Chapter 19.48 — FENCES
Cupertino Zoning Code · 2026-06 edition · ingested 2026-07-06 · Cupertino
- For statutory provisions making fences taller than ten feet a nuisance, see Civil Code § 841.4. Prior ordinance history: Ords. 112, 686, 852, 1179, 1630, 1637 and 1777.
19.48.010 Purpose. ¶
The purpose of this chapter is to regulate the location and height of fences in yards of all zoning districts in order to protect the safety, privacy, and property values of residents and owners of properties within any zoning district of the City, including but not limited to residential, commercial, offices, institutional, industrial and/or agricultural properties. (Ord. 2085, § 2 (part), 2011; Ord. 1979, (part), 2006; Ord. 1788, § 1 (part), 1998)
19.48.020 Fence Location and Height in All Zones Except R1, RHS, R2, and R3 (up to Four Units).
Design Review shall be required for projects in all zoning districts except R1, RHS, R2, and R3 (with up to four units).
The Approval Body for a proposed project shall have the authority to require, approve, or disapprove fencing plans including location, height, and materials. Where an Approval Body is not identified, the Director of Community
Development, or his or her designee, shall have the authority to require, approve, or disapprove fencing plans and design.
The basic Design Review guidelines for the review of fences and walls are as follows:
Fences separating commercial, industrial, offices, and institutional zones from residential zones shall be constructed at a height and with materials designed to:
Acoustically isolate part of or all noise emitted by future uses within the commercial, industrial, offices, or institutional zones. The degree of acoustical isolation shall comply with the standards of Chapter 10.48.
Ensure visual privacy for adjoining residential dwelling units.
Fences shall be designed in a manner to provide for sight visibility at private and public street intersections (i.e. corner triangles or any sidewalk sight triangle).
Fence design shall be consistent with the standards outlined in this Title for the applicable zone.
Fences shall meet the regulations of any applicable Special Area Plan, Design Guidelines, or conceptual development plan.
At no point shall fence height exceed 10 feet without a Fence Exception*
*For statutory provisions regarding fences taller than ten feet in height, see Civil Code § 841.4.
(Ord. 2085, § 2 (part), 2011; Ord. 1979, (part), 2006; Ord. 1844, § 1 (part), 2000; Ord. 1788, § 1 (part), 1998; Ord. 24-2260, Att. A, (§ 1) 2024.)
19.48.030 Fence Location and Height for Properties Not Requiring Design Review. ¶
Table 19.48.030 sets forth the rules and regulations pertaining to fences on properties where design review is not required. Appendix A is a visual representation of the provisions of Section 19.48.030(A)–(C). The Director of Community Development is authorized to administratively make changes to Appendix A to clarify the intent of these provisions.
Table 19.48.030: Fence Location and Regulations
| 7 foot high fence | 3 foot high fence | ||||
|---|---|---|---|---|---|
| A. Front Yard | Not within required setback area, corner triangle, or sidewalk sight triangle. |
Along any property line, in any required setback area, corner triangle, or sidewalk sight triangle. |
|||
| B. Rear Yard | Along property line or in required setback area, except not allowed in any corner triangle or sidewalk sight triangle. |
||||
| C. Side Yard | 1. Interior residental lots: Along property line or in required setback area 2. Corner residental lots: Interior side: Along property line or in required setback area |
||||
| 7 | foot high fence | 3 foot high fence | |||
| --- | --- | --- | |||
| Street side: | |||||
| If the rear property | |||||
| line adjoins a rear | |||||
| property line , the | |||||
| setback from the | |||||
| side property line | |||||
| shall be 5 feet. | |||||
| If the rear property | |||||
| line adjoins a side | |||||
| property line of a key lot, in additon |
|||||
| to i. above, setback | |||||
| from street side | |||||
| property line, within | |||||
| 10 feet of adjacent | |||||
| property line shall be | |||||
| 12 feet. | |||||
| Street side: | |||||
| --- | --- | --- | |||
| If the rear property | |||||
| line adjoins a rear | |||||
| property line , the | |||||
