivalent to 0.62 gallons per square foot of roof area used for capture), taking into consideration the size of the harvest system (i.e., 50 percent of total roof area).

(10)

Design the plumbing with irrigation system water supplied with municipal recycled water.

(11)

Construct the project to exceed Title 24 requirements by 20 percent or more.

2.

In the RC Zone: To protect prominent ridges, hilltops and hillsides, slopes, arroyos, ravines and canyons, and other areas with high visibility or topographic conditions that warrant sensitive development from adverse development practices, thus furthering the intent of Proposition R and Measure C and promoting clustering, all of the following are required:

a.

Require all designated open space areas to be managed and maintained under the stewardship of a recognized conservation group as approved by the Approving Authority, with an endowment to fund such stewardship entirely;

b.

The project shall provide at least six of the items listed in Section 19.780.050.E.1.b above; and

c.

The project shall provide evidence that unique natural features and steeper portions of the property are being preserved in open space, with lots clustered in the less steep portions of the site.

(Ord. No. 7701, § 47, 2025; Ord. 7683, § 21, 2024; Ord. 7481 § 2, 2019; Ord. 7331 §113, 2016; Ord. 7027 §5, 2009; Ord. 6966 §1, 2007)

19.780.055 - Density and findings for Small Lot PRD.

A.

Maximum density. The maximum density of a Small Lot PRD project shall be consistent with the underlying General Plan land use designation and any applicable Specific Plan.

B.

Minimum density. Small Lot PRD projects shall provide a minimum of 50 percent of the density of the underlying General Plan land use designation.

C.

Findings. Compliance with the following criteria shall be demonstrated for a proposed project to be approved. Failure to substantially meet or exceed all these standards shall result in disapproval of the project.

1.

The property is well served by public infrastructure;

2.

The project enjoys good access to public services, including schools, shopping and public and semipublic facilities;

The site is located on streets capable of accommodating the anticipated traffic. A traffic study may be required;

4.

The project complies with the purpose and standards of this chapter, demonstrates substantial compliance with the provisions of the Citywide Design and Sign Guidelines, and is in accordance with City Codes, which may include deviations by variances when required findings are made. Additional criteria used in evaluating the design of the project shall include, but shall not be limited to, the following:

a.

Open space is distributed on the site and accessible to all units;

b.

An efficient circulation system consisting of both vehicular lanes and pedestrian walkways; and

c.

Sensitivity to surrounding community and attention to the edge conditions.

5.

The project proposes development in an environmentally and topographically sensitive manner in order to minimize the impacts of development on adjacent properties, and is designed in a manner that is compatible with the adjacent and existing development in the vicinity.

(Ord. 7683, § 22, 2024)

A.

Relationship to base zone development standards. The development standards set forth in this section, if in conflict with the development standards of the underlying base zone, shall supersede the development standards of the underlying base zone, except in the RC Zone the underlying development standards still apply. This section shall not supersede the development standards of any applicable overlay zone. In cases where a standard is not addressed in this chapter, the standard of the base zone or any applicable overlay zone shall apply. The standards set forth herein are the minimum required for a PRD to qualify for the benchmark density.

B.

Standards for all Planned Residential Developments - RR, RE, and all R-1 Zones.

1.

Lot size and coverage. Minimum lot size and maximum lot coverage requirements to be determined by the Approving Authority on a case specific basis in part based on product type, characteristics of the property and surrounding uses.

2.

Setbacks.

1 Except for Administrative PRD and Minor PRD projects which shall provide perimeter property line setbacks applicable to primary dwellings consistent with the Zone.

Usable open space and recreational facilities

a.

Planned Residential Development Permit.

(1)

A minimum of 500 square feet of usable common open space per dwelling unit is required. The number and type of desirable amenities for a project will be determined on a case-by-case basis in proportion to the size and design of the project. Desirable common open space amenities include, but are not limited to, the following:

a.

Multiple enclosed tot lots with multiple play equipment. The tot lots shall be conveniently located throughout the site. The number of tot lots and their location shall be subject to Planning Commission review and approval;

b.

Pool and spa;

c.

Multi-purpose room equipped with kitchen, defined areas for games, exercises, recreation, private gathering of residents, etc.;

d.

Barbeque facilities equipped with multiple grills, picnic benches, etc. The barbecue facilities shall be conveniently located throughout the site. The number of barbeque facilities and their locations shall be subject to Planning Commission review and approval;

e.

Court facilities (e.g. tennis, volleyball, basketball, etc.);

f.

Jogging/walking trails with exercise stations;

g.

Community garden;

h.

Theater;

i.

Computer room;

j.

Exercise room;

k.

Golf course, putting green, etc.;

l.

Passive recreational facilities tied to existing topographical features, with gazebos, benches, etc.;

m.

Art pieces; and

n.

Water features.

(2)

Private open space.

a.

A minimum of 200 square feet per dwelling unit is required, with no dimension less than ten feet.

b.

Minor Planned Residential Development Permit

(1)

A minimum of 500 square feet of usable open space per dwelling unit is required. The usable open space may be provided in any combination of common open space and private open space.

c.