| setback from the | |||||
| side property line | |||||
| shall be 5 feet. | |||||
| If the rear property | |||||
| line adjoins a side | |||||
| property line of a key lot, in additon |
|||||
| to i. above, setback | |||||
| from street side | |||||
| property line, within | |||||
| 10 feet of adjacent | |||||
| property line shall be | |||||
| 12 feet. | |||||
| 1. Open Fencing (composed of materials which result in | |||||
| D. Additonal Regulatons for Residental Hillside, Open Space Zoning |
a minimum of 75% visual transparency), shall be unrestricted. 2. All Other Fencing which otherwise meets the regulatons in Secton 19.48.030(A)-(C): |
||||
| Districts, and R1 Propertes with an |
Net lot area < 10,000 square feet: Not limited. | ||||
| Average Slope Over | Net lot area > 10,000 square feet: 5,000 square | ||||
| 20% | feet (excluding the principal building) of net lot | ||||
| area may be enclosed with solid board fencing. | |||||
| E. In areas where a seven (7) foot fence is allowed, an up to eight (8) foot high fence can be constructed, subject to building permit approval and upon receipt of writen approval from abutng property owners. |
F. Hedges exceeding the height requirements for fences outlined in Section 19.48.030(A)-(C) are allowed:
Within interior side and rear yards; and
Within front or street side yards, if perpendicular to the front and street side property lines and outside of required corner triangle or sidewalk sight triangles
| 1. Shall only be included in design of fences within a yard abutng a street lot line; and |
||
|---|---|---|
| 2. Shall be limited to one entry feature per street | ||
| frontage; and | ||
| 3. Must be incorporated into the fence design, | ||
| structurally a component of the fence, and shall not be considered an additonal allowance for an |
||
| G. Minor ornamental | accessory structure within required setbacks; and | |
| entry features (e.g. arbor, trellis, entry gates, light fxtures meetng the requirements of Chapter 19.102). |
4. Shall be no taller than eight (8) feet and shall not exceed a cumulatve area of twenty-fve (25) square feet; and 5. Shall not be located in any required fag lot access area, access easement, corner triangle, or sidewalk sight triangle; and |
|
| 6. When viewed from the street, the feature shall be no | ||
| wider than: | ||
| Six (6) feet on lots with less than 60 feet of street | ||
| frontage, or | ||
| Eight (8) feet on lots with 60 feet or more of | ||
| street frontage. |
H. Notwithstanding any other provision of this chapter, fences shall not be located in any future right of way dedication area, and setbacks shall be measured from any planned future street line, as determined by the Public Works Department.
I. If the Director of Community Development determines that a proposed fence is widely visible to public view and has the potential to create impacts on the visual character of an area (for example, blocks public views from the valley floor to the hills or an open space reserve), then the proposed fence shall comply with the requirements in Sections 19.48.030D(1)(b) & 19.48.030D(2) regardless of lot size.
==> picture [325 x 252] intentionally omitted <==
(Ord. 2085, § 2 (part), 2011; Ord. 24-2260, Att. A, (§ 1) 2024)
19.48.040 - Fence Design Requirements. ¶
Prohibited Materials:
The following materials shall be considered “Prohibited Materials” for purposes of this Chapter:
Unless required by law or regulation of the City, State or Federal Government, barbed wire, razor wire, chicken wire and similar small-gauge wire or mesh product, and/or electrified fencing are prohibited.
Fences made of non-engineered plastic, fabric membranes, cloth, canvas, plywood, uncoated cyclone/chain link, and reed or bamboo with sticks and slats smaller than four inches in width are prohibited, unless located in areas not visible from public areas or adjacent properties.
Allowed Materials: Allowed materials include, but are not limited to wood, engineered plastic, vinyl coated cyclone/chain link, metal (e.g. wrought iron), brick, block, stone, and other comparable (safe and commercially acceptable) materials intended for fence use.
Material colors shall be natural earth tone and/or vegetation colors including natural hues of brown, green and shades of gray and shall have a reflectivity value of 60 or less.
Other materials, except Prohibited Materials, may be allowed if deemed appropriate through Design Review approval.
The area between the back of curb and any fencing shall be landscaped, with a suitable permanent irrigation system where necessary, or have pervious flatwork, and be continuously maintained by the property owner.
General Maintenance: All fences adjacent to a street, sidewalk, or public right-ofway shall be continuously maintained free of visible and structural defects.
(Ord. 24-2260, Att. A, (§ 1) 2024)
19.48.050 - Proximity of Plants and Fences to Public Streets. ¶
The proximity of plants and fences to public streets shall be controlled by the provisions of Chapter 14.08 of the Municipal Code.
(Ord. 24-2260, Att. A, (§ 1) 2024)
19.48.060 Roadway and Driveway Gates. ¶
Roadway and Driveway gates are allowed if they comply with the Fire Department Standard Details and Specifications for Security Gates for access roadways and driveways and the criteria in Sections 19.48.969(A)-(C). Roadway and driveway gates in existence prior to September 20, 1999, with necessary permits to install them, are permitted to be replaced. All unpermitted roadway and driveway gates must comply with the regulations outlined below, when replaced.
Table 19.48.060: Roadway and Driveway Gate Regulations
| A. All Residental Districts, Except RHS: |
1. A driveway gate meetng all of the following requirements may be installed, subject to building permit approval: The driveway gate shall be set back as follows: Interior and Corner Lots: A minimum distance of 20 feet or in accordance with Fire Code standards, whichever is larger, and measured from the front and/or street side property lines, from the future street line, or from the property line afer right-of- way dedicaton area as determined by the Public Works Department. However, in no case shall the driveway gate be located in front of the building wall line of a primary structure nearest to the right of way; Flag Lots: A minimum distance of 20 feet or in accordance with Fire Code standards, whichever is larger and measured from the property line closest to the street, from the future street line, or from the property line afer right-of-way dedicaton area as determined by the Public Works Department. The driveway gate shall meet all height regulatons described in Secton 19.48.030; and The driveway gate shall not be located in any required corner triangle or sidewalk sight triangles; and The driveway gate shall not impede required paths of travel for compliance with the State and Federal law; and No more than one driveway gate shall be allowed per property; and The driveway gate opening shall not be wider than 20 feet; and The driveway gate shall not be located in a driveway for a side entering garage; and The driveway gate shall not be located in a manner which interferes with the required open of-street parking on a site; and The driveway gate shall meet the fence design requirements outlined in Secton 19.48.040 and shall not make use of collapsible materials (e.g. scissor gates); and Driveway gates shall meet the regulatons of any applicable Special Area Plan, Design Guidelines, or conceptual development plan; and The Fire Department shall approve the locking mechanism and locaton of the gate. 2. A Fence Excepton shall be obtained for any driveway gates that do not meet the standards outlined above. These driveway gates shall meet all the following: The driveway gate shall be setback a minimum distance of 20 feet from the front and/or street side property lines, from the future street line, or from the property line afer right-of-way dedicaton area as determined by the Public Works Department, whichever is greater, and not be located on or along any property line; and The Applicant must provide documented evidence that the gates are needed for demonstrated security and/or demonstrated safety reasons, which would not |
|---|---|
| otherwise be mitgated by placing a fence or driveway gate in a manner permited by the Municipal Code; and The Fire Department approves the locking mechanism and locaton of the gate. |
|
| --- | --- |
| B. RHS Zoning District: |
1. Roadway and Driveway Gates may be used to control access to private roads and driveways provided that the design of the gate, including locaton, dimension and the locking mechanism, are approved by the Director of Community Development afer consultaton with the Fire Department. |
| C. Other Development: |