Administrative Planned Residential Development Permit

(1)

A minimum of 300 square feet of usable open space per dwelling unit is required. The usable open space may be provided in any combination of common open space and private open space.

4.

Reserved.

5.

Parking. Parking shall be in accordance with Chapter 19.580 (Parking and Loading) with the following exceptions and additions:

a.

Planned Residential Development Permit projects.

(1)

A minimum of two fully enclosed (garage) spaces are required per dwelling unit.

(2)

A minimum of one guest space per three dwelling units is required. On-street parking may be credited toward this requirement. On-street parking is only allowed on a curb to curb street width of 28 feet or greater. Driveway spaces above shall not be counted toward these required guest spaces.

(3)

Recreational vehicle parking. Recreational vehicle parking is prohibited on a residential lot. A separate recreational vehicle parking lot is permitted, subject to requirements for adequate screening, including a required eight-foot high block wall, and five-foot landscape planters on all sides.

b.

Administrative PRD and Minor PRD projects.

(1)

A minimum of one guest space per three dwelling units is required. Interior on-street parking may be credited toward this requirement. On-street parking is only allowed on a curb to curb street width of 28 feet or greater. Driveway spaces may be counted toward these required guest spaces for Administrative PRD projects.

(2)

Recreational vehicle parking is prohibited.

6.

Building height.

a.

Per the underlying zone.

b.

For Administrative PRD and Minor PRD, the number of stories may be increased to three.

C.

Standards for RC Zone planned residential development.

1.

Lot size. In order to promote clustering, lots shall be a minimum of one-half acre in size and clustered in the less steep portions of the site.

Lot coverage maximum lot coverage requirements to be determined by the Planning Commission on a case specific basis based, in part, on product type, characteristics of the property and surrounding uses.

3.

Height. Same as RC Zone (See Section 19.100.040, Residential Development Standards).

4.

Setbacks. Same as RC Zone (See Section 19.100.040, Residential Development Standards).

5.

Common natural open space and clustering. Section 19.780.050 A (Benchmark Density) sets forth the criteria for a PRD to qualify for the benchmark density in the RC Zone, including provision of valuable natural open space and wildlife habitat and a site plan layout sensitive to the natural topography, both for wildlife habitat and resource conservation as well as visual aesthetic purposes. There is no minimum standard, although each development is encouraged to set aside a substantial portion of the site toward natural open space.

6.

Parking. A minimum of two fully enclosed (garage) spaces are required per dwelling unit.

D.

Standards for Small Lot Subdivision Planned Residential Developments - all R-3 Zones.

1.

Lot size and coverage. Minimum lot size and maximum lot coverage requirements to be determined by the Planning Commission on a case specific basis in part based on product type, characteristics of the property and surrounding uses.

a.

In no instance shall a lot resulting from a Small Lot PRD project be larger than 5,499 square feet.

2.

Height and Stories. Small Lot PRD projects shall have a maximum height of 35 feet and three stories.

3.

Setbacks. Setbacks shall be determined by lot size in accordance with the following but may be modified in conjunction with a PRD permit:

4.

Privacy Considerations. Small Lot PRD projects that abut the RA-5, RC, RR, RE, or R-1 Zone shall adhere to the following:

a.

Windows within 30 feet of a structure on another parcel shall not directly align with the windows of the neighboring structure.

b.

Upper story unenclosed landings, decks, and balconies that face or overlook an adjoining RA-5, RC, RR, RE, or R-1 Zoned property shall be located a minimum of 15 feet from the interior lot lines.

5.

Usable open space and recreational facilities.

a.

Usable open space shall be provided pursuant to Table 19.100.070 (Usable Open Space Standards: Multi-Family Residential Zones).

b.

The usable open space may be provided in any combination of common open space and private open space.

Parking.

a.

Parking shall be in accordance with Chapter 19.580 (Parking and Loading).

b.

Recreational vehicle parking is prohibited.

E.

Private streets. Refer to private street standards in Title 18.210.

(Ord. No. 7701, § 48, 2025; Ord. 7683, § 23(Exh. I), 2024; Ord. 7505 § 1(Exh. A), 2020; Ord. 7331 §113, 2016; Ord. 7027 §6, 2009; Ord. 6966 §1, 2007) 19.780.070 - Common ownership—Land or improvements.

A.

Planned Residential Development projects.

1.

Covenants, conditions and restrictions (CC&R's). Where a Planned Residential Development contains any land or improvement proposed to be held in common ownership, the applicant shall submit a declaration of covenants, conditions and restrictions (CC&R's) with the final map establishing a Home Owner's Association subject to City's Planning Division and the City Attorney's Office approval. Such declaration shall set forth provisions for maintenance of all common areas, payment of taxes and all other privileges and responsibilities of the common ownership. The CC&R's shall include provisions prohibiting the homeowners' association (HOA) from quitclaiming, selling or otherwise transferring the land held in common ownership to private property owners.

2.

Amendments to CC&R's. The provisions of approved CC&R's shall not be amended without the prior approval of the Community Development Director or his/her designee and City Attorney who at his or her discretion may refer the matter to the Planning Commission. Requests for amendments to existing CC&R's shall be submitted to the Planning Division.