1. A driveway gate meetng all of the following requirements may be installed, subject to Administratve Design Review approval. All driveway gates shall: Be setback a minimum distance of 20 feet from front and/or street side property lines. However, under no circumstances shall the gate be located closer to the property line than the locaton of the building wall of the primary building located on the property; and Not be located in any corner triangle or driveway sight triangle; and Not be installed in any parking area or porton of parking facilites designated for commercial, retail parking, and/or customer serving ofce, 2. An at-grade driveway gate shall: Be no taller than seven feet in height; Utlize architecturally decoratve and at least 50% open materials; and Secure an open, surface parking lot which is largely obscured from views from the right-of-way by existng structures and serves a private use (e.g. church, ofce, multple-family development); 3. Driveway gates for parking structures and below grade parking shall be allowed: When proposed to assure availability of parking for diferent uses (e.g. separatng ofce and residental parking) in a shared parking structure; When proposed to secure access for a single, private use; 4. The driveway gate is required as a conditon of approval of obtaining federal or state funding for development; 5. The driveway gate shall meet the fence design requirements outlined in Secton 19.48.040 and shall not make use of collapsible materials (e.g. scissor gates); and 6. The Fire Department shall approve the locking mechanism and locaton of the gate. 7. A Fence Excepton shall be obtained for any driveway gates that do not meet the standards outlined above, prior to issuance of building permits. Roadway and driveway gates that do not meet the standards outlined above may be approved through a Fence Excepton only if the development can adequately justfy that the proposed gates are needed for demonstrated security and/or demonstrated safety reasons. |
(Ord. 2085, § 2 (part), 2011; Ord. 24-2260, Att. A, (§ 1) 2024)
19.48.070 Exceptions–Findings. ¶
Where practical difficulties, unnecessary hardships, or results inconsistent with the purpose and intent of this chapter result from the strict application of the provisions hereof, exceptions may be granted as provided in Chapter 19.12, and this section for all zoning districts except the RHS Zoning District, in which case a Hillside Exception must be obtained in accord with the requirements of Section 19.40.040 and Section 19.40.070. The Approval Body may grant a request for a Fence Exception only if all the following findings can be made:
The literal enforcement of the provisions of this chapter will result in restrictions inconsistent with the spirit and intent of this chapter and the proposed development is otherwise consistent with the City's General Plan and with the purpose of this chapter as described in Section 19.48.010.
The granting of the exception will not result in a condition which is materially detrimental to the public health, safety or welfare or result in a hazardous condition for pedestrian and vehicular traffic.
The exception to be granted is one that will require the least modification of the prescribed regulation and the minimum variance that will accomplish the purpose.
When driveway, roadway, and structured parking gates not meeting allowed standards are proposed: The proposed development meets the requirements of the Santa Clara Fire Department and Sheriff's Department, and if security gates are proposed, that attempts are made to standardize access.
When fences and gates that exceed allowable height limitations are proposed: The fence height for the proposed residential fence is needed to ensure adequate screening and/or privacy.
(Ord. 2085, § 2 (part), 2011; Ord. 24-2260, Att. A, (§ 1) 2024)
19.48.080 Temporary Fences for Construction. ¶
The Building Official may require persons constructing structures in the city to erect and maintain temporary fences around all or a portion of the construction site in order to secure the site from entry by the general public. Any such fencing may only be erected during the time a valid building permit is issued for construction.
Temporary fences are not required to comply with the location requirements of Section 19.48.030 but shall not be located in any corner or sidewalk sight triangle.
Temporary fence materials are restricted to non-combustible materials and must screen construction activities. Temporary fence materials shall be consistent with the prohibited and allowed materials outlined in Section 19.48.040 (A) and (B), except that uncoated cyclone/chain link fences may be allowed.
All fences adjacent to a street, sidewalk, or public right-of-way shall be continuously maintained free of visible and structural defects.
(Ord. 2085, § 2 (part), 2011; Ord. 1979, (part), 2006; Ord. 1777, (part), 1998; Ord. 24-2260, Att. A, (§ 1) 2024)
19.48.090 Violation–Penalty. ¶
Any person who violates the provisions of this chapter shall be guilty of an infraction and upon conviction thereof shall be punished as provided in Chapter 1.12.
(Ord. 2085, § 2 (part), 2011; Ord. 1979, (part), 2006; Ord. 1788, § 1 (part), 1998; Ord. 242260, Att. A, (§ 1) 2024)