3.

Maintenance. All private streets, walkways, parking areas, landscaped areas, storage areas, screening, sewers, drainage facilities, utilities, open space, recreation facilities and other improvements not dedicated to public use shall be maintained by the property owners. Provisions acceptable to the affected City Departments shall be made for the preservation and maintenance of all such improvements prior to the issuance of building permits.

4.

Failure to maintain constitutes a public nuisance. All commonly-owned lots, improvements and facilities shall be preserved and maintained in a safe condition and in a state of good repair. Any failure to so maintain is unlawful and a public nuisance endangering the health, safety and general welfare of the public and a detriment to the surrounding community.

B.

Administrative PRD, Minor PRD, and Small Lot PRD projects.

1.

Maintenance agreement required. An agreement for access and maintenance for all facilities used in common shall be submitted as part of the Subdivision Map. The agreement shall be approved by the City Attorney and recorded with the Riverside County Assessor-County Clerk-Recorder prior to the sale of any unit.

2.

The maintenance agreement shall be composed of and executed by all property owners to maintain all private streets, walkways, parking areas, landscaped areas, storage areas, screening, sewers, drainage facilities, utilities, open space, recreation facilities and other improvements not dedicated to public use.

3.

The maintenance agreement shall run with the land. Each owner and future property owners shall automatically become members of the agreement and shall be subject to a proportionate share of the maintenance and related costs.

4.

A final copy of the maintenance agreement, once recorded, shall be submitted to the Planning Division and Public Works Department for placement in the PRD and subdivision files.

(Ord. 7683, § 24, 2024; Ord. 7331 §113, 2016; Ord. 7235 §20, 2013; Ord. 6966 §1, 2007)

Chapter 19.785 - TRAFFIC PATTERN MODIFICATION MEASURES

19.785.010 - Purpose.

The City declares its purpose to encourage through traffic to use freeways and arterial streets rather than local residential streets. In order to achieve this purpose, The City may implement traffic pattern modification measures to discourage the use of local residential streets where reasonably warranted.

(Ord. 7331 §114, 2016; Ord. 6966 §1, 2007)

The following traffic pattern modification measures may be implemented subject to the procedures and findings contained in this chapter:

A.

Converting two-way streets into one-way streets; B. Street closures; C.

Addition of raised medians for traffic diverters and/or traffic circles to existing streets; and

D.

Any other modification measure consistent with the intent and purpose of this chapter.

(Ord. 7331 §114, 2016; Ord. 6966 §1, 2007)

19.785.030 - Procedures.

Traffic pattern modification measures applications shall be processed in accordance with the discretionary permit processing provisions as set forth in Chapters 19.650 (Approving Authority), 19.660 (General Application Processing Procedures), 19.670 (Notices and Hearings) and 19.680 (Appeals), 19.690 (Effective Dates) and other applicable Chapters of the Zoning Code.

(Ord. 7331 §114, 2016; Ord. 6966 §1, 2007)

19.785.040 - Required findings.

The Planning Commission may approve a traffic pattern modification measure, including conditions of approval if, from the evidence presented at the public hearing, the following written findings can be made: A.

The measure will provide for the health and safety of the citizenry and will not substantially impair the rendering of emergency and public services; B.

The measures will not unreasonably interfere with general traffic circulation via the public rights-of-way designated as major and secondary streets in the circulation element of the General Plan;

C.

There is sufficient evidence to indicate that one or more of these conditions exist:

An abnormally high percentage of traffic is unrelated to the local neighborhood and is merely passing through;

Street design or conditions permit excessive vehicular speeds;

3.

There is a separate street from the general neighborhood circulation pattern to preserve the unique character or adjacent properties, to encourage pedestrian, equestrian or non-motorized vehicular travel and/or to discourage crime, noise, air pollution, and other hazards to public safety and welfare; and 4.

In the case of street closure, a separate factual finding must be made that the street is no longer needed as contemplated by the California Vehicle Code Section 21101.

D.

The measures will not unreasonably restrict access to adjacent properties nor impair the constitutionally guaranteed rights of any individual or group. Releases may be acquired as determined by the City Attorney.

E.

The measures will not create an unacceptable internal circulation system characterized by any excessively long dead-end or cul-de-sac street, poor aesthetics, poor drainage, difficult maintenance requirements or poor street design geometry.

(Ord. 7331 §114, 2016; Ord. 6966 §1, 2007)

A.

In approving a traffic pattern modification measure case, certain safeguards may be required and certain conditions established to protect the public health, safety, convenience and general welfare and to assure that the purposes of the Zoning Code shall be maintained with respect to the proposal, traffic characteristics and environmental impacts of the proposal within the general area the proposal is to be located.

B.

The conditions attached to the traffic pattern modification measure case may include such provisions concerning improvements, design, operation characteristic, land use compatibility, general character, appearance, environmental impact, time limits for commencing the construction authorized, revocation dates, and other conditions the Planning Commission may deem appropriate and necessary to carry out the purposes of the Zoning Code and Chapter.

(Ord. 7331 §114, 2016; Ord. 6966 §1, 2007)